Microchip PIC24HJ128GP510 Manual

Microchip Ikke kategoriseret PIC24HJ128GP510

Læs gratis den danske manual til Microchip PIC24HJ128GP510 (84 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 10 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 5.5 anmeldelser. Har du et spørgsmål om Microchip PIC24HJ128GP510, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/84

dsPIC33F/PIC24H

1.0 DEVICE OVERVIEW

This document defines the programming specification

for the dsPIC33F 16-bit Digital Signal Controller (DSC)

and PIC24H 16-bit Microcontroller (MCU) families. This

programming specification is required only for those

developing programming support for the dsPIC33F/

PIC24H family. Customers using only one of these

devices should use development tools that already

provide support for device programming.

Topics covered include:

1.0 Device Overview ......................................................... 1

2.0 Programming Overview of the dsPIC33F/PIC24H ...... 1

3.0 Device Programming – Enhanced ICSP ..................... 8

4.0 The Programming Executive ..................................... 19

5.0 Device Programming – ICSP .................................... 28

6.0 Programming the Programming Executive

to Memory ................................................................. 45

7.0 Device ID................................................................... 50

8.0 AC/DC Characteristics and Timing Requirements .... 54

Appendix A: Hex File Format .............................................. 57

Appendix B: Device ID Register Silicon Errata Addendum . 58

Appendix C: Diagnostic and Calibration Registers ............. 59

Appendix D: Checksum Computation ................................. 61

Appendix E: Revision History.............................................. 74

2.0 PROGRAMMING OVERVIEW

OF THE dsPIC33F/PIC24H

There are two methods of programming the dsPIC33F/

PIC24H family of devices discussed in this

programming specification. They are:

• In-Circuit Serial Programming™ (ICSP™)

programming capability

• Enhanced In-Circuit Serial Programming

The ICSP programming method is the most direct

method to program the device; however, it is also the

slower of the two methods. It provides native, low-level

programming capability to erase, program and verify

the chip.

The Enhanced ICSP protocol uses a faster method that

takes advantage of the programming executive, as

illustrated in . The programming executiveFigure 2-1

provides all the necessary functionality to erase,

program and verify the chip through a small command

set. The command set allows the programmer to

program the dsPIC33F/PIC24H Programming

Specification devices without having to deal with the

low-level programming protocols of the chip.

FIGURE 2-1: PROGRAMMING SYSTEM

OVERVIEW FOR

ENHANCED ICSP™

This specification is divided into major sections that

describe the programming methods independently.

Section 3.0 “Device Programming – Enhanced

ICSP” describes the Enhanced ICSP method.

Section 5.0 “Device Programming – ICSP”

describes the ICSP method.

2.1 Power Requirements

All devices in the dsPIC33F/PIC24H family are dual

voltage supply designs: one supply for the core and

another for the peripherals and I/O pins. A regulator is

provided on-chip to alleviate the need for two external

voltage supplies.

All of the dsPIC33F/PIC24H devices power their core

digital logic at a nominal 2.5V. To simplify system

design, all devices in the dsPIC33F/PIC24H

Programming Specification family incorporate an

on-chip regulator that allows the device to run its core

logic from VDD.

The regulator provides power to the core from the other

VDD pins. A low-ESR capacitor (such as tantalum) must

be connected to the VCAP pin (Figure 2-2). This helps

to maintain the stability of the regulator. The

specifications for core voltage and capacitance are

listed in Section 8.0 “AC/DC Characteristics and

Timing Requirements”.

dsPIC33F/PIC24H

Programmer Programming

Executive

On-Chip Memory

dsPIC33F/PIC24H Flash Programming Specification

dsPIC33F/PIC24H PROGRAMMING SPECIFICATION

FIGURE 2-2: CONNECTIONS FOR THE

ON-CHIP REGULATOR

2.2 Program Memory Write/Erase

Requirements

The program Flash memory on the dsPIC33F/PIC24H

has a specific write/erase requirement that must be

adhered to, for proper device operation. The rule is that

any given word in memory must not be written without

first erasing the page in which it is located. Thus, the

easiest way to conform to this rule is to write all the data

in a programming block within one write cycle. The

programming methods specified in this document

comply with this requirement.

2.3 Pins Used During Programming

The pins that are used for programming are listed in

Table 2-1.

TABLE 2-1: PINS USED DURING PROGRAMMING

Note 1: These are typical operating voltages. Refer

to TABLE 8-1: “AC/DC Characteristics

and Timing Requirements” for the full

operating ranges of VDD and VCAP.

2: It is important for the low-ESR capacitor to

be placed as close as possible to the V

CAP

pin.

VDD

VCAP

VSS

dsPIC33F/PIC24H

CEFC

3.3V

Note: A program memory word can be

programmed twice before an erase, but

only if (a) the same data is used in both

program operations or (b) bits containing

‘1’ are set to ‘0’ but no ‘0’ is set to ‘1’.

Note: Refer to the specific device data sheet for

complete pin diagrams of the dsPIC33F/

PIC24H devices.

Pin Name

During Programming

Pin Name Pin Type Pin Description

MCLR MCLR P Programming Enable

VDD and AVDD(1) VDD P Power Supply

VSS and AVSS(1) VSS P Ground

VCAP CAPV P CPU Logic Filter Capacitor Connection

PGEC1 PGEC1 I Primary Programming Pin Pair: Serial Clock

PGED1 PGED1 I/O Primary Programming Pin Pair: Serial Data

PGEC2 PGEC2 I Secondary Programming Pin Pair: Serial Clock

PGED2 PGED2 I/O Secondary Programming Pin Pair: Serial Data

PGEC3 PGEC3 I Tertiary Programming Pin Pair: Serial Clock

PGED3 PGED3 I/O Tertiary Programming Pin Pair: Serial Data

Legend: I = Input O = Output P = Power

Note 1: All power supply and ground pins must be connected, including analog supplies (AVDD) and ground

(AV ).SS

Produkt Specifikationer

Mærke:	Microchip
Kategori:	Ikke kategoriseret
Model:	PIC24HJ128GP510

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip PIC24HJ128GP510 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Microchip Manualer

Microchip HS12-100D0/12DS2F Manual

18 Februar 2025

Microchip HSA0-040SDA/A0SA10 Manual

18 Februar 2025

Microchip HSA0-040SIA/A0S1F Manual

18 Februar 2025

Microchip HT12-100S0s/12ST25 Manual

17 Februar 2025

Microchip EMC2103-2 Manual

17 Februar 2025

Microchip EMC1047 Manual

17 Februar 2025

Microchip HCS201 Manual

17 Februar 2025

Microchip LE9653 Manual

17 Februar 2025

Microchip LAN7430 Manual

17 Februar 2025

Microchip HCS500 Manual

17 Februar 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Planet XGPN-100 Manual

15 Juni 2025

Proficook PC-EKA 1283 Manual

15 Juni 2025

OmniMount OBSP8 Manual

15 Juni 2025

Levenhuk FS10 Manual

15 Juni 2025

Vestil PM4-2148-LP Manual

15 Juni 2025

ElectriQ STRV-W1-B Manual

15 Juni 2025

Adler AD 4521 Manual

15 Juni 2025

AMX HydraPort HPX-AV102 Manual

15 Juni 2025

Hughes & Kettner Red Box Mk II Manual

15 Juni 2025

Hughes & Kettner Quantum QC 412 Manual

15 Juni 2025