Microchip MIC45116-1YMP Manual

Microchip Ikke kategoriseret MIC45116-1YMP

Læs gratis den danske manual til Microchip MIC45116-1YMP (8 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 17 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 9 anmeldelser. Har du et spørgsmål om Microchip MIC45116-1YMP, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/8
MIC45116 Evaluation Board
20V/6A/DC- - to DC Power Module
General Description
Micrel’s MIC45116 is a synchronous step down regulator -
module, featuring a unique adaptive ON time control -
architecture. The singular module package cludes in -a DC
to-DC controller, power MOSFETs, bootstrap diode,
bootstrap capacitor, and an inductor; simplifying the design
and layout process for the end user.
This highly integrated solution expedites system design
and improves product time- -to market. The internal
MOSFETs and inductor have been optimized to achieve
high efficiency at a low output voltage. The fully optimized
design can deliver up to a 6A current under a wide input
voltage range of 4.75V to 20V, without an additional
cooling requirement.
The MIC 1 uses Micrel’s HyperLight Load45116- ® . (HLL)
MIC45116-2 uses Micrel’s Hyper Speed Control™
architecture which enables ultra fast load transient -
response s and allow for a reduction of output capacitance.
The MIC45116 offers 1% output accuracy that can be
adjusted from 0.8V input voltage with two up ofto 85% the
external resistors. Note the output capacitor Cb is only
rated to 6.3V.
The basic parameters of th evaluation board include a is
4.75V to 20V input, a 0.8V to 5V at 6A output.
Datasheets and support documentation are available on
Micrel’s web site at: www.micrel.com.
Requirements
The MIC45116 1 and MIC45116 2 evaluation board’s - -
minimum requirement is one power supply with at least 6A
current capability. No external linear regulator is required
to power the internal biasing of the IC because the
MIC45116 has an internal PVDD LDO. In the applications
with VIN < +5.5V, PVDD should be tied to VIN to bypass
the internal linear regulator. The output load can either be
a passive or an active load.
Precautions
The MIC45116 evaluation board does not have reverse
polarity protection. Applying a negative voltage to the VIN
and GND terminals may damage the device. The
maximum VIN of the board is rated at 20V. Exceeding 30V
on the VIN could damage the device. The voltage rating of
the output capacitor is 6.3V. The output capacitor should
be replaced with higher voltage rated one to set the output
voltage above 5V.
Getting Started
1. VIN Supply
Connect a supply to the VIN (TP6) (TP7) and GND
terminals, paying careful attention to the polarity and
the supply range (4.75V < VIN < 20V). Monitor IIN with
a current meter and monitor input voltage at VIN and
GND terminals with a voltmeter. Do not apply power
until Step 4.
2. Connect Load and Monitor Output
Connect a load to the VOUT (TP8) (TP9) and GND
terminals. The load can be either a passive (resistive)
or an active (as in an electronic load) type. A current
meter may be placed between the VOUT terminal and
load to monitor the output current. Ensure the output
voltage is monitored at the VOUT terminal.
3. Enable Input
The EN pin has an on board 100kΩ pull-up resistor
(R4) to VIN, which allows the output to be turned on
when PVDD exceeds its UVLO threshold. An EN
connector (TP3) is provided on the evaluation board
for users to easily access the enable feature. Applying
an external logic signal on the EN pin to pull it low or
using a jumper to short the EN pin to GND will shut off
the output of the MIC45116 evaluation board.
4. Turn Power
Turn on the VIN supply and verify that the output
voltage is regulated to 1.8V.
5. Loop Measurement
Control loop frequency response can be measured by
injecting AC sweep signal and measuring voltage
across test points A and B. R3 should change to a
small resistor value in the range of 10 to 20Ω Ω for the
loop measurement.
Ordering Information
Part Number Description
MIC45116 MIC45116- 1YMP EV -1 Evaluation Board
MIC45116 MIC45116- 2YMP EV -2 Evaluation Board
Hyper LightLoad is a registered trademark of Micrel, Inc.
Hyper Speed Control is a trademark of Micrel, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
March 12 , 2015 Revision 1.0

Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: MIC45116-1YMP

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip MIC45116-1YMP stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Microchip Manualer

Microchip

Microchip M2GL060 Manual

2 December 2025
Microchip

Microchip RTPF500TS Manual

2 December 2025
Microchip

Microchip M1A3P600L Manual

1 December 2025
Microchip

Microchip M2S090TS Manual

1 December 2025
Microchip

Microchip M1A3P1000L Manual

1 December 2025
Microchip

Microchip M2S090 Manual

30 November 2025
Microchip

Microchip A3PE3000L Manual

30 November 2025
Microchip

Microchip HC12-100S0s Manual

30 November 2025
Microchip

Microchip M2GL010T Manual

29 November 2025
Microchip

Microchip M2GL150T Manual

29 November 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vinotemp

Vinotemp BR-RETRO-01-W Manual

17 December 2025
NightStick

NightStick INTRANT XPP-5566RX Manual

17 December 2025
Vaxcel

Vaxcel T0690 Manual

17 December 2025
Silverstone

Silverstone TS12 Manual

17 December 2025
TOTO

TOTO Silas TS210P Manual

17 December 2025
Wine-Mate

Wine-Mate WM-8500DS Manual

17 December 2025
Arçelik

Arçelik A75L 8870 5B Manual

17 December 2025
Dals

Dals RWS48-CC Manual

17 December 2025
Vinotemp

Vinotemp BR-30SSGG Manual

17 December 2025
Gamdias

Gamdias Aura GC1 Elite Manual

17 December 2025