Metra CHTO-03 Manual

Metra Bilmonteringssæt CHTO-03

Læs gratis den danske manual til Metra CHTO-03 (2 sider) i kategorien Bilmonteringssæt. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Metra CHTO-03, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
CHRYSLER CAN BUS INTERFACE
©Copyright 2004-2010 Metra Electronics Corporation
1-800-221-0932
www.metraonline.com
CHTO-03
INSTALLATION INSTRUCTIONS
*IMPORTANT WARNING
THIS PRODUCT INCLUDES INSTRUCTIONS FOR INSTALLATION
WHICH MUST BE CAREFULLY FOLLOWED. THE INSTRUCTIONS
INSTALLER IS CAPABLE OF COMPLETING THESE TYPE OF
ELECTRONIC INSTALLATIONS. IF YOU ARE UNCLEAR AS TO
WHAT YOU ARE INSTRUCTED TO DO OR BELIEVE THAT YOU DO
NOT UNDERSTAND THE INSTRUCTIONS SO AS TO PROPERLY
AND SAFELY COMPLETE THE INSTALLATION YOU SHOULD
CONSULT A TECHNICIAN WHO DOES HAVE THIS KNOWLEDGE
AND UNDERSTANDING.
FAILURE TO FOLLOW THESE INSTRUCTIONS CAREFULLY
AND TO INSTALL THE INTERFACE AS DESCRIBED COULD
CAUSE HARM TO THE VEHICLE OR TO SAFETY SYSTEMS
ON THE VEHICLE. INTERFERENCE WITH CERTAIN SAFETY
SYSTEMS COULD CAUSE HARM TO PERSONS AS WELL.
IF YOU HAVE ANY QUESTIONS IN THIS REGARD PLEASE
CALL THE HELP LINE OR THE METRA AT 1-800-221-0932
FOR ASSISTANCE.
CHTO-03 CHTO-03
* READ IMPORTANT WARNING INSIDE
BEFORE ATTEMPTING ANY INSTALLATION
THE CHTO-03 IS DESIGNED TO BE USED WITH
VEHICLES THAT HAVE A FACTORY AMPLIFIED
SYSTEM. THE CHTO-03 WILL PROVIDE A 12-VOLT
SWITCHED WIRE FOR PROPER RADIO OPERATION.
THE CHTO-03 NOW PROVIDES MUTE, PARKING
BRAKE, VSS OR SPEED SENSE, AND A REVERSE
OUTPUT TO MAKE INSTALLING AN AFTERMARKET
NAVIGATIONAL RADIO SIMPLER AND LESS TIME
COMSUMING.
Cutting Tool • Tape • Crimping Tool • Connectors
TOOLS REQUIRED FOR INSTALLATION
When using the CHTO-03 with a radio that has a high audio
pre-out voltage, usually greater than 2 volts, the audio signal
may become distorted. To resolve this follow these steps:
1. Make sure the ignition is turned to the “off” position.
2. Disconnect both of the harnesses from the CHTO-03.
3. Locate the potentiometer next to the 14-pin connector at
the end of the CHTO-03.
4. Taking a small flat headed screwdriver, turn the
potentiometer counter-clockwise to lower the input
level going to the factory amplifier.
5. After making the adjustment reconnect the wire harnesses.
4
REV. 03-17-11 INSTCHTO-03
POTENTIOMETER
AUDIO LEVEL
ADJUSTMENT
INTERFACE COMPONENTS
• CHTO-03 • 14-PIN HARNESS WITH RCA’S
• (2) 12-PIN HARNESSES TO 22-PIN CHRYSLER HARNESSES
AUDIO LEVEL CONTROL
CONNECTIONS TO BE MADE ON THE
14-PIN HARNESS
1. Connect the blue/white wire to the radio’s amplifier turn-on wire.
2. Connect the red wire to the radio’s Igniton or accessory wire.
3. Connect the RCA cables to the radio’s RCA outputs. If no RCA
outputs are available, use the Metra line output converter, part #
ALOC648, (SOLD SEPARATELY).
4. The white RCA goes to the left front RCA output of the radio.
5. The gray RCA goes to the right front RCA output of the radio.
6. The green RCA goes to the left rear RCA output of the radio.
7. The purple RCA goes to the right rear RCA output of the radio.
The following wires on the 14-pin harness are for the
aftermarket radios that have navigation built in:
Connect the brown wire to the mute wire of the aftermarket radio.
Connect the green wire to the parking brake wire of the
aftermarket radio.
Connect the blue/pink wire to the VSS or speed sense wire of the
aftermarket `radio.
Connect the green/purple wire to the reverse wire of the
aftermarket radio.
When completed, plug the 14-pin harness into the CHTO-03.
INSTALLING THE CHTO-03
1. With all connections completed to the aftermarket radio, plug the
22-pin connector into the vehicle’s corresponding wiring harnesses.
2. Cycle the key by turning the ignition on then back off, then back on
again to test the radio.
TESTING THE CHTO-03
1. Turn the ignition on then the radio to verify the radio works. Check
balance and fader controls for proper operation. If controls are
backwards, check to see if the RCA’s are in the correct location.
2
1
CHTO-03
WIRING UP THE CHTO-03
* Important: Before beginning any of the following, disconnect the
negative battery terminal to prevent accidental short circuit.
* NOTE: THE ACCESSORY POWER SOURCE OF MOST ALL
CHRYLSER VEHICLES KEEPS THE RADIO ON UNTIL ONE OF
THE DOORS IS OPENED. THIS IS CALLED R.A.P. (RETAINED
ACCESSORY POWER). THE CHTO-03 IS DESIGNED TO
RETAIN THIS FEATURE.
* NOTE: THE VEHICLES IGNITION SWITCH MUST BE IN THE OFF
POSITION BEFORE PLUGGING THE CHTO-03 MODULE IN.
ALSO THE KEY MUST BE CYCLED AT A MEDIUM PACE AT
LEAST TWO TIMES BEFORE BEGINNING TESTING.
CONNECTIONS TO BE MADE ON THE
22-PIN HARNESS:
1. Connect the yellow wire to the radio’s 12v battery or memory wire.
2. Connect the black wire to the radio’s ground wire.
3. Connect the orange wire to the radio’s illumination wire. If wire is
not present, tape up wire.
4. For the Caliber only, connect the blue/white wire to the
blue/white wire in the 14-pin harness, which connects to the
radio’s amplifier turn-on wire.
3
APPLICATIONS
Metra recommends MECP
certified technicians.
KNOWLEDGE IS POWER
Enhance your installation and fabrication skills by
enrolling in the most recognized and respected
mobile electronics sch ol in our industry.o
Log onto www.installerinstitute.com or ca l l
800-354-6782 for more information and take steps
towa a better tomorrord w.
CHRYSLER
200 2011
300 2008-UP
ASPEN 2008-09
SEBRING 2007-10
TOWN & COUNTRY 2008-UP
DODGE
AVENGER 2008-UP
CALIBER 2009-10
CHALLENGER 2009-UP
CHARGER 2008-10
DAKOTA 2008-UP
DURANGO 2008-UP
GRAND CARAVAN 2008-10
JOURNEY 2009-UP
MAGNUM 2008-09
NITRO 2007-UP
RAM 1500 2009-UP
RAM 2500/3500 2010-UP
JEEP
COMMANDER 2008-2010
COMPASS 2009-UP
GRAND CHEROKEE 2008-UP
LIBERTY 2008-UP
PATRIOT 2009-UP
WRANGLER 2007-UP
MITSUBISHI
RAIDER 2008-09

Produkt Specifikationer

Mærke: Metra
Kategori: Bilmonteringssæt
Model: CHTO-03

Har du brug for hjælp?

Hvis du har brug for hjælp til Metra CHTO-03 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Bilmonteringssæt Metra Manualer

Metra

Metra 99-8905B Manual

12 September 2025
Metra

Metra 99-8220CHG Manual

27 August 2025
Metra

Metra 99-5026 Manual

25 August 2025
Metra

Metra 107-TO8HG Manual

21 August 2025
Metra

Metra 95-7332 Manual

21 August 2025
Metra

Metra 95-7605A Manual

21 August 2025
Metra

Metra 109-TO8HG Manual

21 August 2025
Metra

Metra 95-7641B Manual

21 August 2025
Metra

Metra 95-3004 Manual

21 August 2025
Metra

Metra 99-5814S Manual

21 August 2025

Bilmonteringssæt Manualer

Nyeste Bilmonteringssæt Manualer

BURY

BURY UNI Take&Talk Manual

30 September 2025
Havis

Havis PKG-PSM-101 Manual

12 September 2025
Havis

Havis PKG-PSM-120 Manual

12 September 2025
Havis

Havis C-HDM-142 Manual

12 September 2025
Havis

Havis C-DMM-118 Manual

11 September 2025
Havis

Havis C-HDM-140 Manual

11 September 2025
Havis

Havis C-HDM-146 Manual

11 September 2025
Havis

Havis PKG-PSM-140 Manual

11 September 2025
Havis

Havis C-HDM-415 Manual

11 September 2025
Havis

Havis PKG-PSM-102 Manual

11 September 2025