Maxsa 43319-X Manual

Maxsa Ikke kategoriseret 43319-X

Læs gratis den danske manual til Maxsa 43319-X (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Maxsa 43319-X, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

ASSEMBLY AND INSTRUCTION GUIDE

ABOUT YOUR LED OUTDOOR WALL SCONCE

The

LED Outdoor Wall Sconce

is perfect for porches,

doorways, or around the house.

The

LED Outdoor Wall Sconce

has a built-in motion sensor,

which automatically turns on the light when movement of a

heat source (such as people, animals, or cars) is detected in

the area. The light remains on while motion continues to be

detected in the area.

The

LED Outdoor Wall Sconce

also has a built-in photosensor

so that the light only turns on at night.

The

LED Outdoor Wall Sconce

may function irregularly or not

at all at temperatures below ˚ F / ˚ C. 0 -17.8

Normal operation will return when the temperature rises.

The

LED Outdoor Wall Sconce

requires 4 C cell batteries (not

included). The batteries typically last up to 1 year under

normal use.

The 5 super bright LEDs in the

LED Outdoor Wall Sconce

have an estimated life of 30,000 hours so they should never

need changing.

BATTERY INSTALLATION

1. The

LED Outdoor Wall Sconce

requires 4 C cell batteries

(not included).

2. To access the battery compartment, remove the 2 thumb

screws from the top cover. Remove the top cover.

BATTERY INSTALLATION (CONTINUED)

3. Remove the battery compartment cover by squeezing

the two tabs on the cover inward and pulling up.

4. Install the 4 C cell batteries in the proper +/- polarity

orientation as shown in the illustration above. The

positive ends of the batteries should face the low battery

contacts and the negative ends of the batteries should

face the elevated spring terminals in the battery

compartment. If your unit includes a clear rubber spacer

between the two halves of the battery compartment,

please reinsert it between the two halves.

5. Reinstall the battery compartment cover by aligning the

tabs and pressing the battery compartment cover down

until the battery compartment cover clicks into place.

6. Reassemble the

LED Outdoor Wall Sconce

by replacing

the top cover and re-installing the two thumb screws.

Tighten the thumb screws by hand as tightly as possible

to ensure a waterproof seal.

Model # 4 9

page 1

LED Outdoor Wall Sconce

BATTERY-POWERED MOTION-ACTIVATED

Thumb Screw

Battery Compartment Cover

4 C Batteries

Squeeze tabs inward

Insert 4 C batteries

in the proper +/

orientation

Produkt Specifikationer

Mærke:	Maxsa
Kategori:	Ikke kategoriseret
Model:	43319-X

Har du brug for hjælp?

Hvis du har brug for hjælp til Maxsa 43319-X stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Maxsa Manualer

11 September 2024

11 September 2024

11 September 2024

11 September 2024

11 September 2024

11 September 2024

Maxsa Comfy Cruise 20014 Manual

30 Juli 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM LMC840 Manual

20 December 2025

IFM SMF150 Manual

20 December 2025

Ecler VEO-XCTRL4D Manual

20 December 2025

Brondell SMB-25 Manual

20 December 2025

Delta H71PB Manual

20 December 2025

Kichler 4D12V27 Manual

20 December 2025

JILONG KL-33F Manual

20 December 2025

Govee H7075 Manual

20 December 2025

Signature Hardware Greyfield 481138 Manual

20 December 2025

Aqprox appTPV00 Manual

20 December 2025