Microchip MIC2295YML Manual

Microchip Ikke kategoriseret MIC2295YML

Læs gratis den danske manual til Microchip MIC2295YML (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 3.7 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Microchip MIC2295YML, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
MIC2295 MLF ® Evaluation Board
1.2MHz PWM Step-Up Converter
MLF is a registered trademark of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
February 2009
M9999-020509-B
General Description
The Micrel MIC2295 is a small 1.2MHz constant
frequency PWM DC/DC step-up switching regulator.
The MIC2295 is available in either a thin SOT-23 or a
2mm x 2mm MLF ® package. High power densities, in
a very small size, are achieved using its internal
34V/1.2A switch.
Requirements
The MIC2295 evaluation board requires an input
power source that is able to deliver greater than 1.2A
at 2.5V.
Precautions
The evaluation board does not have reverse polarity
protection. Applying a negative voltage to the VIN
terminal may damage the device.
The MIC2295 evaluation board is tailored for a Li-ion
range input supply voltage. The MIC2295 evaluation
board should not exceed 6.3V on the input unless the
standard input capacitor is replaced with a higher
rated input capacitor.
Getting Started
1. Connect an external supply to V IN. Apply
desired input voltage to the V IN (J1) and
ground (J2 and J5) terminals of the evaluation
board, paying careful attention to polarity and
supply voltage (2.5V≤V IN≤6.3V). An ammeter
may be placed between the input supply and
the VIN terminal to the evaluation board.
Ensure that the supply voltage is monitored at
the VIN terminal. The ammeter and/or power
lead resistance can reduce the voltage
supplied to the input. A 10uF input capacitor is
used on the evaluation board to help
compensate for long cables used in most lab
settings.
2. Connect the load to the V OUT (J4) and
ground terminals. The load can be either
passive (resistor) or active (electronic load).
An ammeter can be placed between the load
and the V OUT terminal. The default output
voltage is set to 12V. This can be adjusted by
changing the feedback resistors.
3. Enabling the MIC2295. Apply a 1.5V or
greater voltage to the enable (J3) terminal.
Ordering Information
Part Number Description
MIC2295YML EV 1.2MHz PWM Step-Up Converter

Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: MIC2295YML

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip MIC2295YML stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Microchip Manualer

Microchip

Microchip M2GL060 Manual

2 December 2025
Microchip

Microchip RTPF500TS Manual

2 December 2025
Microchip

Microchip M1A3P600L Manual

1 December 2025
Microchip

Microchip M2S090TS Manual

1 December 2025
Microchip

Microchip M1A3P1000L Manual

1 December 2025
Microchip

Microchip M2S090 Manual

30 November 2025
Microchip

Microchip A3PE3000L Manual

30 November 2025
Microchip

Microchip HC12-100S0s Manual

30 November 2025
Microchip

Microchip M2GL010T Manual

29 November 2025
Microchip

Microchip M2GL150T Manual

29 November 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vinotemp

Vinotemp BR-RETRO-01-W Manual

17 December 2025
NightStick

NightStick INTRANT XPP-5566RX Manual

17 December 2025
Vaxcel

Vaxcel T0690 Manual

17 December 2025
Silverstone

Silverstone TS12 Manual

17 December 2025
TOTO

TOTO Silas TS210P Manual

17 December 2025
Wine-Mate

Wine-Mate WM-8500DS Manual

17 December 2025
Arçelik

Arçelik A75L 8870 5B Manual

17 December 2025
Dals

Dals RWS48-CC Manual

17 December 2025
Vinotemp

Vinotemp BR-30SSGG Manual

17 December 2025
Gamdias

Gamdias Aura GC1 Elite Manual

17 December 2025