Microchip MIC5373 Manual


Læs gratis den danske manual til Microchip MIC5373 (22 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 35 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 18 anmeldelser. Har du et spørgsmål om Microchip MIC5373, eller vil du spørge andre brugere om produktet?

Side 1/22
MIC5373/83
Triple 200mA µCap
LDO in 2.5mm x 2.5mm Thin MLF®
MLF and MicroLeadFrame are registered trademarks of Amkor Technology, Inc.
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
General Description
The MIC5373/83 is a triple output device with three 200mA
LDOs which is ideal for application processor support in
mobile platforms. The MIC5373 provides independent
control active high enables for each of the 200mA LDOs.
The MIC5383 provides active low enables. Both the
MIC5373 and MIC5383 are available in the tiny 2.5mm x
2.5mm Thin MLF® package.
The MIC5373/83 is designed for high input ripple rejection
(high PSRR) and provides low output noise making it ideal
for powering sensitive RF circuitry such as GPS, WiFi and
Bluetooth applications. The MIC5373/83 also incorporates
a power-on-reset (POR) supervisor with adjustable delay
time set by an external capacitor, and an independent
input pin to monitor any voltage level. Once high, the POR
output can be asserted low again by enabling the manual
reset (MR) pin. When the MR pin is restored low, the POR
output will re-time the delay set by the external delay
capacitor.
The MIC5373/83 operates with very small ceramic output
capacitors to reduce board space and component cost. It
is available in various fixed output voltages. The
MIC5373/83 has a junction temperature range from 40°C
to 125°C.
Datasheets and support documentation can be found on
Micrel’s web site at: www.micrel.com.
Features
1.7V to 5.5V input supply voltage range
Output current - 200mA LDO1/2/3
High output accuracy (±2%)
Independent enable pins
POR with user-defined voltage monitoring
POR voltage input
Adjustable delay time
Manual reset pin
Low dropout voltage – 170mV at 150mA
High PSRR - 55dB at 1kHz on each LDO
Stable with tiny ceramic output capacitors
2.5mm x 2.5mm Thin MLF16-pin package
Thermal-shutdown and current-limit protection
Applications
Mobile phones
GPS receivers
Application co-processors
PDAs and handheld devices
Typical Application
Typical MIC5373-xxxYMT Circuit
(Active High Enable)
Typical MIC5383-xxxYMT Circuit
(Active Low Enable)
September 2012 M9999-091712
Micrel, Inc. MIC5373/83
September 2012 2 M9999-091712
Ordering Information
Part Number Mark
Code
Output
Voltage(1)
Junction
Temperature Range Package Lead Finish
MIC5373-MG4YMT MG4 2.8V/1.8V/1.2V –40° to +125°C 16-Pin 2.5mm x 2.5mm Thin MLF Pb-free
MIC5373-SJGYMT SJG 3.3V/2.5V/1.8V –40° to +125°C 16-Pin 2.5mm x 2.5mm Thin MLF Pb-free
MIC5383-MG4YMT Z1T 2.8V/1.8V/1.2V 40° to +125°C 16-Pin 2.5mm x 2.5mm Thin MLF Pb-free
MIC5383-SJGYMT Z5T 3.3V/2.5V/1.8V 40° to +125°C 16-Pin 2.5mm x 2.5mm Thin MLF Pb-free
Note:
1. Other voltage options available. Contact Micrel for details.
2. Lead finish is NiPdAu. Mold compound material is halogen free.
Pin Configuration
MIC5373
16-Pin 2.5mm x 2.5mm Thin MLF (MT)
(Top View)
MIC5383
16-Pin 2.5mm x 2.5mm Thin MLF (MT)
(Top View)


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: MIC5373

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip MIC5373 stil et spørgsmål nedenfor, og andre brugere vil svare dig