Microchip HV2803 Manual


Læs gratis den danske manual til Microchip HV2803 (32 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 14 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 7.5 anmeldelser. Har du et spørgsmål om Microchip HV2803, eller vil du spørge andre brugere om produktet?

Side 1/32
2017-2019 Microchip Technology Inc. DS20005721C-page 1
HV2803/HV2903/HV2904
Features
32-Channel, High-Voltage Analog Switch
No High-Voltage Supplies Required
32-Channel, Single-Pole, Single-Throw (SPST)
Individual Switching or Bank Switching
3.3V CMOS Input Logic Level
66 MHz Data Shift Clock Frequency
Silicon-on-Insulator (SOI) High-Voltage
Technology for High Performance
Standby mode for Low-Power Dissipation
Low-Parasitic Capacitance
DC to 50 MHz Analog Small-Signal Frequency
200 kHz to 50 MHz Large-Signal Frequency
-70 dB Typical Off Isolation at 5.0 MHz
Excellent Noise Immunity
Cascadable Serial Data Register with Latches
Integrated Bleed Resistors on the Outputs (both
sides for HV2903, one side for HV2904)
Applications
Medical Ultrasound Imaging
Nondestructive Testing (NDT) Metal Flaw
Detection
Piezoelectric Transducer Drivers
Inkjet Printer Heads
Optical MEMS Modules
General Description
The HV2803/HV2903/HV2904 devices are low harmonic
distortion, low charge injection, 32-channel, high-voltage
analog switches without high-voltage supplies. They are
intended for use in applications requiring high-voltage
switching controlled by low-voltage control signals, such
as medical ultrasound imaging, driving piezoelectric
transducers and printers.
The HV2903 device has integrated bleed resistors at
both sides of the switches; the HV2904 device has
bleed resistors at one side only, while the HV2803
device has no bleed resistors. The bleed resistor
eliminates voltage build-up on capacitive loads, such
as piezoelectric transducers.
The HV2803/HV2903/HV2904 devices have two
modes of operation determined by the MODE pin input.
MODE input high enables an individual Switching
mode of 32-channel SPST switches and MODE input
low enables a Bank Switching mode of 16-Pole
Double-Throw (16PDT) switches to support bank
switching for probe selection.
The devices require only ±6V or ±5V low-voltage
supplies and no high-voltage supplies. However, all the
analog switches can transmit ±100V high-voltage pulses.
Package Type
1 2 3 4 5 6 7 8 9 10 11 12 13
A
B
C
D
E
F
G
H
P
J
K
L
M
14
N
HV2803/HV2903/HV2904
12 x 12 x 1.20 mm TFBGA
(Top View*)
* See Section 2.0 “Package Pin Configuration
and Function Description”.
No High-Voltage Bias, Low Harmonic Distortion,
32-Channel, High-Voltage Analog Switch
HV2803/HV2903/HV2904
DS20005721C-page 2 2017-2019 Microchip Technology Inc.
Block Diagram
Level
Shifters
VDD
VSS
Output
Switches SW0A
SW0B
SW1A
SW1B
SW2A
SW2B
SW30A
SW30B
SW31A
SW31B
Bleed
Resistors
RGND
HV2903 has bleed resistor at SWxA and SWxB
HV2904 has bleed resistor at SWxA only
GND
VLL
CLR
LE/EN
CLK
DIN/AB
DOUT
32-Bit
Shift
Register
and
Latches
(Mode = H,
Individual
Switching Logic)
Logic
Control
and
Latches
(Mode = L,
Bank Switching
Logic)
EN
A/B
MODE
STBY


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: HV2803

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip HV2803 stil et spørgsmål nedenfor, og andre brugere vil svare dig




Ikke kategoriseret Microchip Manualer

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer