Mean Well RPS-65-7.5 Manual
Mean Well
Ikke kategoriseret
RPS-65-7.5
Læs nedenfor 📖 manual på dansk for Mean Well RPS-65-7.5 (4 sider) i kategorien Ikke kategoriseret. Denne guide var nyttig for 31 personer og blev bedømt med 4.4 stjerner i gennemsnit af 16 brugere
Side 1/4
Installation Manual
Type：
：
：
：： Medical Switching Power Supply
(1) Enclosed (Families: MSP)
(2) Modular (Families: MP, NMP)
(3) PCB (Families: MPS, MPD, MPT, MQ, RPS, RPD, RPT, RPTG, NEM, PM)
(4) Adaptor (Families: GSM, MES)
Installation
(1) Enclosed Type
(a) Before any installation or maintenance work, please disconnect your system from the utility.
Ensure that it cannot be re-connected inadvertently!
(b) Mounting orientations other than standard orientation or operate under high ambient
temperature may increase the internal component temperature and will require a de-rating in
output current. Please refer to the specification sheets to receive the optimum mounting
position and information about the de-rating curve.
(c) Fans or ventilation holes must be kept free from any obstructions. Also a 10-15 cm clearance
must be kept when the adjacent device is a heat source.
(d) Keep enough insulation distance between mounting screws and internal components of
Enclosed units. Please refer to case drawing on specifications to receive the maximum length of
mounting screw.
(e) Recommended wires of Enclosed units are shown as below.
AWG 18 16 14 12 10 8
Rated Current of
Equipment (Amp) 6A 6-10A 10-16A 16-25A 25-32A 32-40A
Cross-section of
Lead(mm2 ) 0.75 1.00 1.5 2.5 4 6
Note: The suggested maximum current above only suit for 1-4 strips, 5 or more
strips should not exceed 80% of current rating.
Make sure that all strands of each stranded wire enter the terminal connection and the screw
terminals are securely fixed to prevent poor contact.
(f) For other information about the products, please refer to www.meanwell.com for details.
(2) Modular Type
(a) Before any installation or maintenance work, please disconnect your system from the utility.
Ensure that it cannot be re-connected inadvertently!
(b) Mounting orientations other than standard orientation or operate under high ambient
temperature may increase the internal component temperature and will require a de-rating in
output current. Please refer to the specification sheets to receive the optimum mounting
position and information about the de-rating curve.
(c) Fans or ventilation holes must be kept free from any obstructions. Also a 10-15 cm clearance
must be kept when the adjacent device is a heat source.
(d) Keep enough insulation distance between mounting screws and internal components of
Modular units. Please refer to case drawing on specifications to receive the maximum length of
mounting screw.
(e) Recommended wires of Modular units are shown as below.
AWG 18 16 14 12 10 8
Rated Current of
Equipment (Amp) 6A 6-10A 10-16A 16-25A 25-32A 32-40A
Cross-section of
Lead(mm2 ) 0.75 1.00 1.5 2.5 4 6
Note: The suggested maximum current above only suit for 1-4 strips, 5 or more
strips should not exceed 80% of current rating.
Make sure that all strands of each stranded wire enter the terminal connection and the screw
terminals are securely fixed to prevent poor contact.
(f) For other information about the products, please refer to www.meanwell.com for details.
Installation Manual
(3) PCB Type
(a) Before any installation or maintenance work, please disconnect your system from the utility.
Ensure that it cannot be re-connected inadvertently!
(b) Mounting orientations other than standard orientation or operate under high ambient
temperature may increase the internal component temperature and will require a de-rating in
output current. Please refer to the specification sheets to receive the optimum mounting
position and information about the de-rating curve.
(c) Fans or ventilation holes must be kept free from any obstructions. Also a 10-15 cm clearance
must be kept when the adjacent device is a heat source.
(d) Recommended wires of PCB units are shown as below.
AWG 18 16 14 12 10 8
Rated Current of
Equipment (Amp) 6A 6-10A 10-16A 16-25A 25-32A 32-40A
Cross-section of
Lead(mm2 ) 0.75 1.00 1.5 2.5 4 6
Note: The suggested maximum current above only suit for 1-4 strips, 5 or more
strips should not exceed 80% of current rating.
Make sure that all strands of each stranded wire enter the terminal connection and the screw
terminals are securely fixed to prevent poor contact.
(e) At least 5mm insulation distance on the bottom of PCB units should be kept and a Mylar film
should be added between the units and the system. In addition, keep enough insulation
distance of 15mm around the PCB units.
(f) PCB units greater than 120W may require a forced air/fan for cooling. Please refer to
specifications to receive a minimum air intensity and air-flow direction.
(g) For other information about the products, please refer to www.meanwell.com for details.
(4) Adapter Type
(a) Before any installation or maintenance work, please disconnect your system from the utility.
Ensure that it cannot be re-connected inadvertently!
(b) Mounting orientations other than standard orientation or operate under high ambient
temperature may increase the internal component temperature and will require a de-rating in
output current. Please refer to the specification sheets to receive the optimum mounting
position and information about the de-rating curve.
(c) Fans or ventilation holes must be kept free from any obstructions. Also a 10-15 cm clearance
must be kept when the adjacent device is a heat source.
(d) Before attaching the DC plug of an adaptor to equipment, please unplug the adaptor from the
AC power and verify the unit is within the voltage and current rating on the equipment.
(e) Keep the linkage between the adaptor and its power cord tightly as well as connecting the DC
plug to equipment properly.
(f) Protect the power cord of adaptors from being trodden on or being squashed.
(g) An approved power cord of an adaptor should greater or equal to SVT, 3G×18AWG or H03VV-F,
3G×0.75mm2.
(h) If the final equipment is not used for long period of time, disconnect the equipment from
adaptors to avoid being damaged by voltage peaks or lightning strike.
(i) For other information about the products, please refer to www.meanwell.com for details.
User Manual
NMP series:
http://www.meanwell.com/webapp/product/search.aspx?prod=NMP1K2&pdf=Tk1QLUUucGRm&a=4
Produkt Specifikationer
| Mærke: | Mean Well |
| Kategori: | Ikke kategoriseret |
| Model: | RPS-65-7.5 |
Har du brug for hjælp?
Hvis du har brug for hjælp til Mean Well RPS-65-7.5 stil et spørgsmål nedenfor, og andre brugere vil svare dig
Ikke kategoriseret Mean Well Manualer
12 Januar 2025
11 Januar 2025
11 Januar 2025
11 Januar 2025
5 Januar 2025
3 Januar 2025
3 Januar 2025
29 December 2024
12 December 2024
8 September 2024
Ikke kategoriseret Manualer
- Ikke kategoriseret Mitsai
- Ikke kategoriseret Barazza
- Ikke kategoriseret Roswell
- Ikke kategoriseret Crest Audio
- Ikke kategoriseret Kendau
- Ikke kategoriseret ARRI
- Ikke kategoriseret Nureva
- Ikke kategoriseret Aspes
- Ikke kategoriseret StrikeMaster
- Ikke kategoriseret Contemporary Research
- Ikke kategoriseret Denver
- Ikke kategoriseret Omnitronic
- Ikke kategoriseret Pentatech
- Ikke kategoriseret AYA
- Ikke kategoriseret Cressi
Nyeste Ikke kategoriseret Manualer
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025
31 Maj 2025