Microchip SY88773V Manual

Microchip Ikke kategoriseret SY88773V

Læs gratis den danske manual til Microchip SY88773V (7 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 15 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 8 anmeldelser. Har du et spørgsmål om Microchip SY88773V, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/7
1
M9999-051304
hbwhelp@micrel.com or (408) 955-1690
DESCRIPTION
Rev.: A Amendment: /0
Issue Date: May 2004
FEATURES
The SY88773V features:
■Multirate up to 3.2Gbps operation
■Wide gain-bandwidth product
■Low-noise 50 Ω CML data outputs
■Chatter-free Loss-of-Signal (LOS) output
■Programmable LOS sensitivity
■On-chip input bias for AC-coupled applications
■TTL /EN input
■Wide power supply and temperature operating
range
The SY88773V evaluation board features:
■AC-coupled I/O with SMA connectors
■Single potentiometer to set LOS LVL
■SMA or test points available to measure non-
critical nodes
AVAILABLE MEASUREMENTS
The SY88773V evaluation board allows the following
measurements:
■Frequency performance
■Output eye pattern generation
■Mask testing
■Jitter
■Output rise/fall time
■BER testing
■Hysteresis measurement
EVALUATION BOARD
The SY88773V low-power limiting post amplifier is designed
for use in fiber-optic receivers. The device connects to typical
transimpedance ampliers (TIAs). The linear signal output
from TIAs can contain significant amounts of noise and may
vary in amplitude over time. The SY88773V quantizes these
signals and outputs typically 800mVppvoltage-limited
waveforms.
The SY88773V operates from a single +3.3V 10% or±
+5V ±10% power supply, over an industrial temperature
range of –40 C to +85 C. With its wide bandwidth and high° °
gain, signals with data rates up to 3.2Gbps and as small as
10mVp-p can be amplified to drive devices with CML or PECL
inputs.
The SY88773V incorporates a loss-of-signal (LOS) open-
collector TTL output with internal 5k pull-up resistor. AΩ
programmable loss-of-signal level set pin (LOSLVL) sets the
sensitivity of the input amplitude detection. LOS asserts
high if the input amplitude falls below the threshold set by
LOSLVL and deasserts low otherwise. LOS can be fed back
to the enable (/EN) input to maintain output stability under a
loss of signal condition. /EN deasserts the true output signal
without removing the input signal. Typically, 4.6dB LOS
hysteresis is provided to prevent chattering.
This manual provides information on the SY88773V
evaluation board. It should be used in conjunction with the
SY88773V data sheet, which contains full specications of
the SY88773V.
The SY88773V evaluation board enables fast and thorough
evaluation of the SY88773V 3.2Gbps CML low-power limiting
post amplier. The board is an easy-to-use, 4-layer high-
speed coplanar design. It is designed to be driven by a high-
speed 3.2Gbps pattern generator.
The SY88773V evaluation board is intended to be
terminated to a 50 scope and provides for simple userΩ
adjustability of the LOS threshold through the adjustment of
an on-board potentiometer. This allows the user to evaluate
various parameters of the SY88773V, as listed in the
“Available Measurements” section of this document.
Figure 1. SY88773V Evaluation Board
3.3V/5V 3.2Gbps CML
LOW-POWER LIMITING POST
AMPLIFIER w/ TTL LOS
SY88773V
EVALUATION BOARD
Layer Definition
1 Signal/GND
2 GND
3 VCC
4 GND
Table 1. SY88773V Evaluation Board Layer Stack-Up
2
SY88773V
EVALUATION BOARD
Micrel
M9999-051304
hbwhelp@micrel.com or (408) 955-1690
MEASUREMENT SETUP
Agilent
E3620A
Power
Supply
+
-
+
-
Agilent
83752A
Synthesized
Sweeper
RFOut
Agilent
70843B
Error
Performance
Analyzer
Clock
Input
Data
Out
/Data
Out
Trigger
Out
+–
Tektronix
DMM157
Multimeter
Agilent
70004A
Display
Trigger
In
CH1
Agilent
86100A
Wide-Bandwidth
Oscilloscope
CH2
DIN DOUT
/DOUT/DIN
GND
LOSLVL
VCCVCC
GND
6
7
8
VREF
LOS
VCC
GND
GND
VCC
/EN
2
3
49
10
11
12
16
15
14
13
1
5
SY88773V
TP2
V
CC
TP3
C3
0.1 Fµ
C4
1 Fµ
C5
0.1 Fµ
C6
1 Fµ
C2
0.1 Fµ
C1
0.1 Fµ
S1
S2
C13
0.1 Fµ
C14
1 Fµ
C11
0.1 Fµ
C12
1 Fµ
C15
0.1 Fµ
C10
0.1 Fµ
C9
0.1 Fµ
S5
S4
C7
0.1 Fµ
C8
1 Fµ
S3
S6
VAR1
250kΩ
BP1
BP2
TP1
C40
0.1 Fµ
C41
10 Fµ
U1
R1
49.9Ω
R2
49.9Ω
V
REF
R
FDBK
(optional)
V
CC
V
REF
V
CC
V
CC
V
CC
Figure 2. Setup for Measurements
Equipment used for measurements:
1. Agilent 83752A Synthesized Sweeper
2. Agilent 70004A Display
3. Agilent 70843B Error Performance Analyzer
4. Agilent 86100A Wide-Bandwidth Oscilloscope
5. Two (2) MCL BW S15W2 40dB Attenuators
6. Agilent E3620A DC Power Supply
7. Tektronix DMM157 Multimeter
8. Matched High-Speed Cables w/SMA Connectors
Note:
Items 1 through 3 constitute the BERT stack.

Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: SY88773V

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip SY88773V stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Microchip Manualer

Microchip

Microchip ATmega1281 Manual

19 Juli 2025
Microchip

Microchip ATtiny461 Manual

19 Juli 2025
Microchip

Microchip ATxmega128D3 Manual

19 Juli 2025
Microchip

Microchip ATxmega128D4 Manual

19 Juli 2025
Microchip

Microchip ATTINY28 Manual

19 Juli 2025
Microchip

Microchip ATTINY861 Manual

19 Juli 2025
Microchip

Microchip ATmega1280 Manual

19 Juli 2025
Microchip

Microchip ATtiny84A Manual

19 Juli 2025
Microchip

Microchip ATmega645P Manual

19 Juli 2025
Microchip

Microchip ATmega16A Manual

19 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Synology

Synology CMA-01 Manual

1 August 2025
Synology

Synology RKS-02 Manual

1 August 2025
Navman

Navman MiVue 765 SAFETY Manual

1 August 2025
Navman

Navman MY75T Manual

1 August 2025
Exquisit

Exquisit AIRFRY 3010 Manual

1 August 2025
Navman

Navman MiVue 155 SAFETY Manual

1 August 2025
Navman

Navman MiVue 698 Manual

1 August 2025
Newland

Newland FM550 Manual

1 August 2025
Tripp Lite

Tripp Lite SRIN4181810 Manual

1 August 2025
Navman

Navman MyTruck III Manual

1 August 2025