Microchip SY88992L Manual


Læs gratis den danske manual til Microchip SY88992L (7 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Microchip SY88992L, eller vil du spørge andre brugere om produktet?

Side 1/7
SY88992L Evaluation Board
3.3V, 3.2Gbps VCSEL Driver
Micrel Inc. • 2180 Fortune Drive • San Jose, CA 95131 • USA • tel +1 (408) 944-0800 • fax + 1 (408) 474-1000 • http://www.micrel.com
November 2005
M9999-111005-A
hbwhelp@micrel.com or (408) 955-1690
General Description
The SY88992L evaluation board is designed for fast
evaluation of the SY88992L VCSEL driver.
A picture of the board loaded with SY88992L is shown
below.
Data sheets and support documentation can be found
on Micrel’s web site at: www.micrel.com.
Features
Single 3.3V supply voltage
AC-coupled inputs
AC-coupled outputs
Peaking current programming
Peaking current duration programming
Related Support Documentation
SY88992L, 3.3V, 3.2Gbps VCSEL Driver data sheet
SFP_992_R0 (small form-factor pluggable optical
module)
____________________________________________________________________________________________________________________
Evaluation Board
Micrel, Inc. SY88992L Evaluation Board
November 2005
2 M9999-111005-
A
hbwhelp@micrel.com or (408) 955-1690
Evaluation Board Description and
Setting
The evaluation board consists of a four-layer FR4
board. The inputs of the driver are AC-coupled and
are accessible through SMA connectors.
Board Setting and Operation
1. Use connectors, J1 and J3, to connect a signal to
the driver’s inputs. The driver’s outputs, J2 and
J4, are to be connected to the scope.
2. Connect the power supply between TP1 (V
CC
=
3.3V) and TP5 (GND).
3. Set position 1 of the DIP switch S1 to “ON” to
enable the driver.
4. Adjust the modulation current with potentiometer
R11. The modulation current can be measured
using one of the following methods:
a. Measure the output swing on the scope
and divide it by the load (R1// 50 or R2
// 50). The board comes with a 30
load (75 // 50).
b. Measure the IM_SET voltage by
connecting a voltmeter between TP4 and
GND, and use the modulation gain curve
to deduce I
MOD.
Figure 1. Modulation Gain vs. IM_SET
Once the modulation current is set, one can use the
peaking option to improve the VCSEL edge response
by varying the peaking amplitude and duration. Use
R3 to adjust the peaking duration. Peaking amplitude
is adjusted by setting different combinations of switch
positions on the DIP switch S1, as shown in table 1
below:
IP/I
MOD
0
%
5
%
10
%
15
%
20
%
25
%
30
%
35
%
Position 2 off on off on off on off on
Position 3 off off on on off off on on
Position 4 off off off off on on on on
Table 1. Peaking/Modulation Current Ratio Setting
OFF Modulation Current Measurement
Set position 1 of the DIP switch S1 to “OFF” to disable
the driver and measure the current using the same
methods as described in step 4 of the “Board Setting
and Operation” section.


Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: SY88992L

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip SY88992L stil et spørgsmål nedenfor, og andre brugere vil svare dig