Metra 44-PW22 Manual

Metra Bilmonteringssæt 44-PW22

Læs gratis den danske manual til Metra 44-PW22 (8 sider) i kategorien Bilmonteringssæt. Denne vejledning er vurderet som hjælpsom af 9 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 5 anmeldelser. Har du et spørgsmål om Metra 44-PW22, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/8

AW-PW22

Fully Automatic

AM/FM Power Antenna

Installation Instruction

MOTOR

ASSEMBLY

METAL STRAP

DRAIN TUBE

MAST TUBE

RETAINER

ASKETSGASKETS

IXED ANGLE BASES

OUNTING SPACER

OUNTING NUT

OUNTING WASHER

“ (25mm) HOLE

LUSH ADJUSTABLE

NGLE BASE

3’’

’’

15’’

3’’

30’’

7/8” / (22mm) HOLE

OAXIAL CABLE

NDERSIDE

OF FENDER

5/8” / 16mm HOLE

ELECTRICAL

IRES

FIG. 1

This antenna is designed for optimum performance for either AM or

FM bands. The antenna is raised or lowered by operating the radio

on/of

f switch.

) Disassemble the mounting base and save the parts, they may be

used with the installation of the new antenna.

) Remove old antenna from below fender.

) To avoid cutting car wiring, you may want to cut the connector off

f the old antenna removed from the car, attaching the new anten-

na wiring to the old connector wires and directly plug into car wiring.

. NEW ANTENNA INSTALLATION:

or first time antenna installations:

A) Use original factory hole or select a location on the front or back

ender of car for mounting antenna. In selecting the location, make

sure the underside of the fender is free of any obstruction such as

weld beads, braces, gussets and sub-fender.Also, be sure that suf-

icient clearance is available under fender to house the antenna,

approximately 11-1/2” / 29cm.

) Six mounting bases are provided with the antenna. Five fixed

angle and one adjustable angle flush mount base.

(See Figure 1).

C) Remove the installed flush mounting base from new antenna.

elect the proper base with correct angle for fender (as shown in

figure

1) or reuse original mounting base previously re

moved from

old antenna.

NOTE: The five fixed angle bases require a 7/8” /

22mm hole. The adjustable angle flush base requires a 1”

25mm hole.

D) A 1/8” / 3mm pilot hole should be drilled, then enlarged with a

hole saw or drill bit to the proper size.

E) Remove all burrs, paint, road dirt or undercoating from around the

underside of the hole.

F) Install the antenna from the underside of the fender and assem-

ble the base above the fender according to

Figure 1. BE SURE THE

RETAINER RESTS EVENLY ON THE UNDERSIDE OF THE FENDER

TO ALLEVIATE ANY POSSIBLE DAMAGE TO THE VEHICLE. Align

the mast vertically by slightly tightening the antenna mounting nut

while adjusting the mast to be vertical.

G) To prevent movement and maintain the desired angle, secure the

bottom of the motor assembly with the supplied perforated strap.

Holes are provided with the strap to accommodate various mount-

ing positions. It may be necessary to bend the strap to conform to

the fit of the antenna and car

. Be sure the antenna retainer is

grounded to the underside of the

fender and the black ground wire is gr

ounded properly to the vehi-

cle chassis. If the retainer and ground wire are not properly ground-

ed,

THE ANTENNA WILL NOT FUNCTION.

H) With the bottom of the antenna motor assembly secured, the

mast at the desired angle and the retainer resting evenly on the

underside of the fender, tighten the mounting nut firmly to secure

the entir

e antenna assembly

. Do not tighten the nut excessively as

this may strip or break the mounting threads or damage contact

spring and cause improper antenna operation.

I) Attach the drain lube to the bottom of the motor assembly and

route to the outside of the car. Avoid any kinks or bends in the tube

that may r

estrict drainage.

(as shown in figur

e 1.)

For new antenna installations:

J) Route electrical wiring and coaxial cable into the dash ar

ea of the

vehicle interior as shown in

Figur

e 2.

(44-PWEC157 extension

cable may be required). A 5/8” / 16mm hole may be required in the

interior panel when routing wire from front fender. If possible, avoid

outing coaxial cable into engine compartment. The electrical noise

found in this area may be transmitted into the antenna wiring.

Prior to installing the antenna, read the

entire installation instructions.

May require an extension cable depending on vehicle or an anten-

na adapter cable for many 1995-up For

d, 1988-up GM and some

imports.

1.REPLACEMENT OF EXISTING POWER ANTENNA,

REMOVING OLD ANTENNA.

A) Gain access to the underside of the fender ar

ea through the

trunk, fender splash panel, etc.

B) Remove mounting bracket, drain tube, electrical wire and anten-

na coaxial cable.When removing electrical wires and coaxial cable

from the antenna, follow to the closest connector and disconnect.

DO NOT CUT COAXIAL CABLE.

EPRODUCTION OF EDITORIAL OR PICTORIAL CONTENT IS

TRICTLY PROHIBITED WITHOUT WRITTEN CONSENT OF

METRA/ROADWORKS

Produkt Specifikationer

Mærke:	Metra
Kategori:	Bilmonteringssæt
Model:	44-PW22

Har du brug for hjælp?

Hvis du har brug for hjælp til Metra 44-PW22 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Bilmonteringssæt Metra Manualer

Metra 108-FD5CH Manual

7 Oktober 2025

Metra 108-FD8CH Manual

7 Oktober 2025

Metra 99-5854B Manual

7 Oktober 2025

Metra 99-5852CH Manual

7 Oktober 2025

Metra XSVI-6522-NAV Manual

6 Oktober 2025

Metra 95-8907HD Manual

6 Oktober 2025

Metra 95-7424 Manual

6 Oktober 2025

Metra 99-8259B Manual

6 Oktober 2025

Metra 95-8733B Manual

6 Oktober 2025

Metra 99-8208 Manual

6 Oktober 2025

Bilmonteringssæt Manualer

Nyeste Bilmonteringssæt Manualer

Griffin iTrip Auto HandsFree Manual

4 November 2025

American International NDK746 Manual

8 Oktober 2025

BURY UNI Take&Talk Manual

30 September 2025

Havis PKG-PSM-101 Manual

12 September 2025

Havis PKG-PSM-120 Manual

12 September 2025

Havis C-HDM-142 Manual

12 September 2025

Havis C-DMM-118 Manual

11 September 2025

Havis C-HDM-140 Manual

11 September 2025

Havis C-HDM-146 Manual

11 September 2025

Havis PKG-PSM-140 Manual

11 September 2025