Microchip NX7101 Manual

Microchip Ikke kategoriseret NX7101

Læs gratis den danske manual til Microchip NX7101 (23 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Microchip NX7101, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/23

- 6 Voltage-Mode, Current-Mode (and Hysteretic Control) TN 20

by Sanjaya Maniktala

Rev 0.5 - -12 Analog Mixed Signal Group / 07 30

1 Enterprise, Aliso Viejo, CA 92656, USA; Within the USA: (800) 713-4113, Outside the USA: (949) 221-7100 Fax: (949) 756- 0308

Introduction

Switching regulators have been with us for many years. They were considered tricky to design –

and still are. In 1976 Silicon General (later LinFinity, then Microsemi), introduced the irst

monolithic (IC-based) switching controller, the SG1524 “Pulse Width Integrated Circuit”. A little

later, this chip was improved and became the “SG3524” historic industry workhorse. And very soon

thereafter, it was available from multiple chip vendors. Keep in mind that switching stages based on

discrete designs were already gaining ground, particularly in military applications. In fact, some

resourceful engineers had even made “switch mode power supplies” by adding related circuitry -

around one of the highest-selling chips in history: the “555 timer” (sometimes called the “IC Time

Machine”), introduced in 1971 by Signetics (later Philips, then NXP). The SG1524 was however the

irst all IC in which the required control functionality was present on a single chip/die. With the

rapidly escalating concurrent interest in switching power supplies at the time, it is no surprise that

as early as 1977 the very irst book on the subject, written by the late Abraham Pressman, appeared

on the scene. Together, these events spurred interest in an area well beyond most people’s

expectations, and ushered in the world of switching power conversion as we know it today.

The SG1524/3524 drove a pair of (bipolar) switching transistors with a “duty cycle” (ratio of switch

ON-time to the total time period) which was proportional to the “control voltage”. By using switching

transistors to switch the input voltage source ON and OFF into an LC low pass ilter, a relatively

eficient voltage regulator was produced. At the heart of this regulator was the “PWM (pulse width

modulator) comparator”. The output pulse-train to drive the transistors with was a result of

applying a (relatively) smooth control voltage on one of this comparator’s input terminals, along

with a “sawtooth” or “PWM ramp” a generated from the clock Figure 1, on its other input. See . This

technique is known as "voltage-mode programming”, or “voltage mode control” (“VMC”) –- since the

duty cycle is proportional to the control voltage. The control voltage is in effect the difference

between the actual output voltage and the “reference” value (the value we want to fix the output at,

i.e. the “setpoint”). We will discuss this igure in more detail shortly.

Another well-known technique today, which has also been around since the 80s, senses the peak

current in the power switch or inductor, and turns the switch OFF at a programmed level of

current. This technique is called current-mode control (“CMC”). Keep in mind it was not brand-“

new at the time. In fact it had been discovered years ago, but few had realized its signiicance till ”

Unitrode Corp. (now Texas Instruments) came along. It received a huge boost in popularity in the

form of the world’s first current-mode control (CMC) chip, the Flyback controller UC1842 from

Unitrode In CMC, there is in effect a (fast-. acting) “inner” current loop along with the “outer”

(slower) “voltage loop” which carries out the output regulation. See the note on ramp generation

within , indicating how this particular aspect is different between VMC and CMC. Prima Figure 1

Produkt Specifikationer

Mærke:	Microchip
Kategori:	Ikke kategoriseret
Model:	NX7101

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip NX7101 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Microchip Manualer

Microchip M2GL060 Manual

2 December 2025

Microchip RTPF500TS Manual

2 December 2025

Microchip M1A3P600L Manual

1 December 2025

Microchip M2S090TS Manual

1 December 2025

Microchip M1A3P1000L Manual

1 December 2025

Microchip M2S090 Manual

30 November 2025

Microchip A3PE3000L Manual

30 November 2025

Microchip HC12-100S0s Manual

30 November 2025

Microchip M2GL010T Manual

29 November 2025

Microchip M2GL150T Manual

29 November 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vinotemp BR-RETRO-01-W Manual

17 December 2025

NightStick INTRANT XPP-5566RX Manual

17 December 2025

Vaxcel T0690 Manual

17 December 2025

Silverstone TS12 Manual

17 December 2025

TOTO Silas TS210P Manual

17 December 2025

Wine-Mate WM-8500DS Manual

17 December 2025

Arçelik A75L 8870 5B Manual

17 December 2025

Dals RWS48-CC Manual

17 December 2025

Vinotemp BR-30SSGG Manual

17 December 2025

Gamdias Aura GC1 Elite Manual

17 December 2025