Milwaukee M18 Fuel 2707-20 Manual

Milwaukee bore M18 Fuel 2707-20

Læs gratis den danske manual til Milwaukee M18 Fuel 2707-20 (6 sider) i kategorien bore. Denne vejledning er vurderet som hjælpsom af 40 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 20.5 anmeldelser. Har du et spørgsmål om Milwaukee M18 Fuel 2707-20, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/6

OPERATOR'S MANUAL

MANUEL de L'UTILISATEUR

MANUAL del OPERADOR

Cat. No.

No de cat.

2707-20

2708-20

M18™ FUEL™ HOLE HAWG™ RIGHT ANGLE DRILLS

PERCEUSE HOLE HAWG™ M18™ FUEL™ DE ÉLECTRICIEN

TALADRO HOLE HAWG™ DE M18™ FUEL™ PARA ELECTRICISTAS

TO REDUCE THE RISK OF INJURY, USER MUST READ AND UNDERSTAND OPERATOR'S

MANUAL.

AFIN DE RÉDUIRE LE RISQUE DE BLESSURES, L'UTILISATEUR DOIT LIRE ET BIEN

COMPRENDRE LE MANUEL DE L'UTILISATEUR.

PARA REDUCIR EL RIESGO DE LESIONES, EL USUARIO DEBE LEER Y ENTENDER EL

MANUAL DEL OPERADOR.

ASSEMBLY

WARNING Recharge only with the

charger speciﬁ ed for the battery. For speciﬁ c

charging instructions, read the operator’s

manual supplied with your charger and battery.

Inserting/Removing the Battery

To remove the battery, push in the release buttons

and pull the battery pack away from the tool.

To insert the battery, slide the pack into the body of

the tool. Make sure it latches securely into place.

OPERATION

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

Bit Selection

• Use sharp bits. Sharp bits are less likely to bind

when drilling.

• Use the proper bit for the job. There are many

types of bits designed for speciﬁ c purposes. Check

the information on the bit's packaging for proper

usage.

• Do not use bits larger than the rated capacity of

the drill. Gear damage or motor overload may

result (see "Speciﬁ cations").

Installing Bits

Always remove the battery before inserting or

removing bits. Select the proper style and size bit

for the application.

Installing Bits into Keyed Chucks

(Cat. No 2707-20)

1. Remove the battery pack.

2. Open the chuck jaws wide

enough to insert the bit. Be

sure the bit shank and chuck

jaws are clean. Dirt particles

may prevent the bit from lin-

ing up properly.

3. Insert the bit into the chuck. Center the bit in the

chuck jaws and lift it about 1/16" off of the bottom.

Tighten the chuck jaws by hand to align the bit.

4. Place the chuck key in each of the three holes

in the chuck, turning it clockwise to tighten the

chuck securely.

NOTE: Never use a wrench or means other than

a chuck key to tighten or loosen the chuck.

5. To remove the bit, insert the chuck key into

one of the holes in the chuck and turn it coun-

terclockwise.

Installing Bits into 7/16" Hex Chuck

(Cat. No 2708-20)

1. Remove the battery pack.

2. To attach an accessory, press the shank into the

hex drive chuck.

3. To remove the accessory, pull out the ring and

remove the accessory. Release the ring.

Bit binding

If the bit binds, the drill will suddenly react in the

opposite direction of the rotation of the bit. Reduce

the chances of a sudden reaction by following the

instructions listed below. Prepare for a sudden

reaction by holding or bracing securely.

To reduce the chance of bit binding:

• Use sharp bits. Sharp bits are less likely to bind

when drilling.

• Use the proper bit for the job. There are many

types of bits designed for speciﬁ c purposes.

• Keep selfeed bits aligned with the work surface

so bits go in straight (see "Drilling").

• Avoid drilling warped, wet, knotty, and/or pitchy

material if possible.

• Avoid drilling in material that you suspect contains

hidden nails or other things that may cause the bit

to bind.

The direction of reaction is always opposite of the

direction of bit rotation. Reaction is even more likely

to occur when enlarging already existing holes and

at the point when the bit breaks through the other

side of the material.

If the bit does bind:

1. Release the trigger immediately.

2. Reverse the motor.

3. Remove the bit from the work and start again.

4. Do not pull the trigger on and o to attempt to

start a stalled bit. This will damage the drill.

WARNING To reduce the risk of injury,

wear safety goggles or glasses with side

shields.

WARNING To reduce the risk of per-

sonal injury when drilling, hold the tool by isu-

lated gripping surfaces when performing an

operation where the cutting tool may contact

hidden wiring. Contact with a "live" wire will

make exposed metal parts of the tool "live"

and shock the operator

WARNING To reduce the risk of injury,

hold or brace securely. Always be prepared

for bit binding and drill reaction.

WARNING Always remove battery

pack before changing or removing acces-

sories. Only use accessories specifically

recommended for this tool. Others may be

hazardous.

Bracing for forward rotation

When drilling in forward, the bit will rotate in a

clockwise direction. If the bit binds in the hole, the

bit will come to a sudden stop and drill will suddenly

react in a counterclockwise direction.

The following ﬁ gure shows an example of properly

bracing the tool for forward rotation.

A. Forward (clockwise) rotation

B. Reaction

C. Brace drill with motor housing here

If the bit binds, the motor housing braced against

the stud will hold the drill in position.

WARNING To reduce the risk of injury,

keep hands away from the bit and all moving

parts.

Bracing for reverse rotation

When drilling in reverse, the bit will rotate in a coun-

terclockwise direction. If the bit binds in the hole,

the bit will come to a sudden stop and the drill will

suddenly react in a clockwise direction.

The following ﬁ gure shows an example of properly

bracing the tool for reverse rotation.

A. Reverse (counterclockwise) rotation

B. Reaction

C. Brace drill with motor motor housing here

If the bit binds, the motor housing braced against

the stud will hold the drill in position.

Using Control Switch

The control switch may be set to three positions:

forward, reverse and lock. Due to a lockout mecha-

nism, the control switch can only be adjusted when

the trigger is not pulled. Always allow the motor to

come to a complete stop before using the control

switch.

For Forward (clockwise) rotation, push the control

switch from the left side of the tool. Check the

direction of rotation before use.

For Reverse (counterclockwise) rotation, push the

control switch from the right side of the tool. Check

direction of rotation before use.

To Lock the trigger, push the control switch to

the center position. The trigger will not work while

the control switch is in the center locked position.

Always lock the trigger or remove the battery pack

before performing maintenance, changing acces-

sories, storing the tool and any time the tool is not

in use.

Starting, Stopping and Controlling Speed

These tools may be operated at any speed from

0 to full speed.

1. To start the tool, pull the trigger.

NOTE: An LED is turned on when the trigger is

pulled.

2. To vary the driving speed, increase or decrease

pressure on the trigger. The further the trigger is

pulled, the greater the speed.

3. To stop the tool, release the trigger.

Produkt Specifikationer

Mærke:	Milwaukee
Kategori:	bore
Model:	M18 Fuel 2707-20

Har du brug for hjælp?

Hvis du har brug for hjælp til Milwaukee M18 Fuel 2707-20 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

bore Milwaukee Manualer

Milwaukee M18 FPD Manual

1 Oktober 2024

Milwaukee 5376-20 Manual

30 September 2024

Milwaukee 0756-22 Manual

20 September 2024

Milwaukee PH 30 Power X Manual

12 September 2024

Milwaukee 5426-21 Manual

11 September 2024

Milwaukee M12 Fuel 3403-22 Manual

9 September 2024

Milwaukee M18 FHACOD32 Manual

3 September 2024

Milwaukee M18 ONEFHP Manual

3 September 2024

Milwaukee M18 ONEFH Manual

3 September 2024

Milwaukee M18 CHM Manual

3 September 2024

bore Manualer

Nyeste bore Manualer

Einhell BM-G1100 E Manual

14 Oktober 2024

Sun Joe 24V-DDK-LTX-PNK Manual

14 Oktober 2024

DeWalt DWD450 Manual

14 Oktober 2024

Rupes BH 252R Manual

13 Oktober 2024

Makita DHR263ZJ Manual

12 Oktober 2024

Makita HP2070 Manual

12 Oktober 2024

Makita DDA350RFJ Manual

7 Oktober 2024

Einhell TE-ID 750/1 E Manual

7 Oktober 2024

Makita HP332D Manual

7 Oktober 2024

Makita M6501 Manual

6 Oktober 2024