Milwaukee 6792-20 Manual

Milwaukee bore 6792-20

Læs gratis den danske manual til Milwaukee 6792-20 (12 sider) i kategorien bore. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Milwaukee 6792-20, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/12

Cat. No. / No de cat.

6580-20, 6740-20, 6742-20, 6780-20,

6790-20, 6791-20, 6791-21, 6792-20

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

WARNING To reduce the risk of injury, user must read and understand operator's manual.

AVERTISSEMENT Aﬁ n de réduire le risque de blessures, l'utilisateur doit lire et bien

comprendre le manuel.

ADVERTENCIA Para reducir el riesgo de lesiones, el usuario debe leer y entender el manual.

HEAVY-DUTY SCREWDRIVER

EXTRA ROBUSTE TOURNEVIS

DESTORNILLADORES HEAVY-DUTY

Installing and Removing Bits

TEKS Ramp-O Locator Assembly

The locator assembly must

Magnetic socket

Locator

Ramp-o

sleeve

be removed when chang-

ing bit sizes.

1. Unplug tool. To remove

the locator assembly,

t u r n t h e r a mp-off

sleeve while pulling it

away from the tool.

2. Pull out the magnetic

socket and replace it with a new socket.

3. Push the locator assembly onto the nose of the

tool until it snaps into place.

Installing and Removing Bits

Drywall Ramp-O Locator Assembly

Bit holder

Insert bit

Locator

Ramp-o

sleeve

1. Unplug tool. To remove the locator assembly, turn

the ramp-o sleeve while pulling it away from the

tool.

2. Push insert bit into bit holder until it snaps into

place. Push the bit holder into the nose of the tool

until it snaps into place.

3. Push the locator assembly onto the nose of the

tool until it snaps into place.

Installing and Removing Magnetic

Sockets on Adjustable Screwdrivers

For Cat. No. 6580-20

1. Unplug tool.

2. To remove the magnetic socket, slide the locking

sleeve forward and pull out the socket.

Locking sleeve

Socket

3. To install the magnetic socket, slide the locking

sleeve forward and push in the socket until it is

fully seated.

For Cat. No. 6780-20

1. Unplug tool.

2. To remove the magnetic socket, slide the locking

sleeve forward and pull out the socket.

Locking sleeve

Socket

3. To install the magnetic socket, simply push in the

socket until it snaps into place.

OPERATION

WARNING

To reduce the risk of injury, always

wear safety goggles or glasses

with side shields.

Using Forward/Reverse Switch

1. For forward (clockwise)

Forward

Trigger

Reverse

Switch

Front of Tool

rotation, push the for-

ward/reverse switch to

the left position as

shown.

2. For reverse (coun-

terclockwise) rotation,

push the forward/re-

verse switch to the right

position as shown.

Although an interlock

prevents reversing the

tool while the motor

is running, allow it to

come to a full stop be-

fore reversing.

WARNING

To reduce the risk of injury, keep

hands and cord away from the bit

and all moving parts.

Starting, Stopping and Controlling Speed

1. To start the tool, pull the trigger.

2. To stop the tool, release the trigger.

3. To vary the drilling speed, simply increase or

decrease pressure on the trigger. The further the

trigger is pulled, the greater the speed.

Locking Trigger

The lock button holds the trigger in the ON position

for continuous full speed use.

1. To lock the trigger, hold the lock button in while

pulling the trigger. Release the trigger.

2. To unlock the trigger, pull the trigger and release.

The lock button will pop out.

Adjusting Locator Assembly

The locator assembly controls the tool's driving

depth. These screwdrivers feature a locator assembly

with one-handed depth adjustment. Depth adjust-

ments can be made easily and quickly by turning

the locator with one hand. Detents inside the sleeve

“lock” the selected depth.

For the drywall ramp-o locator assembly, start with

about 1/16" clearance between the head of the screw

and nose with the snap-action clutch disengaged

as shown.

For both locator assemblies, the

1/16"

detents on the inside of the

sleeve represent different

depths. Every two clicks of the

locator equal 1/64". Continue

adjusting the locator to the

desired depth.

1. To increase the driving

depth, simply rotate the loca-

tor in the direction labeled .

2. To decrease the driving

depth, simply rotate the loca-

tor in the direction labeled .

The detents “lock” the locator

in place, ensuring an accurate depth setting.

3. To remove the locator assembly, turn the ramp-o

sleeve while pulling it away from the tool. Reat-

taching the locator assembly will not change the

depth setting.

SPECIFICATIONS

Volts .............................................................120 AC

Amps ..................................................................6.5

Cat. No. ..................................................... 6580-20

RPM ............................................................ 0 -1200

Cat. No. ..................................................... 6740-20