Mikrotik CAOTU Manual

Mikrotik At CAOTU

Læs gratis den danske manual til Mikrotik CAOTU (2 sider) i kategorien At. Denne vejledning er vurderet som hjælpsom af 23 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 12 anmeldelser. Har du et spørgsmål om Mikrotik CAOTU, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/2
1. Mount antenna pigtails and Ethernet insulators in their respective holes. Seal the unused
holes with the provided rubber seals H
2. Install the spacers J on the baseplate C using screws K, as in the picture. Spacers should
be placed on top of the baseplate in the positions desired (depends on the type of Router-
BOARD you will use) and fastened with screws from underneath.
3. Place the baseplate inside the case box, minding the orientation of the baseplate. Note
that if you have installed the baseplate correctly, a hole in the case will match a respective
hole in the baseplate – this hole is for the grounding screw. Install the grounding screw G
in this hole. It is supposed to go all the way through the case, where the jagged washer
and Wingnut should connect the grounding.
4. Attach the baseplate to the box with the K screws at it’s top and bottom.
5. Attach the mounting rail with the selfscrews to the bottom of the box, screw the rail to the
pre-made screw holes - this is to maintain a distance between through three washers
the box and the rail, to allow space for mounting rings (see image).
6. Place the RouterBOARD device on the baseplate and secure it with the K
screws to the previously installed spacers. Insert the ethernet cable into
the device port, and attach the pigtail to the wireless card.
7. Insert the rubber isolation cord E into the shaft near the edge of the case
cover B, and trace the cord all the way around the cover. The cord is sup-
posed to be longer than needed – you will need to cut it so that both ends
are slightly overlapping. The cord should match the ridge near the edge of
the base A. Close the case and secure the cover with the screws F.
8. Use the rings D to fasten the case on the mast. Mind the orientation: it
must be mounted with connectors down, as there are two small ventilation
holes, which must be pointed down to avoid water leaking inside the case.
Make sure to tighten the rings reliably to prevent the device shift/rotate in
high wind.
RouterBOARD Big Outdoor Case
Installation Guide and Warranty Information
This document will guide you through assembling the MikroTik Big Outdoor Case.
The following parts should be included when you receive it:
A: Box base B: Box lid C: Baseplate D: Mounting rings E: Isolation cord F: Lid screws
G: Ground screw H: Seals I: Rail and Wingnut J: Spacers K: Plate screws L: Selfscrews
Assembly instructions
Connecting External Antenna Cable (optional)
If the RouterBOARD was purchased with external antenna connector option,
screw the connector of the antenna cable cable on the appropriate antenna
attachment of the case. Hand tighten the connector (do not use vice grips for
this job). When tying the coaxial cable, make sure no water can get into it and/
or into the equipment it is attached to. It is very important to seal the connec-
tion properly with a good rubber tape made particularly for this purpose (note
that many general purpose tapes will not prevent moisture to leak into con-
nector, or will fail after some time). Note: do not bend the cable straight: you
should keep a radius of curvature allowing the cable to bend without applying
force.
Safety Precautions
IMPORTANT: LIVES MAY BE AT RISK! Contacting power lines may cause
injury or death. Make sure that in no case may equipment or personnel come
in direct or indirect contact with power lines. All overhead wiring should be
assumed to be power lines. Ensure that the mast may not contact power lines
even if it falls during or after installation. If a person comes in contact with
electricity and is not able to move, you MUST NOT touch that person to avoid
the same fate! Instead, use a known non-conductive stick or rope to pull him/her away from the electric line.
Respect safety procedures when working above the ground. Do not work alone: a friend or co-worker can save your life in case of
an accident.
Grounding
The installation infrastructure (towers and masts), as well as antennas and the device itself (there is a small screw with a wing nut
on the case with a sticker identifying chassis grounding), must be properly grounded, and lightning arrestors must be installed on
all external antenna cables (near the antennas or on the antennas themselves) to prevent equipment damage and human injury.
Note that lightning arrestors will not have any effect if not grounded. Note also that damages caused by static electricity and light-
ning are not covered by warranty.
Use 1 AWG (7mm in diameter) wire with corrosion-resistant connectors for grounding. Be sure to check that the grounding infra-
structure you use is indeed functional (as opposed to decorative-only grounding present on some sites).
Copyright and Warranty Information
Copyright and Trademarks. Copyright MikroTikls SIA. This manual contains information protected by copyright law. No part of it
may be reproduced or transmitted in any form without prior written permission from the copyright holder. RouterBOARD,
RouterOS, RouterBOOT and MikroTik are trademarks of MikroTikls SIA. All trademarks and registered trademarks appearing in
this manual are the property of their respective holders.
Hardware. MikroTikls SIA warrants all RouterBOARD series equipment for the term of one year from the shipping date to be free
of defects in materials and workmanship under normal use and service, except in case of damage caused by mechanical, electri-
cal or other accidental or intended damages caused by improper use or due to wind, rain, re or other acts of nature.
If you have purchased your product from a MikroTik Reseller, please contact the Reseller company regarding all warranty and
repair issues, the following instructions apply ONLY if you purchased your equipment directly from MikroTik Latvia
To return failed unit or units to MikroTikls you must perform the following RMA (Return Material Authorization) procedure. Follow
the instructions below to save time, efforts, avoid costs, and improve the speed of the RMA process. Take into account that all
goods have one year warranty.
Instructions are located on our webpage here: http://rma.mikrotik.com
Manual. This manual is provided “as is” without a warranty of any kind, expressed or implied, including, but not limited to, the
implied warranty of merchantability and tness for a particular purpose. The manufacturer has made every effort to ensure the
accuracy of the contents of this manual, however, it is possible that it may contain technical inaccuracies, typographical or other
errors. No liability is assumed for any inaccuracy found in this publication, nor for direct or indirect, incidental, consequential or
other damages that may result from such an inaccuracy, including, but not limited to, loss of data or prots. Please report any
inaccuracies found to support@mikrotik.com.

Produkt Specifikationer

Mærke: Mikrotik
Kategori: At
Model: CAOTU

Har du brug for hjælp?

Hvis du har brug for hjælp til Mikrotik CAOTU stil et spørgsmål nedenfor, og andre brugere vil svare dig


At Mikrotik Manualer

Mikrotik

Mikrotik CAOTU Manual

26 Juli 2024

At Manualer

Nyeste At Manualer

Osprey

Osprey Zealot 15 Manual

28 December 2024
Osprey

Osprey Xenith 88 Manual

28 December 2024
Osprey

Osprey Xenith 75 Manual

28 December 2024
Osprey

Osprey Xenith 105 Manual

28 December 2024
Osprey

Osprey Xena 85 Manual

28 December 2024
Osprey

Osprey Xena 70 Manual

28 December 2024
Osprey

Osprey Wayfarer 70 Manual

28 December 2024
Osprey

Osprey Viper 9 Manual

28 December 2024
Osprey

Osprey Viper 3 Manual

28 December 2024
Osprey

Osprey Viper 13 Manual

28 December 2024