Microchip USB3330 Manual

Microchip Ikke kategoriseret USB3330

Læs gratis den danske manual til Microchip USB3330 (10 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 32 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 16.5 anmeldelser. Har du et spørgsmål om Microchip USB3330, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/10
2013 - 2015 Microchip Technology Inc. DS00001863B-page 1
INTRODUCTION
The purpose of this application note is to provide a list of items that need to be considered when designing systems that
incorporate the following categories of Microchip USB products:
• USB 2.0 Hubs
• USB 3.1 Gen 1 Hubs
• Flash Media Controllers
• Flash Media Controller Hub Combo
• USB Transceivers
The target audience of this document is system engineers and layout professionals who are familiar with industry stan-
dard practices. This application note must be used in conjunction with the device data sheet, reference design, and other
relevant application notes.
Overview
This document includes the following chapters:
•Schematic Guidelines
•Layout Guidelines
Each chapter begins with a sub-section on the general design considerations for all products. Subsequent sub-sections
detail design considerations for specific product categories and their applications. The order of these lists are arbitrary.
References
• Application Notes:
- AN 18.16, PCB Design Guidelines for USB223x/i & USB225x/i Controllers
- AN 26.2, Implementation Guidelines for Microchip’s USB 2.0 and USB 3.1 Gen 1 Hub Devices
- AN 18.15, PCB Design Guidelines for QFN and DQFN Packages
- AN 19.17, ULPI Design Guide
- WP 2.10, PCB Design for WLCSP BGA Packages
• The data sheet for the respective product(s)
• Applicable USB specifications and ECNs available at usb.org
AN 26.21
USB Device Design Checklist
Author: Rejo Titus
Microchip Technology Inc.
AN 26.21
DS00001863B-page 2 2013 - 2015 Microchip Technology Inc.
1.0 SCHEMATIC GUIDELINES
1.1 General Considerations
□ A. Confirm the pin-out functions of the schematic symbol of the USB product matches what is provided in
the product data sheet.
□ B. For designs with exposed USB connectors, connect the USB cable shield to digital ground with an RC
network. Refer to the Microchip AN 26.2 application note for additional details.
□ C. Ensure that the power rails, such as VDD12 or VDD33, are not noisy and are stable and accurate across
all power consumption ranges. Refer to the Microchip AN 26.2 application note and the product data sheets
for additional details.
□ D. RESETn should be asserted buy a supervisory circuit when either VDD12 or VDD33 are below their
thresholds or asserted under manual or host control. Refer to the Microchip AN 26.2 application note for addi-
tional details.
□ E. To use in-system OTP programming through SMBus, SM_DAT should be pulled up with an external
resistor and SM_CLK should be pulled down with an external resistor. The programmer pulls SM_CLK up
with a resistor when connected to the PCB. Refer to the Microchip AN 26.2 application note for additional
details.
□ F. Make sure that the crystal and load capacitors are chosen correctly for proper operation. Refer to the
product data sheet for additional details.
□ G. If the Microchip product has internal regulators, place regulator capacitors on the regulator pins as
described in the product data sheet.
□ H. Internal regulators of the Microchip product must have the proper input voltage. No external voltage
should be applied to the output of these internal regulators. Refer to the product data sheet for additional
details.
□ I. Place a 2.2uF capacitor on upstream Vbus to comply with the USB-IF decoupling capacitance require-
ments with margin for capacitor tolerances. Refer to the USB 2.0 Specification for additional details.
□ J. VBUS_DET should be connected to the upstream VBUS through a resistor divider for stand-alone appli-
cations. Embedded applications should actively control this pin with a 3.3V signal. Refer to the Microchip AN
26.2 application note for additional details.
□ K. The Rbias resistor must be the correct value and have, at worst, a 1% tolerance. Refer to the product
data sheet for additional information.
□ L. Pins that are identified as no connect should not be connected to any net. Refer to the product data sheet
for additional information.
□ M. Ensure that the product is configured correctly by either puling the relevant strap pins up/down appropri-
ately, or via SMBus/I2C. Refer to the product data sheet for additional information.
FIGURE 1-1: SHIELD TO DIGITAL GROUND CONNECTION

Produkt Specifikationer

Mærke: Microchip
Kategori: Ikke kategoriseret
Model: USB3330

Har du brug for hjælp?

Hvis du har brug for hjælp til Microchip USB3330 stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Microchip Manualer

Microchip

Microchip AT7913 Manual

1 September 2025
Microchip

Microchip ATmega1281 Manual

19 Juli 2025
Microchip

Microchip ATtiny461 Manual

19 Juli 2025
Microchip

Microchip ATxmega128D3 Manual

19 Juli 2025
Microchip

Microchip ATxmega128D4 Manual

19 Juli 2025
Microchip

Microchip ATTINY28 Manual

19 Juli 2025
Microchip

Microchip ATTINY861 Manual

19 Juli 2025
Microchip

Microchip ATmega1280 Manual

19 Juli 2025
Microchip

Microchip ATtiny84A Manual

19 Juli 2025
Microchip

Microchip ATmega645P Manual

19 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Elektrobock

Elektrobock PT44 Manual

14 September 2025
BSS Audio

BSS Audio FDS-366T Manual

14 September 2025
Systemair

Systemair Airline R-114 Manual

14 September 2025
IFM

IFM SU2031 Manual

14 September 2025
Morel

Morel Tempo Ultra Integra 502 Manual

14 September 2025
IMC Networks

IMC Networks 232CL9R Manual

14 September 2025
Varta

Varta Speed Charger 57955 Manual

14 September 2025
Melissa & Doug

Melissa & Doug 9336 Manual

14 September 2025
Opus

Opus dataPREDATOR Manual

13 September 2025
Varta

Varta Wireless Power Bank 20000 57909 Manual

13 September 2025