Milwaukee 48-22-8860 Manual

Milwaukee Ikke kategoriseret 48-22-8860

Læs gratis den danske manual til Milwaukee 48-22-8860 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 12 personer og har en gennemsnitlig bedømmelse på 3.6 stjerner ud af 6.5 anmeldelser. Har du et spørgsmål om Milwaukee 48-22-8860, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

IMPORTANT SAFETY INSTRUCTIONS

WARNING

READ AND UNDERSTAND ALL

INSTRUCTIONS. Failure to follow

all instructions listed below, may result in serious

personal injury and property damage. SAVE THESE

INSTRUCTIONS

• Do not use for personal fall protection.

• For use by trained personnel only. Users must

be knowledgeable in tool safety and use of tools

in "off the ground" situations.

• Use only with energy absorbing lanyards.

Ropes, straps or chains may break and cause

failure. Do not use with lanyards at full tension.

• Keep out of the reach of children.

• Do not exceed maximum capacity marked on

the attachment accessory label. Exceeding

maximum capacity may result in serious injury

or death.

• Always follow these installation instructions,

including wrapping and length requirements.

• Do not use attachment accessories and self-

adhering tape in temperatures below -40°F

(-40°C) or above 150°F (65° ).c

• Use only the continuous length of self-adher-

ing tape required. Do not splice two lengths of

tape together to make the required length.

• Inspect attachment accessory before each use.

Replace damaged attachment accessories im-

mediately. Ensure the fabric is not cut, ripped

or frayed, and stitching is not damaged.

• Inspect self-adhering tape before each use.

Remove and re-tape if damaged, loose, rolled,

bunched, wrinkled, or attachment accessory

has moved/slipped along the tool or out of the

tape.

•Inspect self-adhering tape if tool has been

dropped or the tape has been impacted. Re-

place if tape has ripped, slipped, or wrinkled.

• Use only with tools that meet the attachment

accessory specifications. Never modify tools to

create attachment points. Do not attach to tool

in a way that keeps guards, switches or locks

from operating properly. Do not use on tapered

or smooth handled tools where the tape could

slide off the end.

• Do not use attachment accessories near sharp

or rough edges that could cut or fray.

• Do not use near caustic substances.

• Keep surfaces dry, clean and free from oil and

grease. Dirty surfaces will not allow self-adhering

tape to grip properly.

• Do not alter attachment accessories or use in a

manner other than as instructed. Only connect

to tools in the manner described.

• Do not tie knots in attachment accessory or

attach attachment accessory back onto itself.

• Do not increase attachment accessory length.

Do not connect to strings, ropes, or additional

attachment accessories.

•Do not secure attachment accessories to move-

able objects, such as ladders or toolboxes.

Moveable objects can pull user off balance

when moved or shifted. Dropped tools will

swing and bounce on the attachment acces-

sory, which can pull objects over.

• For tools over 5 lb, do not secure lanyard to

yourself. Dropped tools will swing and bounce

on the attachment accessory, which can cause

loss of balance.

• Only use attachment accessories on surfaces

wider than the attachment accessory, or with a

diameter wider than the attachment accessory.

• Use Split Ring accessory only in designated

attachment points of the tool. Do not drill holes

or modify tools to use with split rings.

• Inspect Split Ring before each use. Replace

Split Ring if bent or deformed.

• Do not secure attachment accessory on re-

movable parts such as batteries, side handles,

guards, or accessories. Ensure removable

parts are secured to their base tool before

installing attachment accessory.

• After installation, ensure the attachment acces-

sory does not interfere with the operation of the

product, including guards.

• Do not use near moving parts or machinery. At-

tachment accessory could become entangled,

causing a serious hazard.

• Do not carry tools by the attachment accessory.

• Do not use to tow objects.

GENERAL USE AND CARE

Use MILWAUKEE Attachment accessories and Self-

Adhering Tape to help reduce the risks associated

with dropped tools.

1. Select the appropriate attachment accessory for

the tool.

2. Using the Taping Specications chart, cut the

required length of self-adhering tape for the at-

tachment accessory/tool combination. CAUTION!

When using energy absorbing lanyards other than

MILWAUKEE energy absorbing lanyards, use

double the length of tape to attach attachment

accessories.

3. When using the 48-22-8823 lanyard accessory,

use the appropriate underwrapping of tape to

ensure secure attachment to the tool.

4. Lay the attachment accessory on the tool so

the tape will be at least 1" away from end of

the tool. Place the attachment accessory so the

folded ends face up, away from the tool. When

using MILWAUKEE attachment accessories with

sliding barrel lock, secure the loop around the

tool and tighten the barrel lock. The barrel lock

is the wedge end of the attachment accessory.

WARNING! Do not secure attachment acces-

sory on removable parts such as batteries, side

handles, guards, or accessories.

5. Starting at the wedge end, make the required

number of complete wraps, pulling off the plastic

wrap as you go. For best results, stretch the self-

adhering tape firmly as it is applied. WARNING!

Do not wrap over wedge. Only wrap between

wedge and D-ring or body ends.

6. Begin moving down the attachment accessory,

overlapping 1/2 the tape width per wrap until the

D-ring end is reached.

7. To nish the taping, complete the required number

of wraps at the D-ring end. After inWARNING! -

stallation, ensure the attachment accessory does

not interfere with the operation of the product,

including guards.

8. If additional tape is left once the specified taping

method is complete, continue to tape along the

attachment accessory.

9. Rub the self-adhering tape to fully bond it.

ACCESSORIES

For a complete listing of accessories, go online to

www.milwaukeetool.com or contact a distributor.

TAPING LOCATIONS

EMPLACEMENTS DE L’ENVELOPPE

LUGARES DÓNDECOLOCAR LA CINTA

Wedge end

Extrême à coin

Extremo de la cuña

Barrel lock

(Wedge end)

Barillet de serrure

(extrême à coin)

Cierre de barril

(extremo de la cuña)

D-ring end

Extrême de bague en D

Extremo de la argolla en D

Overlap

Chevauchement

Sobreponga

Underwrap

Crémaillère

Cremallera

When using

Lors de l’emploi du modèle

Al usar el modelo

48-22-8823

2nd set of wraps

Deuxième tour d’enveloppage

2do conjunto de coberturas

Overlap

Chevauchement

Sobreponga

1st set of wraps

Première tour d’enveloppage

1er conjunto de coberturas

Wedge end

Extrême à coin

Extremo de la cuña

D-ring end

Extrême de bague en D

Extremo de la argolla en D

Minimum 1"

Minimum de 25 mm

Mínimo 25 mm

TAPING SPECIFICATIONS FOR

MILWAUKEE SELF-ADHERING

TAPE CAT. NO. 48-22-8860

Taping Methods

1 X 1 : Cut the recommended length of tape.

Make 1 complete wrap at the wedge end.

Overlap by 1/2 the tape width until the

D-ring/body end is reached.

Make 1 more complete wrap.

2 X 2 : Cut the recommended length of tape.

Make 2 complete wraps at the wedge end

Overlap by 1/2 the tape width until the

D-ring/body end is reached.

Make 2 more complete wraps.

3 X 3 : Cut the recommended length of tape.

Make 3 complete wraps at the wedge end

Overlap by 1/2 the tape width until the

D-ring/body end is reached.

Make 3 more complete wraps.

Accessory

Accessoire

Accesorio de

sujeción

Tool Weight

Poids

Peso de la

herramienta

Handle Diameter / Diamètre de la poignée / Diámetro del mango

0.5" *

13 mm

> 0.5" - 1"

> 13 mm - 25 mm

> 1" - 1.5"

> 25 mm - 38 mm

> 1.5" - 2"

> 38 mm - 51 mm

> 2" - 2.5"

> 51 mm - 64 mm

48-22-8870 ≤ 2 lb (0.9 kg)

Tape length 11" (28 cm) 17" (43 cm) 26" (66 cm) 31" (79 cm) 42" (107 cm)

Taping Method

2 x 2 2 x 2 2 x 2 2 x 2 2 x 2

48-22-8871 ≤ 5 lb (2.3 kg)

Tape length 18" (46 cm) 28" (71 cm) 40" (102 cm) 53" (135 cm) 70" (178 cm)

Taping Method

3 x 3 3 x 3 3 x 3 3 x 3 3 x 3

48-22-8822 ≤ 5 lb (2.3 kg)

Tape length 31" (79 cm) 38" (97 cm) 41" (102 cm)

N/R (P/R) N/R (P/R)

Taping Method

3 x 3 3 x 3 3 x 3

48-22-8823 ≤ 10 lb (4.5 kg)

Underwrap

Tape length 25" (64 cm) 38" (97 cm) 40" (102 cm) 45" (114 cm)

N/R (P/R)

Underwrap

Taping Method 1 x 1 1 x 1 1 x 1 1 x 1

Tape length 32" (81 cm) 43" (109 cm) 52" (132 cm) 48" (122 cm)

N/R (P/R)

Taping Method

3 x 3 3 x 3 3 x 3 3 x 3

CAUTION

The above chart is for use with

MILWAUKEE attachment accesso-

ries, lanyards, and self-adhering tape. When using

attachment accessories other than MILWAUKEE

attachment accessories with MILWAUKEE self-ad-

hering tape, follow all manufacturer's recommended

attachment methods. Secure MILWAUKEE attach-

ment accessories ONLY with MILWAUKEE self-

adhering tape.

N/R = Not Recommended. Do not use in this

combination.

* Do not use on products with a surface less than

the width of the attachment accessory, or less

than 0.5" (13 mm) diameter.

SPÉCIFICATIONS D’ENVELOPPAGE

POUR LE RUBAN AUTO-COLLANT

MILWAUKEE NO DE CAT. 48-22-8860

Processus d’enveloppage

1 X 1 : Couper le ruban à la longueur désirée. Faire

1 tour complète autour de l’extrême à coin.

Chevaucher la moitié du ruban jusqu’à ce

que vous arrivez à l’extrême du corps/bague

en D. Faire tour complète additionnelle.1

2 X 2 : Couper le ruban à la longueur désirée.

Faire 2 tours complètes autour de l’extrême

à coin. Chevaucher la moitié du ruban

jusqu’à ce que vous arrivez à l’extrême du

corps/bague en D. Faire tours complètes 2

additionnelles.

3 X 3 : Couper le ruban à la longueur désirée.

Faire 3 tours complètes autour de l’extrême

à coin. Chevaucher la moitié du ruban

jusqu’à ce que vous arrivez à l’extrême du

corps/bague en D.

Faire 3 tours complètes

additionnelles.

PRÉCAUTION

Le tableau ci-dessus doit être

utilisé avec les accessoires de

fixation, les longes et le ruban auto-collant

MILWAUKEE. Lors de l’utilisation d’accessoires de

xation diérents à ceux conçus par MILWAUKEE

avec le ruban auto-collant MILWAUKEE, veuillez

suivre tous les processus de xation suggérés par le

fabriquant. Fixer les accessoires de fixation

MILWAUKEE SEULEMENT avec le ruban auto-col-

lant MILWAUKEE.

P/R = Pas Recommandé. Ne pas l’utiliser avec cette

combinaison.

* Ne pas l’utiliser avec de produits dont leurs sur-

faces soient plus longues que celle de l'accessoire

de xation ou bien, moins longues que le diamètre

de 13 mm (0.5").

ESPECIFICACIONES DE CINTA

PARA LA CINTA AUTOADHERIBLE

MILWAUKEE CAT. NO. 4822-8860

Métodos para colocar cinta

1 X 1 : Corte la longitud recomendada de cinta. Re-

alice 1 cobertura completa en el extremo de

la cuña. Sobreponga en 1/2 de longitud de

cinta hasta que se alcance el extremo de la

argolla en D/cuerpo. Realice cobertura com1-

pleta más.

2 X 2 : Corte la longitud recomendada de cinta. Re-

alice 2 coberturas completas en el extremo

de la cuña. Sobreponga en 1/2 de longitud

de cinta hasta que se alcance el extremo de

la argolla en D/cuerpo. Realice coberturas 2

completas más.

3 X 3 : Corte la longitud recomendada de cinta. Re-

alice 3 coberturas completas en el extremo

de la cuña. Sobreponga en 1/2 de longitud

de cinta hasta que se alcance el extremo de

la argolla en D/cuerpo. Realice coberturas 3

completas más.

PRECAUCIÓN

La tabla anterior es para utili-

zarse con accesorios de su-

jeción de MILWAUKEE, acolladores y cinta autoad-

herible. Cuando utilice accesorios de sujeción que

no sean de MILWAUKEE con cinta autoadherible de

MILWAUKEE, siga todos los métodos de sujeción

recomendados del fabricante. Fije los accesorios de

sujeción MILWAUKEE SOLO con cinta autoadherible

MILWAUKEE.

N/R = No se recomienda. No utilice en esta com-

binación.

* No lo utilice en productos con una supercie

menor que el ancho del accesorio de sujeción o

con un diámetro menor de 13 mm (0.5").

Produkt Specifikationer

Mærke:	Milwaukee
Kategori:	Ikke kategoriseret
Model:	48-22-8860

Har du brug for hjælp?

Hvis du har brug for hjælp til Milwaukee 48-22-8860 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Milwaukee Manualer

Milwaukee MX Fuel MXF002 Manual

15 December 2025

Milwaukee 48-22-9200 Manual

15 December 2025

Milwaukee 48-22-8586 Manual

15 December 2025

Milwaukee M18 Fuel HTIW ONE-KEY 2865-20 Manual

11 December 2025

Milwaukee M12 Trapsnake 2577-21 Manual

11 December 2025

Milwaukee MX FUEL MXF501 Manual

3 November 2025

Milwaukee MX FUEL MXF500 Manual

2 November 2025

Milwaukee MVA-2 Manual

8 Oktober 2025

Milwaukee 4932479730 Manual

16 September 2025

Milwaukee WT 10 Manual

16 September 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kenmore HV3006 Manual

1 Januar 2026

Asus ROG RYUJIN III WB Manual

1 Januar 2026

Asus ROG Strix XF 120 Manual

31 December 2026

Arturia Bus Transient Manual

31 December 2026

IQAir Mask Manual

31 December 2026

SPT SU-2550W Manual

31 December 2026

NUX Metal Core Deluxe Manual

31 December 2026

Samsung AQ12FGN Manual

31 December 2026

Reflecta PLANO Flat Extend 105-10060T Manual

31 December 2026

Blaupunkt MPA 14120 H Manual

31 December 2026