Mean Well RSD-100C-24 Manual


Læs gratis den danske manual til Mean Well RSD-100C-24 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 27 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 14 anmeldelser. Har du et spørgsmål om Mean Well RSD-100C-24, eller vil du spørge andre brugere om produktet?

Side 1/3
Installaon Manual
Type
DC-DC converter Families PSD, SD, RSD
Introducon
A DC-DC converter is a device used to convert a DC source from one voltage level to another. Mean Well’s DC-DC
converters equipped with internal EMI lter stage that possess the required EMC performance.
Installaon
( )1Before commencing any installaon or maintenance work, please disconnect your system from the
ulity. Ensure that it cannot be re-connected inadvertently!
( )2For PCB type, at least 5mm insulaon distance around the unit should be kept.
( )3Allow good venlaon for the unit in use to prevent it from overheang. Also, a 10-15 cm clearance
must be kept when the adjacent device is a heat source.
( )4Mounng orientaons other than standard orientation or operate under high ambient temperature
may increase the internal component temperature and will require a de-rang in output current.
Please refer to the specicaon sheets to receive opmum mounng posion and informaon the
about the -rang curve.de
( )5Recommended input/output wires are shown as below.
AWG
18
16
14
12
10
8
Rated Current of
Equipment (Amp)
6A
6-10A
10- 16A
16 25A-
25 32A-
32 40A-
Cross-secon of
Lead(mm2 )
0.75
1.00
1.5
2.5
4
6
Note: Current each wire carries should be de-rated to 80% of the current
suggested above when using 5 or more wires connected to the unit.
( )6For PCB type, compable mang housing please refers to the specicaons
( )7 For enclosed type, make sure that all strands of each stranded wire enter the terminal connecon and the
screw terminals are securely xed to prevent poor contact.
( )8 For other informaon about the products, please refer to www.meanwell.com for details.
Warning / Cauon !!
( )1Risk of electrical shock and energy hazard. All should be examined by a qualied technician. failure
Please do not try to x the converter by yourself!
( )2Risk of irreparable damage. Do not reverse polarity, both input and output.
( )3Please do not install converters in places with high moisture or near the water.
( )4Please do not install converters in places with high ambient temperature or near re source. Please
refer to the specicaons about the maximum ambient temperature limitaons.
( )5Output current and output waage must not exceed the rated values on specicaons.
( )6The ground (FG) must be connected to earth ground.
( )7For system consideraons, PCB and enclosed type converters may require an addional inrush
current liming circuit to suppress high inrush current surges. If you are uncertain about that circuit,
contact Mean Well.
( )8 All of an WellMe ’s converters are designed in accordance with EMC regulaons and the related test reports
are available by request. Since they are belong to component power supplies and will be installed inside
system enclosure, when they are integrated into a system, the EMC characteriscs of the end system must be
re-veried again.
Installaon Manual
Manufacturer
MEAN WELL ENTERPRISES Co., LTD.
No.28, Wuquan 3rd Rd., Wugu Dist.,
New Taipei City 24891, Taiwan
Tel: +886-2-2299-6100
Web: www.meanwell.com
Branch Oce
China
MEAN WELL (GUANGZHOU)
ENTERPRISES Co., LTD.
2F, A Building, Yuean lndustry Park,
Huangcun,Dongpu Yown, Tianhe
District, Gungzhou, China
Post Code:510660
Tel: +86-20-2887-1200
Web: www.meanwell.com.cn
U.S.A.
MEAN WELL USA, INC.
44030 Fremont Blvd., Fremont,
CA 94538, U.S.A.
Tel: +1-510-683-8886
Web: www.meanwellusa.com


Produkt Specifikationer

Mærke: Mean Well
Kategori: Ikke kategoriseret
Model: RSD-100C-24

Har du brug for hjælp?

Hvis du har brug for hjælp til Mean Well RSD-100C-24 stil et spørgsmål nedenfor, og andre brugere vil svare dig