Mastervolt C3-RS Manual

Mastervolt Batterioplader C3-RS

Læs gratis den danske manual til Mastervolt C3-RS (3 sider) i kategorien Batterioplader. Denne vejledning er vurderet som hjælpsom af 8 personer og har en gennemsnitlig bedømmelse på 3.8 stjerner ud af 4.5 anmeldelser. Har du et spørgsmål om Mastervolt C3-RS, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

ASTER ISION MODULAR SWITCHBOARDS

HOW TO ASSEMBLE A MASTERVISION PANEL

HOW TO LABEL A BACKLIGHT DC MODULE

AC MODULE

1. Lethal voltages exist on your vessel. Make sure all shore power, onboard

generating sources and batteries are disconnected before beginning

installation of your electrical panel.

2. AC modules will have lethal voltages on the bus bars and terminals.

Additional safety enclosures as the AC protection shield (part no. 07-09-04601-2-3)

may be required in some installations.

3. Make sure all Ac modules are bonded tot the ship’s AC ground bus. When

grouping modules together to form your panel, a single ground may be used.

Use an ohm meter to verify ground to all modules.

CAUTION GENERAL

1. Verify the modules you purchased arev configured for the source voltage

aboard your vessel / mobile. Refer to the backlight specification.

2. Installation of Mastervision panels should be completed by a person with

a thorough knowledge of marine / mobile electrical systems.

3. Wiring to and from each module should be conform to the local applicable

standards and taking into consideration the safety guidelines and measures.

Mastervolt can accept no liability for damage due to the use of the panel or

due to possible errors in the manual and the results thereof.

1. For best results, use Mastervision installation parts

2. Use connector bar 07-09-07810 and connector block

07-09-07820 to assemble the panel.

3. The mounting bolts used are M4x25

4. Secure the bolts wit hte supplied M4 nuts and O-rings.

5. To fasten the electrical panel in its frame or bulkhead use

the the stencil as supplied to cut the panelhole.

connector bar

07-09-07810

connector block

07-09-07820

HOW TO INSTALL THE BACKLIGHTING SYSTEM:

The Mastervision panels have a two-state backlight system for label illumination.

The first state is a low intensity green light that illuminates the labels on the

panel to enable label viewing in low light conditions, any time the circuit is

switched ON or OFF. The second state is a higher intensity yellow DC LED

(or orange neon lamp for AC) to indicate when a circuit is switched ON.

Power must be fed to all modules with backlight capability. This is achieved by

linking all the modules together by their backlight connectors (see drawing).

Verify the backlight AC or DC voltage on each module.

Do not use connector blocks at the outside top or

bottom edge. This is where the complete panel

will be fastened to its frame or bulkhead.

backlight

5DC

Indicator wire to

load side of breaker

busbar

for 5 breakers

To place the labels on the backlight module

remove the mounting bolts and turn the module

around.

Place the label in the embossed square on the

lens. Make sure that the label is placed

correctly and the indicator led is

uncovered.

Replace the backlight module in the

original position.

Warning:

When the module is placed correctly the

indicator led is 1mm away from the

transparant front lens.

NAVIGATION

INSTRUMENTS

1mm

10/30V power supply

L phase

N neutral

connect the indicator

wire to the load side of

the breaker

10/30V power supply

10/30V DC power supply for backlight

Note:

The power supply voltages are equal on all backlight modules,

indicator voltages are depending on the type of panel.

Produkt Specifikationer

Mærke:	Mastervolt
Kategori:	Batterioplader
Model:	C3-RS

Har du brug for hjælp?

Hvis du har brug for hjælp til Mastervolt C3-RS stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Batterioplader Mastervolt Manualer

Mastervolt Magic 24 12-20 Manual

23 August 2024

Mastervolt Mass Combi Pro 24 3500-100 Manual

23 August 2024

Mastervolt Mass 24 100-2 Manual

22 August 2024

Mastervolt Digital AC 1x6A Manual

22 August 2024

Mastervolt CombiMaster 12 2000-60A Manual

22 August 2024

Mastervolt Mac 24 12-20 Manual

22 August 2024

Mastervolt Mass 48 50 Manual

22 August 2024

Mastervolt DC Master 12 12-3A Manual

22 August 2024

Mastervolt Laadstroomverdeler Battery Mate 2503 IG Manual

21 August 2024

Mastervolt Mass Combi Ultra 48 3500-50 Manual

21 August 2024

Batterioplader Manualer

Nyeste Batterioplader Manualer

Nedis WCHA20WTUL Manual

3 November 2025

Guest ChargePro 2707A Manual

3 November 2025

Nedis WGCHA100WWT Manual

2 November 2025

Victron Energy Orion-Tr Smart Manual

2 November 2025

Nedis WCHAC20WT Manual

2 November 2025

Savio LA-06 Manual

25 Oktober 2025

Goji GQICAR17C Manual

19 Oktober 2025

Tecmate Optimate 5 Voltmatic Manual

19 Oktober 2025

Sungrow IDC30E Manual

18 Oktober 2025

Sungrow SG33CX Manual

18 Oktober 2025