Mean Well RPD-75B Manual

Mean Well Ikke kategoriseret RPD-75B

Læs gratis den danske manual til Mean Well RPD-75B (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 7 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 4 anmeldelser. Har du et spørgsmål om Mean Well RPD-75B, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
Installation Manual
Type：
：
：
：： Medical Switching Power Supply
(1) Enclosed (Families: MSP)
(2) Modular (Families: MP, NMP)
(3) PCB (Families: MPS, MPD, MPT, MQ, RPS, RPD, RPT, RPTG, NEM, PM)
(4) Adaptor (Families: GSM, MES)
Installation
(1) Enclosed Type
(a) Before any installation or maintenance work, please disconnect your system from the utility.
Ensure that it cannot be re-connected inadvertently!
(b) Mounting orientations other than standard orientation or operate under high ambient
temperature may increase the internal component temperature and will require a de-rating in
output current. Please refer to the specification sheets to receive the optimum mounting
position and information about the de-rating curve.
(c) Fans or ventilation holes must be kept free from any obstructions. Also a 10-15 cm clearance
must be kept when the adjacent device is a heat source.
(d) Keep enough insulation distance between mounting screws and internal components of
Enclosed units. Please refer to case drawing on specifications to receive the maximum length of
mounting screw.
(e) Recommended wires of Enclosed units are shown as below.
AWG 18 16 14 12 10 8
Rated Current of
Equipment (Amp) 6A 6-10A 10-16A 16-25A 25-32A 32-40A
Cross-section of
Lead(mm2 ) 0.75 1.00 1.5 2.5 4 6
Note: The suggested maximum current above only suit for 1-4 strips, 5 or more
strips should not exceed 80% of current rating.
Make sure that all strands of each stranded wire enter the terminal connection and the screw
terminals are securely fixed to prevent poor contact.
(f) For other information about the products, please refer to www.meanwell.com for details.
(2) Modular Type
(a) Before any installation or maintenance work, please disconnect your system from the utility.
Ensure that it cannot be re-connected inadvertently!
(b) Mounting orientations other than standard orientation or operate under high ambient
temperature may increase the internal component temperature and will require a de-rating in
output current. Please refer to the specification sheets to receive the optimum mounting
position and information about the de-rating curve.
(c) Fans or ventilation holes must be kept free from any obstructions. Also a 10-15 cm clearance
must be kept when the adjacent device is a heat source.
(d) Keep enough insulation distance between mounting screws and internal components of
Modular units. Please refer to case drawing on specifications to receive the maximum length of
mounting screw.
(e) Recommended wires of Modular units are shown as below.
AWG 18 16 14 12 10 8
Rated Current of
Equipment (Amp) 6A 6-10A 10-16A 16-25A 25-32A 32-40A
Cross-section of
Lead(mm2 ) 0.75 1.00 1.5 2.5 4 6
Note: The suggested maximum current above only suit for 1-4 strips, 5 or more
strips should not exceed 80% of current rating.
Make sure that all strands of each stranded wire enter the terminal connection and the screw
terminals are securely fixed to prevent poor contact.
(f) For other information about the products, please refer to www.meanwell.com for details.
Installation Manual
(3) PCB Type
(a) Before any installation or maintenance work, please disconnect your system from the utility.
Ensure that it cannot be re-connected inadvertently!
(b) Mounting orientations other than standard orientation or operate under high ambient
temperature may increase the internal component temperature and will require a de-rating in
output current. Please refer to the specification sheets to receive the optimum mounting
position and information about the de-rating curve.
(c) Fans or ventilation holes must be kept free from any obstructions. Also a 10-15 cm clearance
must be kept when the adjacent device is a heat source.
(d) Recommended wires of PCB units are shown as below.
AWG 18 16 14 12 10 8
Rated Current of
Equipment (Amp) 6A 6-10A 10-16A 16-25A 25-32A 32-40A
Cross-section of
Lead(mm2 ) 0.75 1.00 1.5 2.5 4 6
Note: The suggested maximum current above only suit for 1-4 strips, 5 or more
strips should not exceed 80% of current rating.
Make sure that all strands of each stranded wire enter the terminal connection and the screw
terminals are securely fixed to prevent poor contact.
(e) At least 5mm insulation distance on the bottom of PCB units should be kept and a Mylar film
should be added between the units and the system. In addition, keep enough insulation
distance of 15mm around the PCB units.
(f) PCB units greater than 120W may require a forced air/fan for cooling. Please refer to
specifications to receive a minimum air intensity and air-flow direction.
(g) For other information about the products, please refer to www.meanwell.com for details.
(4) Adapter Type
(a) Before any installation or maintenance work, please disconnect your system from the utility.
Ensure that it cannot be re-connected inadvertently!
(b) Mounting orientations other than standard orientation or operate under high ambient
temperature may increase the internal component temperature and will require a de-rating in
output current. Please refer to the specification sheets to receive the optimum mounting
position and information about the de-rating curve.
(c) Fans or ventilation holes must be kept free from any obstructions. Also a 10-15 cm clearance
must be kept when the adjacent device is a heat source.
(d) Before attaching the DC plug of an adaptor to equipment, please unplug the adaptor from the
AC power and verify the unit is within the voltage and current rating on the equipment.
(e) Keep the linkage between the adaptor and its power cord tightly as well as connecting the DC
plug to equipment properly.
(f) Protect the power cord of adaptors from being trodden on or being squashed.
(g) An approved power cord of an adaptor should greater or equal to SVT, 3G×18AWG or H03VV-F,
3G×0.75mm2.
(h) If the final equipment is not used for long period of time, disconnect the equipment from
adaptors to avoid being damaged by voltage peaks or lightning strike.
(i) For other information about the products, please refer to www.meanwell.com for details.
User Manual
NMP series:
http://www.meanwell.com/webapp/product/search.aspx?prod=NMP1K2&pdf=Tk1QLUUucGRm&a=4

Produkt Specifikationer

Mærke: Mean Well
Kategori: Ikke kategoriseret
Model: RPD-75B

Har du brug for hjælp?

Hvis du har brug for hjælp til Mean Well RPD-75B stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Mean Well Manualer

Mean Well

Mean Well LPF-40D-36 Manual

12 Januar 2025
Mean Well

Mean Well ELG-75-C700-3Y Manual

11 Januar 2025
Mean Well

Mean Well ELG-75-C500A-3Y Manual

11 Januar 2025
Mean Well

Mean Well LPF-40-54 Manual

11 Januar 2025
Mean Well

Mean Well HDR-15-5 Manual

5 Januar 2025
Mean Well

Mean Well ELP-75-12 Manual

3 Januar 2025
Mean Well

Mean Well DLP-04R Manual

3 Januar 2025
Mean Well

Mean Well QP-150C Manual

29 December 2024
Mean Well

Mean Well PWM-200-12 Manual

12 December 2024
Mean Well

Mean Well ELN-30-5 Manual

8 September 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

ENTES

ENTES GEMO-10-DR-4G Manual

14 Juni 2025
Marshall

Marshall VAC-12SH Manual

14 Juni 2025
Rane

Rane MX 22 Manual

14 Juni 2025
Vulcan

Vulcan VCH88 Manual

14 Juni 2025
Fluke

Fluke SB140 Manual

14 Juni 2025
Blodgett

Blodgett BCT-101G Manual

14 Juni 2025
Rival

Rival 11570 Manual

14 Juni 2025
CDN

CDN MT1 Manual

14 Juni 2025
Savage Bros.

Savage Bros. FireMixer-14 Manual

14 Juni 2025
HMS Premium

HMS Premium STR01 Manual

14 Juni 2025