Microchip SR10DB1 Manual

Microchip Ikke kategoriseret SR10DB1

Læs gratis den danske manual til Microchip SR10DB1 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Microchip SR10DB1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

Supertex inc.

www.supertex.com

SR10DB1

Doc.# DSDB-SR10DB1

A040113

- DC Output +

24V

12V

ADJ

HIGH EVOLTAG

Supertex SR10DB1

COUT

AC Input

90-275VRMS

50/60Hz

–

Load

FB1

and R

FB2

optional for output voltages other

than 6, 12, or 24V. Adjustment range is 6 - 28V.

Pre-configured for 9V. Pads for 0603 and 0805.

DC Output:

6, 12, 24V or

adjustable 6 - 28V.

Jumper-selectable full-wave

or half-wave rectification.

Both jumpers must be in the

same position, left or right.

Jumper-selectable output voltage.

Jumper must be present. When in

the ADJ position, RFB1 and RFB2

must be present.

Output minus is

connected to AC line

neutral when configured

for half-wave rectification.

RFB1

RFB2

RBL

RLIM

DOUT

One lead must always

be in this position

Socketed components.

Accomodates various capacitor sizes

IC1

H Input N AC

Rect

Half

Full

VOUT

Board Layout and Connection Diagram

Inductorless Switching

Power Supply Demoboard

Specications

Parameter Value

AC Input 90VAC to 275VAC

50Hz to 60Hz

Output voltage 6V, 12V, 24V ±10%

or 6-28V using divider

Output current1up to 50mA

No-load input power 1as low as 20mW

Efciency1up to 75%

Actual board size 88mm x 28mm

Introduction:

The Supertex SR10 is an inductorless switching power sup-

ply controller intended for operation directly from a rectied

120/240VAC line. Due to the capacitor-coupled, switched

shunt topology (CCSS), it exhibits low standby power and

good efciency while employing no magnetics nor high volt-

age electrolytic capacitors.

To meet a wide variety of applications, the SR10DB1 is

highly congurable. Many components are socketed. Half or

full-wave rectication is jumper-selectable. Output voltage is

jumper-selectable to 3 xed voltages or may be set anywhere

in the range of 6 - 28V using an on-board feedback divider.

AC Input (H and N)

Connect to the AC line. The ‘H’ terminal should be connected

to the AC line hot conductor. The ‘N’ terminal should be con-

nected to the AC line neutral conductor. When congured for

half-wave rectication, the N terminal is connected to the DC

output minus (–) terminal.

DC Output (+ and –)

Connect the load to these terminals. Do not connect earth-

grounded loads or test equipment without using an isolation

transformer on the AC line.

Output voltage is jumper-selectable at 6, 12, or 24V, or it

may be set in the range of 6 - 28V using the R FB feedback

divider and setting the jumper to ADJ.

Notes:

1. Dependent upon conguration and degree of transient protection.

SR10DB1

Supertex inc.

www.supertex.com

Doc.# DSDB-SR10DB1

A040113

Schematic

D1-4

1N4001

RLIM

RBL

fixed 6, 12, 24, or 9V

(adjustable from 6 - 28V via RFB1)

OUT

COUT

1.0mF

RFB1

422kΩ

DOUT

1N4001

VIN

90-275VAC

50-60Hz

RTN

OUT

SR10

PGND

AGND

D12

D24

CFB

470pF

24V

12V

ADJ

OUT

RFB2

68.1kΩ

Rect

Half Full

D3D4

1 8

Designation Description Value Rating Mfg PN

RLIM Resistor, fusible 2W —22Ω any

RBL Resistor 1/4W —4.7MΩ any

RFB1 Resistor 1/4W —422kΩ any

RFB2 Resistor 1/4W —68.1kΩ any

CSCapacitor, lm 220nF to 2.2µF 275VAC,X2 —any

COUT Capacitor, alum 220µF min —35V any

CFB Capacitor, ceramic NPO 470pF 6V —any

D1 - 4 Rectier any— 1A, 50V 1N4001

DOUT Rectier any— 1A, 50V 1N4001

IC1CCSS regulator — — Supertex SR10

Bill of Materials

Socketed Components

The SR10DB1 is provided with all components pre-installed.

Other components may be substituted for the on-board com-

ponents to meet other requirements.

Refer to the above schematic and BOM, and the drawing

and photo on page 1 to determine the proper locations for

the components.

Output Voltage

Fixed output voltages of 6V, 12V, or 24V may be selected by

setting the appropriate jumper on the VOUT header.

For other output voltages, the on-board resistive feedback

divider may be used to provide any voltage in the range of

6 - 28V. To maintain a minimum 15µA through the feedback

divider, only RFB1 should be changed.

RFB1 = RFB2

VOUT -1 = 68.1kΩ

VOUT -1

VFB

1.25V

Output Current (CS selection)

Output current is primarily dependent on input voltage, CS

value, and rectication (full or half). Given the minimum input

voltage and choice of rectication, the minimum value of CS

Produkt Specifikationer

Mærke:	Microchip
Kategori:	Ikke kategoriseret
Model:	SR10DB1

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip SR10DB1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Microchip Manualer

Microchip AT7913 Manual

1 September 2025

Microchip ATmega1281 Manual

19 Juli 2025

Microchip ATtiny461 Manual

19 Juli 2025

Microchip ATxmega128D3 Manual

19 Juli 2025

Microchip ATxmega128D4 Manual

19 Juli 2025

Microchip ATTINY28 Manual

19 Juli 2025

Microchip ATTINY861 Manual

19 Juli 2025

Microchip ATmega1280 Manual

19 Juli 2025

Microchip ATtiny84A Manual

19 Juli 2025

Microchip ATmega645P Manual

19 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektrobock PT44 Manual

14 September 2025

BSS Audio FDS-366T Manual

14 September 2025

Systemair Airline R-114 Manual

14 September 2025

IFM SU2031 Manual

14 September 2025

Morel Tempo Ultra Integra 502 Manual

14 September 2025

IMC Networks 232CL9R Manual

14 September 2025

Varta Speed Charger 57955 Manual

14 September 2025

Melissa & Doug 9336 Manual

14 September 2025

Opus dataPREDATOR Manual

13 September 2025

Varta Wireless Power Bank 20000 57909 Manual

13 September 2025