Marvel MO15CRS1XS Manual
Læs gratis den danske manual til Marvel MO15CRS1XS (24 sider) i kategorien Ismaskine. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Marvel MO15CRS1XS, eller vil du spørge andre brugere om produktet?
Side 1/24
Installation
Operation and
Maintenance
Instructions
Ice Machine
MO15CRS1XS (Outdoor)
Installation Operation and Maintenance Instructions
Contents
Intro
Operating Instructions
Ice
Airflow and Product Loading
Maintenance
Cleaning
Cleaning Condenser
Service
Troubleshooting
Warranty
Obtaining Service
Environmental Requirements
Electrical
Cutout Dimensions
Product Dimensions
Side by Side Installation
Water Hookup
Anti-Tip Bracket
General Installation
Grille Installation
Door Swing
Door Adjust
Safety
Safety and Warning
Disposal and Recycling
Installation
First Use
Extended Non-Use
2
Welcome to the Marvel Experience
Congratulations on adding a crescent ice maker home and thank for new Marvel to your you
choosing our quality American-built product. years of crescent ice the comfort and You’ll enjoy in
convenience of your home, backed by our full worry-free thrilled to welcome warranty. We are you
to our growing community of Marvel trust in our products and our support. owners, who
The information in guide is intended to help you your new crescent this install and maintain Marvel
ice maker to protect and prolong the your unit. We contact our lifetime of encourage you to
Technical at (800) with any questions. Support team 223-3900
Cheers!
Installation Operation and Maintenance Instructions
3
Electrical
!WARNING
SHOCK Electrical Grounding HAZARD — Required.
Never attempt to repair or perform maintenance on the
unit until the electricity has been isconnected. d
Never remove the round grounding prong from the plug
and never use a two-prong grounding adapter.
Altering cutting or moving power , , re cord removing
power ug, or pl direct wiring can cause serious injury,
fire, loss of and/or life, property and wi void the ll
warranty.
Never use an extension cord to connect power to the unit.
Always keep your rking area dry. wo
NOTICE
E must all lectrical installation observe state and local
codes. This requires connection to unit a grounded
(three-prong), polarized receptacle that has been placed
by a qualified electrician.
Th un requ grounde it ires a ed and polari VAC, 60 zed 115
Hz, power su (norm hous current) An 15A pply al ehold .
individual, proper grou branch circui circuit ly nded t or breaker
is recommend GF (groun circuit ed. A CI d fault interrupter) is
usua requir fixed location lly not ed for appliances and is not
recommend for your un because ed it it could pron to be e
nuisance tripping Ho be sure . wever, to cons your local ult
codes.
S DIMENS recommended receptacle ee CUTOUT IONS for
location.
Cutout Dimensions
PREPARE SITE
Your product Marvel has been designed for ei free- ther
s or built-in installatitanding on. When built-in your unit , does
not require additional air space for top, sides, or rear.
However, the fron grille must NO be obstructed, t T and
clearance is required for electrical an connecti in on the rear.
!CAUTION
Unit inst can NOT be alled behind closed cab a inet door.
CUTOUT DIMENSIONS
34-1/4"
(870 mm)
to 35"
(889 mm)
15-1/4"
(387 mm)
24"
(610 mm)
4"
(102 mm)
7"
(178 mm)
5/8"
(16 mm)
Preferred location
for water line and
ele trical outlet is in c
adjacent cabinet.
Installation Operation and Maintenance Instructions
5
Product Dimensions
*Add 3/4" To Depth For Water Line Clearance
Installation Operation and Maintenance Instructions
Not Including Handle
6
Side-by-Side Installation
Two may units be installed side-by-side.
Cutout widt side-by-side installati is the h for a on
cutout dimension sing un times two. of a le it
No tr kit is required. However, 1/4" (6 mm) of space im
need maintain bes to be ed tween the units to ensure
unobstructed door swing.
Units must operate from se parate, properly grounded
electrical receptacles placed according to each unit’s
electrical specifications requirements.
Side-by-Side Installation with Bracket
1. Slid units so screws to units easilye both out on p of are
accessible.
2. Remove hown screws as s below.
3. Pl bracket holes a attach unit with twoace over nd to
screws removed step 2 using a T-25 in Torx driver.
Tighten fully.screws
4. Gently its on. Be careful push un into positi not to entangle
the or electrical co rd w line, if applicable.ater
5. Re-ch leveling,eck the from front to back and side to side
Make any necessary adjustments. unit’s top The surface
should be mm) approximately 1/8" (3 below the
countertop.
Installation Operation and Maintenance Instructions
7
Water Hookup
PREPARE PLUMBING
The water uses 1/4" mm) valve a standard (6.35
compressio fitting. n
!CAUTION
Plumbing installation must observe all state and local
codes. All water and drain connections MUST BE made
by a licensed/qualified plumbing contractor. Failure to
follow recommendations and instructions may result in
damage and/or harm.
Water Supply Connection
When connecting the water supply, plea note the se following:
•Before installing the unit and connecti cold ng to the water
su the pply, review local plumbing codes.
•The wate pressu sh be be 20 an psir re ould tween d 120
(138 an 82 kPa). d 7
•T water li MUST have a shut-off valve in the he ne supply
line.
•T s loophe water line hould be ed in coils. Thi will to 2 s allow
the unit to remov be ed for cleaning an servicing. d Make
certain th pinche damaged at the tubing is not d or during
installation.
!CAUTION
Do any supply line. not us e plastic water The line is under
pressure all at times. Plastic may crack or ruptur with e
age and to cause damage your home.
Do no use tap or joint compound when t e att a aching
braided flexib includes rubber le water supply line that a
gasket gasket. The provides – an seal adequate other
materials could of cause blockage the valve.
Failure to follow recommendations and instructions may
result in damage and/or harm, flooding void or the
prod warranty.uct
!CAUTION
Turn off water supply and disconnect electrical supply
to unit prior to installation.
Use when panel. caution handling back The edges
could be sharp.
1. Turn of waterf supply and discon electr supply nect ical to
product prior to at installation. tempting
2. Remove th ba panel.e ck
Installation Operation and Maintenance Instructions
8
3. Loca watete r valv inlet.e
4. Break away filler feature
in bushin wig th flat
screwdriver.
5. Thread wa line ter through
back panel hole (with
bushing).
6. Loc a watete r valv inlete
and connec tot valve.
7. Tu supply rn on water and
chec leaks.k for
8. Reinstal back panel.l
9. Instal reta clip.l ining
Remove
ZLWKɠDW
screwdriver
1. Slid unite out so screws on top unit of are easily
accessible.
2. Remove th se two crews opposi from the te side of the
hinge assembly ng a usi T-25 T below).orx driver (see
3. Place bracket over and holes attach to unit with two
screws in 2 a removed step using T-25 Torx driver.
Tighten screws fully.
4. Gent push unit into position. not to ly Be careful entangle
the or electrical co rd w line, if applicable.ater
5. Check be the to sure unit is level fro to back from nt and
side to Make side. any necessary adjustments. Th unit’se
top surface should be approximately
1/8" (3 mm) countertop.below the
6. Secure ng bracket adjoini into surface.
Installation Operation and Maintenance Instructions
Anti-Tip Bracket
9
Grille Installation
REMO INSTALLING GRILLEVING AND
WARNING
!
Disconnect electric power to he unit t before removing
the grille.
When using the unit, the grille mu best installed.
Removing the grille
1. Disconnect power to the unit.
2. Loosen the two screws (1).
3. Remove grille (2).
Installing the grille
1. Align cabinet and but do grille holes and secure, not
over le screws tighten gril (1).
2. Reconnect to unit. power the
Door Swing
Unit ha clearancs ve a zero e for to the door open 90°, when
instal adja to cabinets. led cent
Stainless ack Steel and bl and white odels m require
2-1/8" (5 clea to4 mm) door rance accommodat ife the handle
instal next wall.led to a
Integrat modelsed require 1/4" mm) clearanc if (6 e installed
next wall Al additional sp any to a . low for ace for knobs or
pull installe th integrat panel/frame.s d on e ed
Wall Wall
90
Door Swing
90
Door Swing
2-1/8" Min.
(54 mm)
1/4" Min.
(6 mm)
Installation Operation and Maintenance Instructions
11
Door Adjust
HINGE COVER
Hinge cover included with stainless models is black and
optional.
To inst hinge cover: all
Press hinge square hinge cover ly over
DOOR ALIGNMENT AND ADJUSTMENT
Alig an adjust t if it is not level is non d he door or t sealing
properly If is. the door not sealed, y the unit ma not cool
properly excessiv, or e frost ma form in th interior.y e
NOTICE
Properly aligned, the should door s gasket’ be firmly n i
cont with the cabinet all the way act around the door
(no gaps). Carefully examine the door s gasket to ’
ensure that it is fi in rmly contact with the Also cabinet.
make the sure door et t n e e gask is no pinched o th hing
side of the door.
T alig door:o n and adjust the
1. Gently e er pry off hing cov from top of unit.
2. Loosen bottom hinge (do not remove) top and screws
using the top a a orx T-25 screwdrive T r on and 1/4”
socket on the bottom.
3. Align wi cabinet. door squarely th
4. Make sure gasket is rmly in contact with cabinet thefi all
way around the door (no gaps).
Tighten bottom hinge screws.
Tighten hinge and replace nge top screws hi cove . r
L of unit ma make desirable moun the ocation the y it to t door
on the side the opposite of cabinet.
Th hi hardware wi be removed an reinstalled the e nge ll d on
opposite of side the cabinet.
TO REVE THE DOORRSE (Black and Stainless Models)
6.
5.
Remove top hinge and door:
1. Remove hi sc c from unit.nge and rew overs top of
2.
Ho to it from falling.ld door keep
3.
Remove hi cabi a orx T-25 top nge from net using T
screwdrive remove thr screws.r to ee
4.
Remove vot screw m hinge, flip nge pi fro hi over, and
insta i from ll the pivot screw n the same hole the
opposi surface.te
Top Hinge
Right Side
Top Hinge
Left Side
Pivot
Screw
Installation Operation and Maintenance Instructions
Hinge Cover
12
Remove by forwar liftin off door tilting d and g door
bottom hinge. Retain shoul washers; they will der be
reused.
Remove three screws hinge holes from on the opposi te
side. Reinstall into holes the where hinge was removed.
Take not care to scratch cabinet.
Remove hinge: bottom
1. Remove cabi usi 1/4” socket. bottom hinge from net ng
2. Remove corresponding screws on opposite ofside
cabinet. On models be a some there may nut behind one
or both screws on either side.
In bottom hinge:stall
Insta thr screwsll two or ee , depending on mo Replace del.
nuts if used.
In hing and door:stall top e
1. Install the top hinge. Do not tighten.
2. Rotate door 180° to reverse and set onto the the door
bott hinge.om
3. Align edge of the hinge with the outer edge of the unit.
4. Tighten th screws replac ree and e hinge cover.
5.
6.
Align and adjust the door:
Align and adjust the door (see DOOR ADJUST).
Installation Operation and Maintenance Instructions
13
NOTICE
Do not place cans or bot tles in the ice
compartment because they will freeze.
To turn off ice production: Rais bi into e the n arm an
uprigh an lock positit d ed on. unit The will preserve
temperature for ic storage. e
NOTICE
If not intending to use the ice maker, turn the water
supply valve off. It is also im to portant raise e bin arm th
of the ice maker ee above). (s Failure to raise the bin arm
may result in damage to the water valve.
Certai soun are norm during unit’ operatio You n ds al the s n.
may compress fa wa valve, hear the or or n the motor, ter or
ice the ice dropping into bucket.
!CAUTION
NEVER use an ice pick, knif or other sharp e instrument
to separate cubes. Shake the ice bucket d. instea
During periods limite of d us high ambient e or temperatures, it
is common for cubes fuse together. to Gently sha th ke e
buck brea apar cubes. If no using et to k t t the e maker ic
regu emptlarly, y the ice bucket periodically to ensure fresh
cubes.
It for appear is normal cubes to cloudy. The cause is air
trap in wa beca of fast freezin It is not ped the ter use g. caused
by heal tast or the th, e chemical the wa It is make up of ter. the
sa ai is every glass of w you me r that in ater drink.
Remove ice bucket the for em cleaning To ptying and .
remove the bucket, ice raise the bi ar remove the n m and
bucket from ice ent. Use bucket the compartm the ice for ice
storage only.
OFF
ON
First Use
A presetll controls are at factory. Init startup the ial
requir adjustments. es no
NOTICE
Marvel recommends discarding th produced e ice
during of the to hours first two three operation to avoid
possible dirt or sc t dislodge ale hat may from the water
line.
To turn t off: he or unit on
Press the rocker sw locaitch ted door the front inside the on
panel, the or behind grille.
Ice
ICE MAKER OPERATION
When the ice bu fullcket is , the ice making mechanis will m
sh refrigeration system wi continue ut off. However, the ll to
c maintain supply.ool and the ice
OFF
ON
Installation Operation and Maintenance Instructions
14
ICE MAKER ADJUSTMENT
Ice Cube ess Adjustment Thickn
Interval - As Required
On ice maker the be equipp m adjued odels, st cu size by
changi wateng r ed to he amount inject in t ic maker e
assembly as follows:
1. Remove e th ice maker sembly r as cove (1).
2. Fi adjust scnd the ing rew on e ker th ic mae assembly
control he g box (2). T adjustin screw low is just be the
minu (- an sign box.s ) d plus (+) s on the control
!CAUTION
Too large of an the screw can adjustment to cause
the overflow maker water to the ice and can cause
property damage.
3. Turn g the th adjustine sc towarew rd minus (-) sign
(clockwise) for maller bes or toward the plus s cu (+) sign
(counterclockwis larger cubes.e) for
4. Instal th ic as cover.l e e maker sembly
ADJUSTING ICE HARVEST
1. Remove th front grile le (see GRILLE INSTALLATION).
2. Using screwdriver, turn the ng a flat ti p adjusti screw
(3) a rement r small inc clockwis foe a COLD setting ER
(slower production) ice or for counterclockwise a
WARMER setting (faste r ice production).
3. Reinstal th front gri (t screws).l e lle wo
1
2
C
O
L
D
E
R
Warmer Colder
3
12
Airflow and Product Loading
NOTICE
The unit requires proper airflow to perform at its highest
efficiency. Do no t block the front grille at any time, or the
unit will not perform as expected. Do not install the unit
behind a door.
Installation Operation and Maintenance Instructions
15
Cleaning
EXTERIOR CLEANING
Stainless door panels, handles and frames can discolor when
exposed to chlori gas, ne pool chemicals, saltwater or
cleaners with bleach.
Keep new your stainles uni looking s t by cleani wi a ng th good
quality all- stainles s and polish in-one s teel cleaner monthly.
For best results us Clairee ® St Steel ainless Polish and
Cleane . Comparable products ar acceptable. r e Frequent
cleaning will remove s contamination that urface co to uld lead
rust. installations ma requir cleaning Some y e weekly.
Do not clean with steel pads. wool
Do not st or on use stainless eel cleaners polishes any
glass surfaces.
Clean any gl wi non-chlorine glass ass surfaces th a cleane .r
Do not cleaners specifical for use not ly intended
stainless steel urfaces on stainless s (this includes glass,
t cleaners).ile and counter
If an surfac discolorin rusti appears, clea it y e g or ng n quickly
with Bon-Ami® or ers iend Barkeep Fr Cleanser® and a
nonabrasiv clo Always cl wi grain. e th. ean th the Always finish
with Claire ® Stai St Poli and nless eel sh Cleaner or
comparable uct to prod prev further ent problems.
Using abrasive pads such as ScotchBrite™ will cause
the graining in the stainless to become blurred.
Rust not cleaned up promptly pene the can trate surface
of the stainless steel and mplete co removal of the rust
may not be possible.
INTERIOR CLEANING
Dis unit. connect power to the
Clean interior the and removed all components using a mild
nonabrasi detergve ent an solution d warm water applied with
a soft sponge or non-abrasive cloth.
Rinse the nterior ng a i usi soft cl water. sponge and ean
Do not use any solvent-based or abrasive cleaners.
These of eaners may transfer taste types cl to the interior
products and damage discolor or the interio . r
Installation Operation and Maintenance Instructions
16
DEFROSTING
Manual Models Defrost
This unit is a manual defrost l mode and will require
occasional defrosting. When there is buil d-up of
1/4" (6 mormm) or e of frost, manual th unit.ly defrost e
!CAUTION
DO NOT use an ice pick or sharp other instrument to
help speed up defrosting. These instruments can
puncture inner lining r the o dam the cooling unit. DO age
NO use an type of T y heat to defrost. Using a heater to er
speed up defrosting can cause person injuryal and
damage to the inner lining.
To defrost:
1. Disconnect unit.power to the
2. Remove ice bucket and discard ice.
3. Place towel or her on ot absorbent material bott of om ice
bin.
4. Fill ic buck ha with not water. the e et lf full warm, hot This
wi unit faste .ll the help defrost r
5. Pl buck inace the ice et back to th unit top of the e on towel
or her sorbent ot ab material.
6. P th door i an op positi (2 in [5 mm]rop e n en on . 0
minimum).
7. Afte 1 remover about hour the bin and ice discard water.
8. Allow th fros to melt naturally. e t
9. Afte fros melt completr the t s el clea th and y n e interior all
remov components. CLEANING).ed (See INTERIOR
NOTICE
DO NOT clean ice buck using a dishwasher The et . bucket
is not dishwasher safe will be and damaged.
10.When the interior is dry, reconnect power and turn unit
on.
NO o safeguar agains contaminates in ice,TE: T d t discard
fi thr batches ic af defrosting.rst ee of e ter
Installation Operation and Maintenance Instructions
17
Produkt Specifikationer
| Mærke: | Marvel |
| Kategori: | Ismaskine |
| Model: | MO15CRS1XS |
Har du brug for hjælp?
Hvis du har brug for hjælp til Marvel MO15CRS1XS stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ismaskine Marvel Manualer
14 Juni 2025
1 Oktober 2024
30 September 2024
30 September 2024
30 September 2024
30 September 2024
30 September 2024
30 September 2024
30 September 2024
1 September 2024
Ismaskine Manualer
- Follett
- Kogan
- Xsquo
- ECG
- Rommelsbacher
- Proficook
- Aroma
- Gourmia
- G3 Ferrari
- Igloo
- Maxxfrost
- Kalorik
- Lagrange
- Cattabriga
- OBH Nordica
Nyeste Ismaskine Manualer
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025
15 Juni 2025