Microchip MIC2298-15YML Manual

Microchip Ikke kategoriseret MIC2298-15YML

Læs gratis den danske manual til Microchip MIC2298-15YML (6 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 36 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 18.5 anmeldelser. Har du et spørgsmål om Microchip MIC2298-15YML, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/6
MIC2298 Evaluation Board
3.5A I
SWMIN
,1MHz, High Power LED
Driver 3 Preset LED Current Setting
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (
408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
June 2008 M9999-062508-B
General Description
This board enables the evaluation of the MIC2298, a fully
integrated 7W net output minimum High Power white LED
driver. The board includes components necessary to set
the LED current to 20%, 50% and 100% of the nominal
LED current (1A). The external inputs also allow the LED
current to be programmed either with additional resistors
or voltages on the DIM or BRT pins. Also the enable pin
can be driven to force the part into low I
Q
mode.
The MIC2298, 1MHz, Integrated Step up current regulator,
allows the use of small and very few external components
to create a compact boosted supply up to 30V. The
evaluation board has been configured with three fixed
current settings chosen using JP1 and all externally
programmable inputs are accessible via board pins.
Requirements
The MIC2298 evaluation board requires an input power
source that is able to deliver at least 5A over the desired
input voltage range. For the load, an electronic load (E-
Load) capable of constant voltage testing is required or a
high power LED mounted on a fan cooled heat sink. Note
that stability measurements must be carried out on an LED
load as E-Loads do not have the same dynamic
characteristics of a high power LED.
Precautions
The evaluation board does not have reverse polarity
protection. Applying a negative voltage to the V
IN
(J1)
terminal may damage the device.
The load current is only regulated if connected between
V
OUT
and FB terminals, the GND terminal close to the V
OUT
terminal is provided for voltage measurements only.
The MIC2298 has a maximum input voltage rating of 10V
therefore, the supply voltage should never exceed this
value.
Getting Started
1. Connect the input supply to the input terminals.
Take note of the polarity to prevent damage. An
ammeter can be used in-line with the VIN terminal
to measure input current. The Input voltage should
be measured at the input terminals to account for
any drops in test leads and amp meter.
2. Ensuring the jumper JP1 is at the top position
(50% load), connect the load to the output
terminals: +VO connects to the positive E-Load
input or Anode of the test LED, FB connects to the
negative E-Load input or the Cathode of the test
LED.
A low impedance ammeter can be connected in-
line with the +VO terminal for current
measurements. The output voltage should be
measured between the evaluation board terminals
+VO and GND (to measure converter efficiency) or
+VO and FB (to measure the voltage of the LED
load).
3. Connect a normally closed (NC) momentary
switch between enable and GND or alternatively,
connect a pulse generator set to output a 2V pulse
of 300ms every 3s to the enable input.
4. Switch on the E-Load (if using), pulse generator
and then the input supply. Measurements can now
be taken of efficiency, switching waveform and
output current regulation. When testing 1A load
(JP1 open), ensure that these are only pulse tests
to prevent damage to the LED. LED manufac-
turers recommend <10% duty cycle and 3s period.
Ordering Information
Part Number Description
MIC2298-15YML EV Evaluation Board with MIC2298-
15YML 15V OVP Device

Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: MIC2298-15YML

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip MIC2298-15YML stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Microchip Manualer

Microchip

Microchip PIC16F87 Manual

25 Oktober 2025
Microchip

Microchip PIC18F2620 Manual

25 Oktober 2025
Microchip

Microchip RN240 Manual

24 Oktober 2025
Microchip

Microchip PIC24HJ12GP201 Manual

24 Oktober 2025
Microchip

Microchip TC4420 Manual

24 Oktober 2025
Microchip

Microchip HV2818 Manual

23 Oktober 2025
Microchip

Microchip MIC2298 Manual

23 Oktober 2025
Microchip

Microchip PIC16F630 Manual

23 Oktober 2025
Microchip

Microchip PIC32MZ2048EFG144 Manual

21 Oktober 2025
Microchip

Microchip PIC18F46J50 Manual

21 Oktober 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

IFM

IFM EBC066 Manual

1 November 2025
Dahua Technology

Dahua Technology HAC-ME1200E Manual

1 November 2025
Wimberley

Wimberley AP-554 Manual

1 November 2025
Eliminator Lighting

Eliminator Lighting E 108 Manual

1 November 2025
IFM

IFM EBC001 Manual

1 November 2025
Bluestork

Bluestork KB-MAC Manual

1 November 2025
IFM

IFM EBC021 Manual

1 November 2025
Yamazen

Yamazen EKS-V3 Manual

1 November 2025
Olimpia Splendid

Olimpia Splendid Bi2 SL SMART S1 Manual

1 November 2025
Russell Hobbs

Russell Hobbs Colours Plus 20417-70 Manual

1 November 2025