Microchip HV9982DB1 Manual

Microchip Ikke kategoriseret HV9982DB1

Læs gratis den danske manual til Microchip HV9982DB1 (11 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 34 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 17.5 anmeldelser. Har du et spørgsmål om Microchip HV9982DB1, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/11
Supertex inc.
Supertex inc.
www.supertex.com
HV9982DB1
Doc.# DSDB-HV9982DB1
A032913
General Description
The HV9982DB1 is a three channel boost LED driver
demoboard using Supertex’s HV9982 LED Driver IC. The
LED driver can be used to drive RGB or multi channel
white LEDs from a 24V input. The LED string current can
be adjusted up to a maximum of 100mA. The demoboard
has good current matching between strings and an excellent
PWM dimming response, making it ideal for LED backlight
applications.
The HV9982DB1 uses the HV9982 LED driver IC to drive
three discontinuous conduction mode boost converters
at a 500kHz switching frequency. The clocks of the three
channels are phase shifted to provide ripple cancellation at
the input and thus reducing the input capacitor requirements.
The output current level can be adjusted using an external
voltage source at the REF terminal.
The HV9982DB1 includes hiccup mode protection for both
short circuit and open circuit conditions to ensure that it
recovers from a momentary fault condition. It also enables
the board to survive prolonged fault conditions without any
damage to both the driver as well as the LEDs.
The HV9982DB1 also includes an on-board PWM generator
for analog control for PWM dimming (for backward
compatibility with CCFL controllers). This feature enables
the user to PWM dim the driver with a 0 - 2.0V analog signal
input and helps to achieve zero LED current with an analog
dimming input
Connection Diagram
Three Channel
LED Driver Demoboard
Specications
Parameter Value
Input voltage 24V ± 10%
LED string voltage (all channels) 35V – 80V
LED current (all channels) 100mA (max)
Switching frequency of the
converter at FCLK = 6.0MHz 500kHz
External frequency at CLK pin 6MHz
Current matching between
channels ≤ ± 3%
Typical full load efciency 90%
PWM dimming
rise and fall times ≤1μs
PWM dimming frequency
(for analog control of PWM
dimming)
480Hz (typ)
Shutdown mode current ≤ 600μA
Typical IDD current
(for all three channels) 12mA (VDD = 8V)
Open LED drotection Included; hiccup-mode
Output short circuit protection Included; hiccup-mode
Hiccup time 1ms (typ)
24V DC source
0 - 0.5V
DC source
6MHz clock
(TTL compatible)
- +
+
-
2
HV9982DB1
Supertex inc.
www.supertex.com
Doc.# DSDB-HV9982DB1
A032913
Connections
Pin Connection
VIN This terminal is the positive input of the 24V supply for the boost converters. It is also the input for the
internal regulator of the IC.
GND, GND1 These terminals are the return paths for all the input voltages and signals for the demoboard. All voltages
and signals (other than the output terminals) should be referenced to these two terminals.
VDD
This terminal is connected to the VDD pins of the IC. When left unconnected, the voltage at this terminal
will be regulated to 7.75V by the internal regulator of the HV9982. To supply the IC with an external VDD
supply, connect an 8-10V source to this terminal.
EN This terminal can be used to shut down the IC. Connecting this terminal to GND will cause the IC to go
into a standby mode and draw less than 500μA.
CLK
This terminal is the clock input to the IC. A TTL compatible 6MHz clock should be connected to this ter-
minal. In case an on-board clock is preferred, a 6MHz xed frequency oscillator can be soldered in at U2
(please refer to BOM for the part number).
5V
A 5.0V, 50mA source needs to be connected to this point, if an on-board clock is used. This provides
the power required for the xed frequency oscillator at U2. This terminal can be left open if an external
6.0MHz clock is used.
REF This terminal is the control input for adjusting the LED current level. A 0 – 500mV voltage source should
be connected to this terminal.
S1, S2
These two switches on the demoboard control the PWM dimming function. They can be used to enable
either direct PWM dimming of the channels using an external TTL signal or analog control of PWM dim-
ming using a 0-2.0V analog signal. The control logic for these switches is given in Table 1.
PWMD1-3 These terminals are the PWM dimming inputs. The inputs can be either TTL compatible square wave
signals or 0-2.0V analog signals depending on the conguration of switches S1 and S2.
VO+1-3 The anodes of the LED strings should be connected to these terminals as shown in the connection dia-
gram.
VO- 1-3 The cathodes of the LED strings should be connected to these terminals as shown in the connection
diagram.
SKIP This terminal is connected to the hiccup timing capacitor and can be used to measure the hiccup time.
SYNC
This terminal can be used to synchronize the internal PWM ramp to an external clock. A TTL compatible,
350 – 400Hz external clock with a pulse width less than 2% can be applied at this terminal to synchronize
the internal ramp to the external clock.
Table 1 : Truth Table for S1 and S2
S1 S2 PWMD Output
LO LO The output will follow PWMD input signal
LO HI
HI LO Input DC zero volt corresponds to 100% duty cycle output
HI HI Input DC two volt corresponds to 100% duty cycle output

Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: HV9982DB1

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip HV9982DB1 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Microchip Manualer

Microchip

Microchip ATmega1281 Manual

19 Juli 2025
Microchip

Microchip ATtiny461 Manual

19 Juli 2025
Microchip

Microchip ATxmega128D3 Manual

19 Juli 2025
Microchip

Microchip ATxmega128D4 Manual

19 Juli 2025
Microchip

Microchip ATTINY28 Manual

19 Juli 2025
Microchip

Microchip ATTINY861 Manual

19 Juli 2025
Microchip

Microchip ATmega1280 Manual

19 Juli 2025
Microchip

Microchip ATtiny84A Manual

19 Juli 2025
Microchip

Microchip ATmega645P Manual

19 Juli 2025
Microchip

Microchip ATmega16A Manual

19 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Navman

Navman MiVue Smartbox 3 Manual

1 August 2025
Navman

Navman MiVue 850 Manual

1 August 2025
Navman

Navman MiVue 690 Manual

1 August 2025
Navman

Navman MiVue 145 GPS TAG Manual

1 August 2025
Navman

Navman MY30 Manual

1 August 2025
Tripp Lite

Tripp Lite SPS610HGRA Manual

1 August 2025
AEG

AEG E1WYHSK1 Manual

1 August 2025
Thermaltake

Thermaltake Pacific R1 Plus Manual

1 August 2025
Olivetti

Olivetti d-Copia 4523MFplus Manual

1 August 2025
Gossen

Gossen GL SpectroSoft Manual

1 August 2025