Mean Well DRA-40-24 Manual

Mean Well Ikke kategoriseret DRA-40-24

Læs gratis den danske manual til Mean Well DRA-40-24 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Mean Well DRA-40-24, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
Installaon Manual
Type：
：
：
：：DRA DIN rail power supply Series DRA-40, DRA-
（
（
（
（（ ：
：
：
：： 60）
）
）
））
DRA- - INPUT: -240VAC 0.8A 50/60Hz OUTPUT: V 3.34A 40 12 100 12
DRA- - INPUT: -240VAC 0.8A 50/60Hz OUTPUT: V 1.7A 40 24 100 24
DRA- - INPUT: -240VAC 1.3A 50/60Hz OUTPUT: V 5A 60 12 100 12
DRA- - INPUT: -240V 1.3A 50/60Hz OUTPUT: V 2.5A 60 24 100 AC 24
Introducon
DRA is a DIN rail power supply series featuring adjustable output current. Users are able to set its output current to
a range of 10% - 100% of rated current via 1-10Vdc, PWM signal or resistance. Like other Mean Well s DIN series, ’
they can be mounted on a TS35 Standard DIN rail.
Installaon
（ ）1 Always allow good venlaon clearances, 5mm le and right, 40mm above and 20mm below, around the unit
in use to prevent it from overheang. Also a 10-15 cm clearance must be kept when the adjacent device is a
heat source.
（ ）2 The appropriate mounng orientaon for the unit is vercal, the input terminals the bottom and output on at
the top. Mounng orientaons other than that, such as upside down, horizontal, or table-top mounng, is not
allowed.
（ ）3 Use copper wire only, and recommended wires are shown as below.
AWG
18
16
14
12
Rated Current of
Equipment (Amp)
7
10
15
20
Cross-secon of
Lead(mm2 )
0.8
1.3
2.1
3.3
Note Current each wire carries should be de-rated to 80% of the current suggested ：
above when using 4-6 wires connected to the unit.
Make sure that all strands of each stranded wire enter the terminal connecon and the screw terminals are
securely xed to prevent poor contact. If the power supply possesses mul-output terminals, please make
sure each contact is connected to wires to prevent too much current stress on a single contact.
（ ）4 Use wires that can withstand temperatures of at least 80°C, such as UL1007.
（ ）5 Recommended wire strapping length m (0.197 . is 5m ”)
（ ）6 Recommended screwdriver is 3 , sloed type.mm
（ ）7 The recommended torque seng for terminals(TB1) is 5 kgf‐cm (4.4 Lb‐in),
terminals(TB2) is 5 5 .8 kgf‐cm ( Lb‐in).
（ ）8 Each unit requires 0.15mA when dimming funcon is used. Please make sure your controller is capable of
driving the units.
Installaon Manual
3
1
2
（ ）9 Suggested fuse and maximum number of the DRA that can be connected to a circuit breaker at 230V are shown
as below.
Model
Fuse
Circuit breaker
C16
D 16
DRA- 40
T2.5A/L250V
11
21
DRA- 60
T2.5A/L250V
8
16
（ ）10 Mounng Instrucon ：
Mount as shown in gure only, with input terminals down, or else sucient cooling will not be possible.
Admissible DIN rail：TS35/7.5 or TS35/15
For rail fastening ：
（ ）a Tilt the unit slightly rearwards.
（ ）b Fit the unit over top hat rail.
（ ）c Slide it downward unl it hits the stop.
（ ）d Press against the bottom for locking.
（ ）e Shake the unit slightly to check the locking acon.
（ ）11 For other informaon about the products, please refer to www.meanwell.com for details.
Warning / Cauon !!
（ ）1Risk of electrical shock and energy hazard. All failure should be examined by a qualied technician. Please do
not remove the case of the power supply by yourself!
（ ）2Risk of electric arcs and electric shock (danger to life). Connecng both t primary and the secondary sides he
together is not allowed.
（ ）3Risk of burn hazard. Do not touch the unit in operaon and shortly aer disconnecon!
（ ）4 Risk of re and short circuit. The openings should be protected from foreign objects or dripping liquids.
（ ）5 Only install the unit in a polluon degree 2 environment (Note.1).
（ ）6 Please do not install the unit in places with high moisture or near the water.
（ ）7The maximum operang temperature is 45 for the DRA- - , for the DRA- -24, DRC-60A and °C 60 12 50°C 60
DRC-60B, for the DRA- -12/24, DRC-40A and DRC-40B, please do not install the unit in places with high 55°C 40
ambient temperature or near re source.
（ ）8 The FG ( ) must be connected to (Protecve Earth). PE
（ ）9 Output current and output waage must not exceed the rated value on its specicaon.
"Click"

Produkt Specifikationer

Mærke: Mean Well
Kategori: Ikke kategoriseret
Model: DRA-40-24

Har du brug for hjælp?

Hvis du har brug for hjælp til Mean Well DRA-40-24 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Mean Well Manualer

Mean Well

Mean Well LPF-40D-36 Manual

12 Januar 2025
Mean Well

Mean Well ELG-75-C700-3Y Manual

11 Januar 2025
Mean Well

Mean Well ELG-75-C500A-3Y Manual

11 Januar 2025
Mean Well

Mean Well LPF-40-54 Manual

11 Januar 2025
Mean Well

Mean Well HDR-15-5 Manual

5 Januar 2025
Mean Well

Mean Well ELP-75-12 Manual

3 Januar 2025
Mean Well

Mean Well DLP-04R Manual

3 Januar 2025
Mean Well

Mean Well QP-150C Manual

29 December 2024
Mean Well

Mean Well PWM-200-12 Manual

12 December 2024
Mean Well

Mean Well ELN-30-5 Manual

8 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Advantech

Advantech EAI-3100 Manual

30 Juli 2025
Deye

Deye SUN-M180G4-EU-Q0-I Manual

30 Juli 2025
Crestron

Crestron STIRP Manual

30 Juli 2025
Intellinet

Intellinet 790741 Manual

30 Juli 2025
Saris

Saris Edge 2-Bike Manual

30 Juli 2025
Advantech

Advantech ROM-3310 Manual

30 Juli 2025
Advantech

Advantech EKI-1751I Manual

30 Juli 2025
Advantech

Advantech ICR-1601W Manual

30 Juli 2025
C2G

C2G 29341 Manual

30 Juli 2025
Advantech

Advantech ITA-8120 Manual

30 Juli 2025