Milwaukee 2441-20 Manual

Milwaukee Ikke kategoriseret 2441-20

Læs gratis den danske manual til Milwaukee 2441-20 (5 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Milwaukee 2441-20, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/5

52(2x)

14(10x)

14(3x)

36(2x)

35(2x)

14 37 38

39 51

48 49

50 74

60 62

1 3 5

26 76

NOTE:

Gearcase Assembly #72

contains a series of

planetary and sun

gears that are

enclosed

here.

EXAMPLE:

Component Parts (Small #)

Are Included When Ordering

The Assembly (Large #).

See detail

FIG. PART NO. DESCRIPTION OF PART NO. REQ.

1 34-80-0020 Retaining Ring (1)

3 40-50-6420 Return Spring (1)

4 45-98-0275 Clutch Yoke (1)

5 --------------- Slide Clutch (1)

10 45-88-1940 Washer (1)

11 32-40-2395 Input Gear (1)

12 36-18-0610 Input Shaft (1)

14 06-82-2025 M3.5 x 15 Pan Hd. Plastite T-10 Screw (13)

24 45-24-0920 Shuttle Lock (1)

25 28-20-2540 Left Cover (1)

26 45-88-1945 Washer (2)

27 34-80-0270 Retaining Ring (1)

32 40-50-1475 Detent Spring (1)

33 43-72-0430 Detent (1)

35 45-88-1980 Spring Washer (2)

36 05-81-0205 M3 x 6 Pan Hd. Phillips Screw (2)

37 42-70-1125 Clip (1)

38 --------------- Housing-Left (1)

39 43-98-0570 Speed Dial (1)

40 34-80-1120 Retaining Ring (1)

41 32-40-0800 Input Gear (1)

45 40-50-1635 Spring (1)

46 23-38-0625 EOT Actuator (1)

47 31-01-1725 Light Pipe with fuel gauge label (1)

48 --------------- Battery Contact Plate Assembly (1)

49 --------------- Switch (1)

50 --------------- PCB Assembly (1)

51 --------------- Housing-Right (1)

52 05-88-0985 M3.5 x 26 Pan Hd. Phillips Screw (2)

53 05-88-1610 M3.5 x 10 Pan Hd. T-10 Screw (1)

55 42-52-0440 Cartridge Mounting Cap (1)

56 45-88-2640 Wave Washer (1)

57 45-88-1495 Flat Washer (1)

58 06-55-0900 Hex Nut (1)

59 44-70-0330 Plunger (1)

60 45-04-2015 M5 x .8 Flat Hd. Phillips Screw (2)

61 31-01-1910 10 Oz. Cartridge Holder (1)

54-06-2460

M12™ CORDLESS CAULK and ADHESIVE GUN

E34A2441-20 SEE PAGE 5

REVISED BULLETIN

SERVICE PARTS LIST

BULLETIN NO.

WIRING INSTRUCTION

DATE

CATALOG NO.

SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS

SERIAL

NUMBER

MILWAUKEE ELECTRIC TOOL CORPORATION

13135 W. LISBON RD., BROOKFIELD, WI 53005

Drwg. 4

Feb. 2014

FIG. PART NO. DESCRIPTION OF PART NO. REQ.

62 44-94-0490 10 Oz. Rack (1)

63 31-44-3170 Rack Handle (1)

65 42-70-0055 Housing Connection Clip (1)

66 31-44-3175 Handle Assembly (1)

67 28-20-0310 Right Cover Assembly (1)

68 23-66-3135 Switch Assembly (1)

69 44-94-0495 10 Oz. Rod Assembly (1)

70 14-08-0240 Clutch Gear Assembly (1)

72 14-30-0400 Gearcase Assembly (1)

73 14-29-0725 Output Gear Assembly (1)

74 --------------- EOT Switch (1)

75 23-30-0950 Motor Assembly with Drive Hub (1)

76 --------------- Output Gear Assembly (1)

77 12-20-2441 Service Nameplate (1)

78 10-20-3672 Warning Label (1)

See page 4

for additional

cartridge systems

42-70-0058

Improved

Design

Original

Design

42-70-0055

M12™ tools utilize two different Housing

Connection Clip designs depending on the

Handle Set . See page two for details.

42-70-0055

42-70-0058

Recess in early handle

sets may only have the

slots to accommodate a

housing clip. Use 42-70-0055

only in this situation.

Slots

Recess in newer handle

sets have two slots, a

dimple and a tab cavity to

accommodate the newer

housing clip design.

Slots

Dimple

Tab Cavity

Updated M12™ Handle Sets utilize Housing

Connection Clips No. 42-70-0055 and 42-70-

0058. (The 42-70-0058 is a preferred upgrade).

Install this clip design by aligning the side rails

of the clip with the two slots in the handle set.

Gently push into place with the aid of a small

flat blade screwdriver or a similar instrument.

Be sure that the clip is properly seated in both

slots and that the tab of the clip snaps down in

the round dimpled cavity of the handle set. Be

sure that the clip is flush to sub-flush to the end

of the handle set. To remove the clip, use the

same small flat blade screwdriver or a similar

instrument and lift up on the clip tab while

pushing the clip out of the handle set. Use a

needle nose pliers to gently rebend the clip tab

if necessary. If the tab on the clip is damaged

during this process and is loose or will not stay

in place, replace with a new 42-70-0058 clip.

Early M12™ Handle Sets utilize Housing

Connection Clip No. 42-70-0055. Install this

clip design by aligning the side rails of the clip

with the two slots in the handle set. Gently

push into place with the aid of a small flat

blade screwdriver or a similar instrument. Be

sure that the clip is properly seated in both

slots and that the clip is flush to sub-flush to

the end of the handle set. To remove the clip,

use the same small flat blade screwdriver or a

similar instrument and push the clip out of the

handle set. If the clip is loose or will not stay in

place, a needle nose pliers can be used to

gently bend/pinch the side rails of the clip. If

the clip is damaged do not use, replace with a

new 42-70-0055 housing clip.

Slots

Dimples

Recess in this

handle set design

has slots and dimples

to secure a housing clip.

The 42-70-0055 can be

used but the 42-70-0058 is

preferred in this situation.

Newer M12™ Handle Sets utilize Housing

Connection Clip No. 42-70-0058. Install this

clip design by aligning the side rails of the clip

with the two slots in the handle set. Gently

push into place with the aid of a small flat blade

screwdriver or a similar instrument. Be sure

that the clip is properly seated in both slots and

that the tab of the clip snaps down in the

rectangular cavity of the handle set. Be sure

that the clip is flush to sub-flush to the end of

the handle set. To remove the clip, use the

same small flat blade screwdriver or a similar

instrument and lift the clip tab out of the cavity

while pushing the clip out of the handle set.

Use a needle nose pliers to gently rebend the

clip tab if necessary. If the tab on the clip is

damaged during this process and is loose or

will not stay in place, replace with a new

42-70-0058 clip.

Produkt Specifikationer

Mærke:	Milwaukee
Kategori:	Ikke kategoriseret
Model:	2441-20

Har du brug for hjælp?

Hvis du har brug for hjælp til Milwaukee 2441-20 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Milwaukee Manualer

Milwaukee M18 RADIUS 2145-20 Manual

13 August 2025

Milwaukee 6101 Manual

13 August 2025

Milwaukee M12 2446-20 Manual

13 August 2025

Milwaukee M12 Fuel 2522-20 Manual

13 August 2025

Milwaukee M18 RADIUS ONE-KEY 2147-20 Manual

13 August 2025

Milwaukee M18 HAMMERVAC 2712-DE Manual

13 August 2025

Milwaukee M12 2456-20 Manual

13 August 2025

Milwaukee M12 2472-20 Manual

13 August 2025

Milwaukee M12 3150-20 Manual

13 August 2025

Milwaukee HAMMERVAC M18 M28 49-90-2342 Manual

13 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Mueller AS 10.00 knx Manual

18 August 2025

Ecler VEO-XRT44 Manual

18 August 2025

Daikin RRDQ220V1 Manual

18 August 2025

MSW -C&A HP MX2 Manual

17 August 2025

Schellenberg Smart Drive 10 Premium Manual

17 August 2025

Intergas Xclusive 30 Manual

17 August 2025

Ambient Weather WS-1553-IP Manual

17 August 2025

Mars Gaming MF-PWMX2 Manual

17 August 2025

Daikin RXL20K3V1B Manual

17 August 2025

Taiji HC-18F Manual

17 August 2025