Microchip IS1870 Manual


Læs gratis den danske manual til Microchip IS1870 (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Microchip IS1870, eller vil du spørge andre brugere om produktet?

Side 1/3
BM70/71 & IS1870/71 rmware 2.03 Release Notes Fi July 22, 20 20
IS1870/71 & BM70/71 Firmware 2.03
Release Notes
1 Overview
Firmware version 2.0 is a maintenance release for IS1870, IS1871, BM70, and BM71. Firmware
version 2.0 adds new features/ removes limitations in previous release 1.11. This firmware is made
available on Microchips web site for existing ICs and modules.
1.1 Resolved Issues
Fixed read ADC command problem for temperature detection.
Fixed Sweyntooth BLE vulnerabilities in LL, SMP and L2CAP layers.
Fixed disconnection issue with Xiaomi Mi 10 Pro Phone.
Fixed MPAF OTA update UI fail issue.
Fixed HID over GATT issue.
Fixed an issue where pairing fails in Multilink scenario with reason DHKey failure check.
Fixed Instant Pass Issue for Multilink scenarios (LL_STATUS_ERROR_INSTANT_PASSED/0x28)
IOP Pairing fail issue with Samsung S8 Verizon variant.
Write to Flash is enabled for few manual pattern commands like WRITE DEVICE NAME
command (0x08).
Fixed issue where AutoPattern Mode BM70 outputs manual mode data from UART.
Fixed an issue where the application always starts passive scan irrespective of whether scan
type is set to passive or active.
Fixed an issue where the SCAN_RES is displayed as ADV_IND.
Fixed an issue where ADC return value was shown incorrectly.
Fixed an issue where connection was getting terminated due to MIC failure in Multilink scenario.
1.2 New Features
BLE Data Length Extension to max 251 bytes.
Maximum BLE ATT MTU size is 247 bytes
AFH channel map adjust automatically when BLEDK3 is Central role ed
Supports LE privacy feature v1.1 (disabled by default in UI settings)
Enhance data transmission throughput in Auto pattern mode
Supports following in auto pattern mode
o BLEDK3 v2.0 to be GAP Central role
o It allows two nearby BLEDK3 v2.0 devices with auto pattern to establish BLE link
BM70/71 & IS1870/71 rmware 2.03 Release Notes Fi July 22, 20 20
automatically
Multi-link/Multi-role capability in Manual mode
o Maximum 4 BLE links can exist simultaneously (with Multi-link device as Central for all
links). When the multi-link device is in Peripheral role for at least one link the maximum
number of links is limited to 2. Below shows the valid combination of multi-link possibility
BLE multi-link
BLEDK3 v2.0 Role
Other peer devices
Note
Case 1
One BLE link
Central
Peripheral
OK
Peripheral
Central
OK
Case 2
Two BLE links
Central
Two independent
Peripherals
OK
Peripheral
Two independent
Centrals
Sometimes link loss
happened within 1 hour
Parallel Central and
Peripheral
Two independent
Peripheral and
Central
Sometimes link loss
happened within 1 hour
Case 3
Three BLE links
Central
Three independent
Peripherals
OK
Case 4
Four BLE links
Central
Four independent
Peripherals
OK
Note: Multilink scenario with BM70 as Central for two links and Peripheral for third link is also
supported. Limitations apply.
Added new UART commands in Manual mode
Queued writes are enabled (Queued writes now enabled for characteristics within a service)
Auto pattern data to be transmitted only when End of data is indicated using GPIO.
Note: Auto pattern Test tool does not support this feature. However, when MCU application is
implemented this feature can be used.
Added UART Parity and Stop bit configuration in UI tool.
Note: Parity enabling is not supported in Manual pattern Test tool /Auto Test pattern tool as
these tool access the MCP 2200 UART to USB converter. MCP 2200 supports fixed stop bit and
does not support parity.


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: IS1870

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip IS1870 stil et spørgsmål nedenfor, og andre brugere vil svare dig