Microchip MIC26603 Manual

Microchip Ikke kategoriseret MIC26603

Læs gratis den danske manual til Microchip MIC26603 (9 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.0 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Microchip MIC26603, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/9

MIC26603 Evaluation Board

28V, 6A HyperLight Load®

Synchronous DC-DC Buck Regulator

SuperSwitcher IIG™

Hyper Light Load and Hyper Speed Control are trademarks of Micrel, Inc.

MLF and Lead Frame are registered trademarks of Amkor Technology, Inc.Micro

Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 ( 408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com

July 2011 M9999-071511-A

lat

t current. The output voltage is a

rov

TON ripp

er-sag condi

rt feature is provided to reduce th

tio of the IC

et and supporting documentation

General Description

The MIC26603 DC-DC regulator operates ov

supply range of 4.5V to 28V and provides a regu

at up to 6A of outpu

an input

ed output

djustable

e device

switching

to 0.8V with a typical accuracy of ±1%, and

operates at a switching frequency of 600kHz. T

frequency remains fairly constant with chang

voltage and output load.

Micrel’s Hyper Light L

s in input

ides the

onse as

edium to

der light

equency,

oad™ architecture p

same high-efficiency and ultra-fast transient re

the Hyper Speed Control™ architecture under

heavy loads, but also maintains high efficiency

load conditions by transitioning to variable

discontinuous mode operation.

The MIC26603 utilizes an adaptive le control

ovided to

tions. An

e inrush

ort-circuit

architecture. An undervoltage lockout feature is p

ensure proper operation under pow

internal soft-sta

current. Foldback current limit and “hiccup” mode

protection and thermal shutdown ensures protec

during fault conditions.

Note: This evaluation board is for 6A applicatio

The datashe can be

found on Micrel’s web site at: www.micrel.com.

Requirements

The MIC26603 provides a 5V regulated outp

voltage VIN ranging from 5.5V to 28V. When

ut for input

VIN < 5.5V,

VDD should be tied to PVIN pins to bypass the internal

linear regulator by a jumper. The output load can either be

an active or passive load.

Precautions

The evaluation board does not have reverse polarity

protection. Applying a negative voltage to the VIN terminal

may damage the device. In addition, the maximum VIN

operating voltage of the MIC26603 evaluation board is

28V. Exceeding 29V on VIN could damage the device

capacitance and also makes (High VIN)/(Low VOUT).

ly to the VIN terminal.

e to the VIN and ground

board, paying careful

ly voltage. An ammeter

d ut supply and the VIN

oard. Ensure that the

at the VIN terminal. The

resistance can reduce

put.

e VOUT and ground

ither passive (resistive)

load). An ammeter can

and the V OUT terminal.

s monitored at the

set to 0.9V, 1.0V, 1.2V,

5.0V by a jumper. If a

it can be adjusted by

ck resistors. See “Output

” section.

th 03. The EN pin is provided on

th e MIC26603

tu DD the UVLO threshold.

The output of the MIC26603 may be turned off by

shorting the EN pin to ground. A connection on the

board provides easy access to the enable pin.

Ordering Information

Part Number Description

Getting Started

1. Connect an external supp

Apply the desired input voltag

terminals of the evaluation

attention to polarity and supp

may be place between the inp

terminal to the evaluation b

supply voltage is monitored

ammeter and/or power lead

the voltage supplied to the in

2. Connect the load to th

terminals. The load can be e

or active (as in an electronic

be placed between the load

Ensure that the output voltage i

VOUT terminal. VOUT can be

1.5V, 1.8V, 2.5V, 3.3V, or

different voltage is needed,

changing the feedba

Voltage

3. Enable e MIC266

ation boarde evalu . The output of th

rns on when V exceeds

MIC26603YJL EV 6A HLL DC-DC Regulator Evaluation

Board

Produkt Specifikationer

Mærke:	Microchip
Kategori:	Ikke kategoriseret
Model:	MIC26603

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip MIC26603 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Microchip Manualer

Microchip M2GL060 Manual

2 December 2025

Microchip RTPF500TS Manual

2 December 2025

Microchip M1A3P600L Manual

1 December 2025

Microchip M2S090TS Manual

1 December 2025

Microchip M1A3P1000L Manual

1 December 2025

Microchip M2S090 Manual

30 November 2025

Microchip A3PE3000L Manual

30 November 2025

Microchip HC12-100S0s Manual

30 November 2025

Microchip M2GL010T Manual

29 November 2025

Microchip M2GL150T Manual

29 November 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vinotemp BR-RETRO-01-W Manual

17 December 2025

NightStick INTRANT XPP-5566RX Manual

17 December 2025

Vaxcel T0690 Manual

17 December 2025

Silverstone TS12 Manual

17 December 2025

TOTO Silas TS210P Manual

17 December 2025

Wine-Mate WM-8500DS Manual

17 December 2025

Arçelik A75L 8870 5B Manual

17 December 2025

Dals RWS48-CC Manual

17 December 2025

Vinotemp BR-30SSGG Manual

17 December 2025

Gamdias Aura GC1 Elite Manual

17 December 2025