Mean Well NDR-75-24 Manual

Mean Well Ikke kategoriseret NDR-75-24

Læs gratis den danske manual til Mean Well NDR-75-24 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Mean Well NDR-75-24, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

Installaon Manual

 Type：

：

：：NDR DIN rail power supply Series NDR-75,

（

（（：

：

：： 120, 240, 480）

）

））

N - - INPUT: -240VAC 1.6A 50/60Hz OUTPUT: V 6.3A DR 75 12 100 12

N - - INPUT: -240VAC 1.6A 50/60Hz OUTPUT: V 3.2A DR 75 24 100 24

N - - INPUT: -240VAC 1.6A 50/60Hz OUTPUT: V 1.6A DR 75 48 100 24

N -120- INPUT: -240VAC 2.6A 50/60Hz OUTPUT: V A DR 12 100 12 10

N -120- INPUT: -240VAC 2.6A 50/60Hz OUTPUT: V 5A DR 24 100 24

N -120- INPUT: -240VAC 2.6A 50/60Hz OUTPUT: V 2.5A DR 48 100 48

NDR-240- INPUT: -240VAC 2.8A 50/60Hz OUTPUT: V A 24 100 24 10

NDR-240- INPUT: -240VAC 2.8A 50/60Hz OUTPUT: V 5A 48 100 48

NDR-480- INPUT: -240VAC 5.3A 50/60Hz OUTPUT: V A 24 100 24 20

NDR-480- INPUT: -240VAC 5.3A 50/60Hz OUTPUT: V A 48 100 48 10

 Introducon

NDR is a DIN rail power supply series with an economical price and slim design. Like other Mean Well DIN series, ’s

they can be mounted on a TS35 Standard DIN rail.

 Installaon

（）1 Always allow good venlaon clearances, 5mm le and right, 40mm above and 20mm below, around the unit

in use to prevent it from overheang. Also a 10-15 cm clearance must be kept when the adjacent device is a

heat source.

（）2 The appropriate mounng orientaon for the unit is vercal, the input terminals the bottom and output on at

the top. Mounng orientaons other than that, such as upside down, horizontal, or table-top mounng, is not

allowed.

（）3 Use copper wire only, and recommended wires are shown as below.

AWG

Rated Current of

Equipment (Amp)

10A

15A

20A

Cross-secon of

Lead(mm2 )

0.8

1.3

2.1

3.3

Note: Current each wire carries should be de-rated to 80% of the current suggested

above when using 5 or more wires connected to the unit.

Make sure that all strands of each stranded wire enter the terminal connecon and the screw terminals are

securely xed to prevent poor contact. If the power supply possesses mul-output terminals, please make

sure each contact is connected to wires to prevent too much current stress on a single contact.

（）4 Use wires that can withstand temperatures of at least 80°C, such as UL1007.

（）5 Recommended wire strapping length m (0.197 . is 5m ”)

（）6 Recommended screwdriver is 3 , sloed type.mm

Produkt Specifikationer

Mærke:	Mean Well
Kategori:	Ikke kategoriseret
Model:	NDR-75-24

Har du brug for hjælp?

Hvis du har brug for hjælp til Mean Well NDR-75-24 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Mean Well Manualer

Mean Well LPF-40D-36 Manual

12 Januar 2025

Mean Well ELG-75-C700-3Y Manual

11 Januar 2025

Mean Well ELG-75-C500A-3Y Manual

11 Januar 2025

Mean Well LPF-40-54 Manual

11 Januar 2025

Mean Well HDR-15-5 Manual

5 Januar 2025

Mean Well ELP-75-12 Manual

3 Januar 2025

Mean Well DLP-04R Manual

3 Januar 2025

Mean Well QP-150C Manual

29 December 2024

Mean Well PWM-200-12 Manual

12 December 2024

Mean Well ELN-30-5 Manual

8 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone 7800 Manual

11 December 2025

Kwikset 258 Manual

11 December 2025

Schlage F170 Manual

11 December 2025

Moen Align 7565EV Manual

11 December 2025

Energy Sistem ESG M3 Neon Manual

11 December 2025

ALNO MC10244 Manual

11 December 2025

JET TAK-ZX Manual

11 December 2025

Crosley Nashville CF1165 Manual

11 December 2025

Waterstone 1455 Manual

11 December 2025

Laica NE2015 Manual

11 December 2025