Mitsubishi Diamond LT-55265 Manual

Mitsubishi TV Diamond LT-55265

Læs nedenfor 📖 manual på dansk for Mitsubishi Diamond LT-55265 (104 sider) i kategorien TV. Denne guide var nyttig for 11 personer og blev bedømt med 4.5 stjerner i gennemsnit af 2 brugere

Download PDF
Side 1/104
IMMERSIVE SOUND LED LCD HDTV
with Integrated Sound Projector
MODELS
154 Series
164 Series
265 Series
OWNER’S GUIDE
For questions:•
Visit our website at www.mitsubishi-tv.com. -
E-mail us at MDEAservice@mdea.com. -
Call Consumer Relations at - 800-332-2119 for operational or connection assistance.
For information on • System Reset, please see the back cover.
To order replacement or additional remote controls, visit our website at www.mitsuparts.com or call •
800-553-7278.
265 Series.• IR emitter cables for NetCommand home-theater control are available for purchase from
Mitsubishi.
Call 800-553-7278 and
request either part number 242D483020 (two-ended cable) or part
number 299P254020 (four-ended cable).
®
For assistance call 1(800) 332-2119
FCC Declaration of Conformity
Product: LCD Flat Panel HDTV
Models: LT-55154
LT-40164, LT-46164, LT-55164
LT-46265, LT-55265
Responsible
Party:
Mitsubishi Digital Electronics
America, Inc.
9351 Jeronimo Road
Irvine, CA 92618-1904
Telephone: (800) 332-2119
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1)
This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
Note: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential instal-
lation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may
cause harmful interference to radio communica-
tions. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this
equipment does cause harmful interference to radio
or television reception, which can be determined
by turning the equipment off and on, the user is
encouraged to try to correct the interference by one
or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and the receiver.
- Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV
technician for help.
Changes or modifications not expressly
approved by Mitsubishi could cause harmful
interference and would void the user’s authority
to operate this equipment.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK, DO NOT REMOVE COVER (OR BACK).
NO USER SERVICEABLE PARTS INSIDE. REFER
SERVICING TO QUALIFIED SERVICE PERSONNEL.
WARNING: To reduce the risk of fire or electric shock,
do not expose this apparatus to rain or moisture.
This apparatus shall not be exposed to dripping or
splashing and no objects filled with liquids, such as
vases, shall be placed on the apparatus.
WARNING: This product contains chemicals known
to the State of California to cause cancer and/or birth
defects or other reproductive harm.
TV WEIGHT: This TV is heavy. Exercise extreme care
when lifting or moving it. Lift or move the TV with a
minimum of two adults. To prevent damage to the TV,
avoid jarring or moving it while it is turned on. Always
power off your TV, unplug the power cord, and discon-
nect all cables before moving it.
Note: Features and specifications described in this
owner’s guide are subject to change without notice.
WARNING: T
his product shall be connected to a MAINS
socket outlet with a protective earthing connection.
MAINS DISCONNECTION: The mains plug is used
as the disconnect device. The mains plug shall remain
readily operable.
The lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user of the presence of uninsulated
“dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to consti-
tute a risk of electric shock to persons.
The exclamation point within an equilat-
eral triangle is intended to alert the user to
the presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the product.
For assistance call 1(800) 332-2119
Contents
Important Information About Your TV
Installation and Operating Notes . . . . . . . . . . . . . 4
Important Safety Instructions . . . . . . . . . . . . . . . . 5
Stand Installation ......................... 6
Wall-Mounting ........................... 7
1 Basic Setup and Operation
Package Contents ....................... 9
Before You Begin ....................... 10
First-Time Power-On ..................... 10
TV Controls ........................... 11
Remote Control ..................... 11
The OLS Key and MenuTO . . . . . . . . . . . . . 12
TV Control Panel 13 ....................
POWER Indicator .................... 13
Setting Up TV Inputs 14.....................
Basic TV Operation 16......................
Using the TV with a Personal Computer ....... 19
2 TV Connections
Before You Begin ....................... 21
Connection Types and Audio/Video Quality .... 21
Inputs and Outputs ...................... 22
Cable Routing ......................... 22
H
DMI Device .............................24
Y Pb Pr Component Video Device . . . . . . . . . . . 25
DVI Video Device ....................... 25
Antenna or Cable TV Service . . . . . . . . . . . . . . . 26
Composite Video Device .................. 26
VCR or DVD Recorder to an Antenna or
Wall Outlet Cable ...................... 26
A/V Receiver .......................... 27
A/V Receiver with HDMI Output . . . . . . . . . . . . . 27
Supplemental Audio Connections ......... 28
3 TV Features
Sleep Timer ........................... 29
FAV (Favorite Channels) ................... 29
ChannelView Channel Listings . . . . . . . . . . . . . . 30
Status Display ......................... 31
Using an External Sound System . . . . . . . . . . . . 32
Picture Shape and Display Formats .......... 33
Camera Images and Music Files . . . . . . . . . . . . 34
USB Source Devices .................. 34
Photos and Motion Video as
Composite Video ................... 36
Using an A Only Deviceudio- . . . . . . . . . . . . 36
Wireless Audio Playback . . . . . . . . . . . . . . . 37
Sound Projector ........................ 38
StreamTV™ Internet Media . . . . . . . . . . . . . . . . 42
Introduction to Home-Theater Control ........ 45
4 TV Menus
Main Menu ............................ 46
Picture............................... 46
Sound ............................... 49
Captions ............................. 51
Setup ............................... 52
Inputs ............................... 55
Lock ................................ 57
5 NetCommand IR Control
About Command IR ControlNet . . . . . . . . . . . . . 60
IR Emitters ............................ 61
NetCommand Setup ..................... 62
Operating NetCommand-Controlled Devices . . . 63
6 NetCommand IR Control of an A/V Receiver
Controlling an A/V Receiver after NetCommand
Setup .............................. 67
Setting Up V Receiver ControlA/
Power and Volume ................... 68
Automatic Audio/Video Switching Over
an HDMI Connection . . . . . . . . . . . . . . . . . 69
Appendices
Appendix A: Programming the Remote Control 73 .
Appendix B: Bypassing the Parental Lock ..... 79
Appendix C: HDMI Control of CEC Devices .... 81
Appendix D: TV Care .................... 84
Appendix E: Troubleshooting . . . . . . . . . . . . . . 85
Trademark and License Information .......... 92
Warranty .............................. 99
Network Service Disclaimer . . . . . . . . . . . . . . . 100
Index ................................ 101
4
For assistance call 1(800) 332-2119
Important Information About Your TV
Installation and Operating Notes
Custom cabinet installation must allow for proper
air circulation around the television.
NOTE TO CATV SYSTEM INSTALLER: THIS REMINDER
IS PROVIDED TO CALL THE CATV SYSTEM INSTALLER’S
ATTENTION TO ARTICLE 820-40 OF THE NEC THAT PRO-
VIDES GUIDELINES FOR THE PROPER GROUNDING AND,
IN PARTICULAR, SPECIFIES THAT THE CABLE GROUND
SHALL BE CONNECTED TO THE GROUNDING SYSTEM OF
THE BUILDING, AS CLOSE TO THE POINT OF CABLE ENTRY
AS PRACTICAL.
TV Software
Do not attempt to update the software of this TV with
software or USB drives not provided by or authorized
by Mitsubishi Digital Electronics America, Inc. Non-
authorized software may damage the TV and will not be
covered by the warranty.
For Your Records
Record the model number, serial number, and
purchase date of your TV. The model and serial
numbers are on the back of the TV. Refer to this
page when requesting assistance with the T V.
MODEL NUMBER
SERIAL NUMBER
PURCHASE DATE
RETAILER NAME
LOCATION
Children and TV Viewing
The American Academy of Pediatrics discourages
television viewing for children younger than two years of
age.
If Your TV Gets Damaged
Crystalline liquid may leak from the LCD panel and
broken glass may be scattered.
CAUTION: The crystalline liquid is toxic. Avoid
contact with your skin, eyes, or mouth. DO NOT
touch the broken glass or crystalline liquid. DO NOT
get glass fragments or crystalline liquid into eyes or
mouth. Should either contact your eyes or mouth,
rinse the contacted area thoroughly with water and
consult your doctor.
Disposal of Your TV
The LCD panel contains a small amount of crystalline
liquid which is toxic and should not be touched.
DO NOT dispose of the TV with general household
waste. For disposal or recycling information, contact
your local authorities or the Electronic Industries Alli-
ance at www.eiae.org.
5
For assistance call 1(800) 332-2119
Important Safety Instructions
Please read the following safeguards for your TV and
retain for future reference. Always follow all warnings
and instructions marked on the television.
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with dry cloth.
7) Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.
8) Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
9) Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10) Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
11) Only use attachments/accessories specified by the
manufacturer.
12) Use only with the cart,
stand, tripod, bracket,
or table specified
by the manufacturer,
or sold with the
apparatus. When
a cart is used, use
caution when moving
the cart/apparatus
combination to avoid
injury from tip-over.
13) Unplug this apparatus
during lightning storms or when unused for long
periods of time.
14) Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
ANT E NN A
LE AD IN WIR E
ANT E NN A
DIS C HA R GE UN IT
(NE C AR TIC L E 810-20)
G R OUN DING
C O NDUC T OR S
(NE C AR TIC L E 810-21)
G R OUN D C LAMP S
P OWE R S E R VIC E G R OUNDING
E LE C T R ODE S Y S TE M
(NE C AR T 250, P AR T H )
G R OUN D C LAMP
E LE C T R IC
S E R VIC E
E QUIP ME NT
NE C — N ATIO NAL E LE C T R IC AL C O DE
E XAMP LE O F ANT E NNA G R OUNDING
Outdoor Antenna Grounding
If an outside antenna or cable system is connected
to the TV, be sure the antenna or cable system is
grounded so as to provide some protection against
voltage surges and built-up static charges.
Replacement Parts
When replacement parts are required, be sure the
service technician has used replacement parts speci-
fied by the manufacturer or have the same character-
istics as the original part. Unauthorized substitutions
may result in fire, electric shock or other hazards.
6
For assistance call 1(800) 332-2119
Stand Installation
CAUTION
Using this TV with other than the authorized accessories may cause the TV to become unstable, which •
can cause damage to the product or possible injury.
At least TWO PEOPLE are required to install the stand. Support the TV near the corners as shown. Failure to follow •
these recommendations may result in personal injury and damage to the product.
Required: Phillips Screwdriver
1
Extension pieces
on k of standbac
2
3
TV
CAUTION.
Place the
stand in the foam insert
with the extension pieces
facing away from the TV.
Otherwise, the TV will be
damaged in transit.
Protect the TV and
stand with the original
packing material.
DON’T place your hand where it can
get caught under the TV.
DO support the TV
under the corners.
TV in protective
wrapping
Extension pieces on stand
must face out, away from TV.
Repacking the Stand
Two adults are required to lift the TV.
BACK
Note
40- or 46-inch TV:• If planning to wall-mount the TV, there is no need to install the stand.
55-inch TV: • The TV comes from the factory with the stand pre-installed.
7
For assistance call 1(800) 332-2119
Wall-Mounting
To order a wall-mount kit, please contact Peer-
less Industries, Inc. at (800) 473-3753 or visit
www.peerlessmounts.com. Order wall-mount kit model
ST650.
To order a wall-mount kit from Mitsubishi Digital Elec-
tronics America, Inc., please visit www.mitsuparts.com
or call (800) 553-7278.
Complete installation instructions are included with the kit.
Stand Removal Prior to Wall-Mounting
Disconnect the TV’s AC power cord from the AC
1.
power outlet.
Spread the protective sheet that was wrapped
2.
around the TV on a flat, even surface, such as a
sturdy table. The protective sheet will help prevent
damage to the display.
IMPORTANT: To avoid damaging the screen,
make sure there are no foreign objects under or
on top of the protective sheet.
Position one person on each side of the TV (left and
3.
right sides). Have each person firmly grasp their side
of the TV and gently place it face down on the pro-
tective sheet with the display stand hanging over the
edge of the table. See the illustration to the right.
Use a magnetic philips screwdriver to remove the
4.
stand screws from the recessed holes (see illustra-
tion to right). Note: A regular screwdriver can be
used with a separate magnetic pick-up tool.
While one person holds the TV with both hands,
5.
have the other person grasp the stand (see illustra-
tion to the right) and remove the stand by pulling it
away from the TV in the direction of the large arrow
shown in both illustrations.
5BCMF
1SPUF JWFDU
T FUIF
57 4UBOE
CAUTION
At least TWO PEOPLE are needed to safely remove the stand. Have one person hold the TV while the other person
removes the stand. Failure to follow these recommendations may result in personal injury and damage to the product.
Note
55-inch TV: • Remove the factory-installed stand prior to wall-mounting.
40- or 46-inch TV:• If you installed the stand for table-top use, follow these instructions to remove it prior
to wall-mounting the TV.
55-inch TVs
(6 screws)
40- and 46-inch TVs
(4 screws)
Protective
Sheet
Pull stand
to remove.
8
For assistance call 1(800) 332-2119
Special Features of Your TV
Your new high-definition widescreen television has
many special features that make it the perfect center of
your home entertainment system, including:
1080p High-Definition LCD Display System
Your Mitsubishi LED LCD HDTV uses a full 1920 x 1080
LCD panel to create the picture you see on the screen. All
images are displayed at 1080p. The TV uses new Plush
1080p® 5G digital video processing to convert lower-reso-
lution signals to 1080p for display.
True120Hz and True240Hz
True120Hz (154 and 164 series) and True240Hz (265 series)
make fast-moving images appear smoother and more fluid,
free from motion blur. It does this by doubling the tradi-
tional progressive scan frame rate and creates new frames
of video between the traditional frames to create smoother
moving images. True120Hz/True240Hz also smooth film
judder (image vibration) that may be present in film-based
content such as movies.
16:9 Widescreen Picture Format
Enjoy a full theatrical experience in the comfort of your
home. View pictures as film directors intended them.
Digital TV broadcasts, DVDs and newer video game
consoles support this widescreen format.
Integrated HDTV Tuner
Your widescreen Mitsubishi HDTV has an internal HDTV
tuner able to receive both over-the-air HDTV broad-
casts (received via an antenna) and non-scrambled
digital cable broadcasts, including non-scrambled
HDTV cable programming.
High-Definition Video Inputs
Component Video Inputs.• Also called Y/Pb/Pr
inputs, these inputs receive standard analog video
formats of 480i, 480p, 720p, and 1080i high-defini-
tion signals. This provides a high level of flexibility
when connecting DVD players/recorders, cable
boxes, and satellite receivers.
HDMI Inputs.• These inputs accept digital 480i,
480p, 720p, 1080i, and 1080p video signals plus
bitstream and PCM digital stereo signals. The
HDMI™ inputs can also accept a variety of PC
signals and resolutions.
Used with an adapter, these inputs also accept
compatible digital DVI video signals. HDMI
inputs provide additional high-performance,
high-definition connections for maximum flexibility
in your choice of home theater products. The HDMI
inputs are HDCP copy-protection compatible.
Easy Connect Auto Input Sensing
Easy Connect™ Auto Input Sensing automatically rec-
ognizes when you plug in a device and prompts you to
assign a name to it.
Home-Theater Control
HDMI Control
Available on all models. HDMI devices with Consumer
Electronics Control (CEC) capabilities may be compatible
with the TV’s HDMI Control feature. Compatible devices
can receive control signals through the HDMI connection,
allowing the TV’s remote control to operate some func-
tions of these devices.
NetCommand with IR Learning
265 Series. NetCommand® supports IR (infrared) control
of products such as VCRs, DVD players, cable boxes,
and satellite receivers. NetCommand can “learn” remote
control signals directly from many devices, allowing you
to create a customized NetCommand-controlled home-
theater system.
Sound Projector
Sound Projector technology uses the TV’s bank of
speakers to create a simulated surround sound effect
by reflecting sound off the room walls.
StreamTV™ Internet
StreamTV brings many popular internet applications to your
TV. Among them is the VUDU
™ movie service, offering the
largest on-demand HD movie selection anywhere, featur-
ing full 1080p and 5.1 surround sound. VUDU allows you
to enjoy movies with no store visits, no mailing, no late fees
and no subscriptions.
ENERGY STAR®
This is an ENERGY STAR
® qualified TV. Products that
earn the ENERGY STAR prevent greenhouse gas emis-
sions by meeting strict energy efficiency guidelines set
by the U.S. Environmental Protection Agency and the
U.S. Department of Energy.
This TV uses power within ENERGY STAR guidelines
except when Picture Mode is set to .Brilliant
10 1. Basic Setup and Operation
For assistance call 1(800) 332-2119
TV Tips
Turning the TV On or Off
Point the emitter (bulb) end of the remote •
control at the front of the TV and press the
POWER
button.
Press the •
POWER
button on the TV control
panel.
Controlling Sound Volume
Press •
VOL
to adjust the sound level.
See also • “Controlling A/V Receiver Sound
Volume” on page 32.
Before You Begin
Review the important safety, installation, and oper-
1.
ating information at the beginning of this book.
Choose a location for your TV.
2.
• See the stand-installation or wall-mounting
requirements starting on page 6.
• Allowatleastfourinchesofspaceonallsides
of the TV to help prevent overheating. Over-
heating may cause premature failure of the TV.
• Avoidlocationswherelightmayreflectoffthe
screen.
Install the batteries in the remote control.
3.
Plug the TV into an AC power outlet.
4.
TV power connection
Press the
1.
TV
key to
ensure that the remote
control is in
TV
mode.
TV
Aim the emitter end of the
2.
remote control at the TV
and press the
POWER
key
. Wait for the Welcome
screen.
If you wish to change the
3.
menu language to , Español
press .
Press
4.
to move to the
energy-mode selections.
Select .Home
Press
5.
to highlight EXIT.
Press
ENTER
to clear the
menu.
Welcome Screen Energy Options
Mitsubishi recommends the • Home setting,
which uses power within ENERGY STAR®
guidelines.
The • Retail setting looks best under bright
lighting. In this mode, the TV uses power in
excess of ENERGY STAR guidelines.
This table compares energy choices offered in the
Welcome screen.
Home Retail
Picture Mode Bright Brilliant
Backlight Level
Reduced
Brightness
Full Brightness
First-Time Power-On
1. Basic Setup and Operation 11
For assistance call 1(800) 332-2119
TV Controls
Remote Control
For more on use and care of the remote control, see
page 84.
Emitter (Bulb) End
Note: To operate other audio/video devices using the
TV’s remote control, use any of these methods:
• SeeAppendix A, “Programming the Remote
Control.”
• ForHDMIdevicescompatiblewiththeTV’sHDMI
Control feature, see Appendix C.
• 265 Series
See - page 60 for NetCommand IR “Learning” of
device keys.
For use of specific keys with NetCommand- -
controlled devices, see “Special Operation
Methods,” page 64.
(
PAUSE
)
Freezes a broadcast TV picture.
Record/Playback controls for external devices
When remote control is programmed, page 73
HDMI control, page 83
265 Series: With NetCommand, page 66
Powers TV on or off.
Number/letter keys
Channel tuning, page 16
Pass-code entry, page 57,
page 43
Sleep Timer, page 29
TV CAB/SAT DVD AUDIO VCR
P
ress the key for the device type to
control. Leave in TV mode for normal
TV viewing.
GUIDE
ChannelView listings, page 30
.
INFO
TV status
or TV help.
MUTE
Mutes the TV speakers.
TOOLS
Displays shortcuts for the number keys.
Press to check if shortcuts are available
for the current device. See the next
page.
VOL
Controls volume of TV speakers.
CH
PAGE
Changes channels; moves to another
page in a menu or list.
Adds a separator in digital channel
numbers. Clears some menu entries.
AUDIO
Audio settings, page 49
VIDEO
Video settings, page 46
MENU
Displays or clears the TV main
menu (page 46).
Also steps
back one menu.
EXIT
Clears all menus.
LAST
Returns to the previous channel;
moves back one menu
F1–F4.
265 Series. Special keys for
use with NetCommand IR control. See
“Initial NetCommand Setup”.
ENTER
Selects a channel number or menu item.
Navigation and adjustment
controls
FAV
Displays up to nine favorite
sources, page 29.
FORMAT
Changes picture shape,
page 18
INTERNET
Connects to StreamTV internet
content, page 42.
INPUT
Press to select a TV input,
page 16.
1. Basic Setup and Operation 13
For assistance call 1(800) 332-2119
TV Control Panel
Buttons on the control panel duplicate some keys on
the remote control.
To display the main menu, press •
INPUT
and
VOL+
simultaneously for about 10 seconds. Press and
hold
INPUT
and
VOL+
for 10 seconds to clear the
menu.
Refer to • left labels when no TV menus are dis-
played.
Refer to • right labels when using T V menus or after
activating a special function.
System Reset
If the TV fails to respond to the remote control, the
control-panel buttons, or will not power on/off, perform
System Reset. Recent setting changes made before
using System Reset may be lost.
To perform System Reset, press and hold the
POWER
button on the control panel for 10 seconds.
Panel-Lock Release
To • release the Panel Lock using the TV control
panel, press and hold the
INPUT
button on the
control panel for ten seconds. If the TV is off, press
the
POWER
button to make it power on.
To activate the Panel Lock, use the • Lock menu,
page 59.
TV control panel
TV Controls, continued
POWER
INPUT
ENTER
CH
VOL
POWER Indicator
POWER
Key
Off
Steady On
Slow Blinking
Fast Blinking
LED Color TV Condition
None TV is powered off. Normal operation.
Green TV is powered on. Normal operation.
Green
TV powered off, auto-on TV Timer is set.
Normal operation. TV can be turned on at any time.
Red/
Yellow
TV may require service.
Hold power button on front panel for 10 seconds to reset TV.•
If LED continues to flash red and yellow after reset, turn off the •
TV and unplug it from the AC power source. Wait one minute
and then plug the set back in.
If LED continues to flash red and yellow,•
go to
www.mitsubishi-tv.com or call 1-800-332-2119 to receive Autho-
rized Service Center information.
You may be asked to count how many times the LED flashes
each color to assist in troubleshooting.
14 1. Basic Setup and Operation
For assistance call 1(800) 332-2119
Setting Up Inputs with Auto Input Sensing
Power on the TV.
1.
Power on the devices to ensure detection.
2.
Connect one device to the TV, making note of the
3.
TV input jack.
The TV will display the screen if New Device Found
the connection type is detectable.
Highlight the device type in the on-screen list and
4.
press
ENTER
. The name you select here will appear
in the menu.Input Selection
Sample New Device
Found screen.
Important Note for NetCommand Users
265 Series. Be sure to select the correct device
type here. Although you can change the device type
later using the > menu, any “learned” Inputs Name
NetCommand IR codes will be erased when you
make the change.
Press
5.
EXIT
to close the screen.New Device Found
Repeat the preceding steps for each for each addi-
6.
tional device you want to add.
Using the ANT (Antenna) Input
If using an antenna or direct cable service (no cable
box), connect the incoming coaxial cable to the TV’s
ANT
input. Refer to page 26.
You must perform a channel scan to enable recep-
tion of digital channels. If you skip this step, the TV
will receive only analog channels. The channel scan
will search for high-definition and standard-definition
channels available in your area.
Memorizing Channels with Channel Scan
For the ANT input
To start channel memorization
Power on the TV.
1.
Press
2.
MENU
and open the menu.Setup > Channel
Start channel memorization from the Setup > Channel
menu.
Press
3.
to enter the menu.
Highlight
4.
Ant Air if connected to an
over-the-air antenna. Highlight Ant
Cable for service over direct cable
(no cable box). Press
ENTER
to add a
check.
Select the scan type.
5.
For first-time setup, highlight • All
channels.
To scan for channels not already •
in memory, highlight New only.
Press
ENTER
to add a check.
Highlight
6.
Scan and press
ENTER
.
Channel memorization may take up
to 15 minutes to complete.
To stop channel memorization before completion,
press
CANCEL
.
At any time after Channel Scan,
Use the • Setup > Channel > Edit menu (page 53) to
add or delete individual channels from memory.
Perform an additive scan with the • New only option
to add channels not already in memory.
Repeat the • All channels scan if you move the TV
to a new geographic area with a different channel
line-up or reposition the antenna.
Setting Up TV Inputs
1. Basic Setup and Operation 15
For assistance call 1(800) 332-2119
About Auto Input Sensing
This TV’s Easy Connect™ Auto Input Sensing feature
detects the following connections automatically:
Analog video jacks from inputs 1, 2, and 3•
HDMI inputs (when powered on)•
• USB device containing photo and music files
(JPG and MP3 formats).
Auto Input Sensing for Most Devices
When you first connect a device, the TV will:
a. Detect the connected device and automati-
cally switch to it.
b. Prompt you to identify the device type.
c. Repeat these steps for other newly detected
devices.
When You First Connect a Device
Most Device Types.• Select the device type from
the on-screen list. The device type you select here
will appear as an icon in the Input Selection menu.
A/V Receiver. •
For an HDMI-equipped A/V
receiver, select AVR
from the list of device types if
the A/V receiver is not recognized automatically.
HDMI CEC Devices Compatible with the •
TV’s HDMI Control Feature.
Compatible
CEC-enabled HDMI-equipped devices are often
recognized automatically by the TV.
HDMI Control
may allow you to control some functions of a CEC-
enabled device. See Appendix C, “HDMI Control
of CEC Devices.”
New Device Found screen for a device with HDMI
control enabled. Select On if you want to enable the
TV’s HDMI control of the device. In some cases, as
in the example above, you will also be prompted to
select a device name.
Tips on Auto Sensing
Choose a different name for each input.•
The antenna input (•
ANT
) is never detected,
although you can turn off the unused antenna
input in the > menu.Inputs Name
Change the device type displayed in the • Input
Selection Inputs > Namemenu by using the
menu (page 55).
Some HDMI devices can automatically tell the TV •
what name to use in the menu Input Selection
and you will be unable to change the name.
The TV is unable to detect a new connection if •
the current input is USB, Bluetooth®, or internet.
Switch to a different input before connecting.
265 series.• Any “learned” NetCommand IR
codes will be erased if you change the device
type in the menu.Inputs > Name
Reactivating Auto Input Sensing
for an MI InputHD
After you disconnect an HDMI device, Auto Input
Sensing is temporarily disabled. Perform these
steps:
Disconnect the HDMI device.
1.
Delete the removed HDMI device in the
2.
Inputs >
Name menu (see “Removing an HDMI Device,”
page 83).
Connect the new device and the
3.
New Device
Found screen will display.
Setting Up TV Inputs, continued
1. Basic Setup and Operation 17
For assistance call 1(800) 332-2119
Picture Settings
To get the best picture under different viewing con-
1.
ditions, set the Picture Mode first before changing
other video settings. See page 46.
a. Press
VIDEO.
b. Press until Picture Mode
displays.
c. Press to make one of these selections:
Name When to Use
Brilliant
Under bright light
Game
With gaming consoles (inputs
named
Game
or
PC
only)
Bright For most daytime viewing
Natural For most nighttime viewing
Press
2.
to display the name of another adjust-
ment.
Press
3.
to make the adjustment.
Press
4.
EXIT
to clear the display.
Additional picture options are available through these
menus:
Menu Name Page
Picture > Video 46
Picture > Picture Plus
47
Picture > Perfect
(265 Series)
48
Picture > Advanced (164 and 265 Series) 48
Basic Audio Controls
Controlling Sound Volume
Press •
VOL
to adjust the sound level
of the TV speakers.
Control •
subwoofer volume with an
on-screen slider
. See page 49. Set
Sound > Global > Subwoofer to
On to make this adjustment avail-
able.
See also • “Controlling A/V Receiver
Sound Volume” on page 32.
Changing Audio Settings (TV Speakers Only)
Press
1.
AUDIO
.
Press
2.
to find the adjust-
ment you want. See page 49.
Press
3.
to change.
Changing the Audio Output
To switch from the internal TV speakers to an external
sound system,
Press
1.
AUDIO
.
Press
2.
to display the option.TV Speakers
Press
3.
to change to Off.
Basic TV Operation, continued
TV Care
See page 84.
Assistance
For troubleshooting, service, and product support, •
see Appendix E, starting on page 85.
For warranty information, see • page 99.
18 1. Basic Setup and Operation
For assistance call 1(800) 332-2119
More TV Features
Feature
Page
Parental controls ( menu)Lock 57
Audio Lock (controls your sound system with
the TV’s remote control left in
TV
mode.)
74
TV Clock. Set the TV Clock if you plan to use
the TV Timer (page 52) or ChannelView (page
30).
52
Favorite channels or sources 29
ChannelView and custom channel collections 30
Changing the input names that appear in the
Input Selection menu (Inputs > Name menu)
55
Digital camera images and mp3 music files 34
164 and 265 Series. Listening to a wireless
audio device with the TV speakers
37
StreamTV™ internet access 42
Basic TV Operation, continued
The RMAT Key and Picture ShapeFO
Important
Black bars at the edges of
the screen are common in HD
pictures. Black bars are not a
defect of the TV.
Black bars are added by broad-•
casters to fill the 16:9 screen
area while preserving the original
aspect ratio of the picture.
Your cable box, satellite receiver, •
or other device may also be
altering the broadcast picture.
If your device offers output in
native format, try using it with
Mitsubishi picture formats.
Sample Uses of the
FORMAT
Key
You can use the
FORMAT
key to reduce or eliminate black areas at the
edges of the picture.
Press
Squarish 4:3 image is
narrower than the 16:9
screen; unused areas at the
sides are filled with black.
Wide Expand mode stretches
the picture sideways to fill the
screen.
Press
Wide 2.35:1 anamorphic DVD
image; unused areas at the
top and bottom are filled with
black (letterbox effect).
Zoom mode. The picture fills
the screen. All four edges are
cropped in this mode.
Repeatedly press the
FORMAT
key to cycle
through displays for the
current program. The
TV will remember the
format you last used on
each input.
For details, see page 33
Feature
Page
Programming the remote control to operate
other A/V devices
73
Controlling compatible devices using HDMI
CEC control
81
265 Series. Controlling A/V devices with Net-
Command
60
1. Basic Setup and Operation 19
For assistance call 1(800) 332-2119
Connecting a Computer to the TV
Use one of the connection methods listed below based
on your computer’s video output.
Computer
Video Output
Video Connection Audio
Connection
Digital DVI DVI-to-HDMI cable
or an HDMI cable
with a DVI-to-HDMI
adapter
Analog audio
cable with mini
plugs
HDMI HDMI-to-HDMI
cable
No additional
audio connec-
tion is required.
IMPORTANT
This TV accepts digital computer
video signals only. This TV is not
compatible with VGA (analog)
computer video.
VGA
PC MONITOR OUT
Connect the computer’s digital signal output to one
1.
of the TV’s HDMI jacks. See the connection dia-
grams for the method suited to your equipment.
Connect the computer’s audio output using one of
2.
these options:
• FordigitalDVIvideosignals,connectthe
analog audio output to the TV’s
DVI/PC AUDIO
INPUT
jack.
• ForHDMIsignals,noadditionalaudioconnec-
tion is required.
Note: If you are unable to hear audio from the
computer, there may be an incompatibility in
the computer’s hardware, software, or internal
settings. Consult a trained computer technician
for advice.
Power on the TV and computer. The TV will detect
3.
the connection and display the New Device Found
screen.
In the
4.
New Device Found screen, press to
highlight in the list of device types. It is impor-PC
tant to use the name so that the TV processes PC
the PC signal correctly.
Highlight
5.
EXIT and press
ENTER
to close the New
Device Found screen.
Note:
If your computer provides digital audio output
(coaxial or optical), you can connect it directly
to a digital A/V receiver and bypass the TV.
Using the TV with a Personal Computer
H
DMI Connection
Mitsubishi recommends using high-speed HDMI
cables to connect newer devices incorporating HDMI
technology.
Computer with
HDMI output
HDMI-to-HDMI
cable
TV
An HDMI-to-HDMI connection carries all video and
audio on a single cable.
HDMI and Digital Surround Sound
The TV’s HDMI inputs can receive digital surround
sound from an HDMI device. Use an HDMI connec-
tion if you want to hear digital surround sound from
the TV’s internal speaker array.
DVI Video Connection
DVI OUT
AUDIO
OUT
Computer
with Digital
DVI output
DVI-to-HDMI
cable
Audio cable
TV
A DVI connection from a personal computer requires a
separate audio connection.
20 1. Basic Setup and Operation
For assistance call 1(800) 332-2119
Tip
Set the computer’s screen saver to display a pattern
after several minutes of inactivity. This acts as a
reminder that the TV is powered on.
Computer Video Adjustments
Power on the computer.
1.
Select
2.
PC from the menu. To do Input Selection
this, press
INPUT
to open the menu, Input Selection
move the highlight to the PC icon, and press
ENTER.
Working from the computer, change
3.
the resolution of the computer image.
View the computer image on the TV
and maximize the computer resolution
while maintaining a suitable aspect
ratio for the image.
Perform TV video adjustments.
4.
Press
VIDEO
repeatedly to access video-
adjustment options.
Press
5.
FORMAT
repeatedly to find the
picture shape best suited to the
image. See the chart on this page
showing how different computer reso-
lutions can be displayed on the TV.
Image Resolution
Your Mitsubishi TV can display the resolu-
tions shown in the chart from standard
VGA (640 x 480) through 1920 x 1080
signals at a refresh rate of 60 Hz.
In most cases, the computer will select
the best resolution match to display on
the TV. You can override this setting if you
wish. Refer to your computer operating
system’s instructions for information on
changing the screen resolution.
You may need to restart the computer for
changes to take effect.
Using the TV with a Personal Computer
Distortion in Computer Images
Computer images may show distortion
when viewed on the TV, e.g., lines that
should be straight may appear slightly
curved.
Computer Display Formats
Press
FORMAT
repeatedly to cycle through the TV displays available
for your computer’s video signal.
Computer Signal
As Displayed on TV Screen
Original Format 4 X 3
Standard
16 X 9
Standard Zoom
VGA
640 X 480
SVGA
800 X 600
Original Format Standard Zoom
XGA
1024 X 768
PC 720p
1280 X 720
WXGA
1360 X 768
SXGA
1280 X 1024
Original Format Standard
PC 1080p
1920 X 1080
21
For assistance call 1(800) 332-2119
2TV Connections
Auto Input Sensing
The TV’s Auto Input Sensing feature automatically rec-
ognizes many connections and prompts you to identify
the type of device connected. See page 15 for more on
Auto Input Sensing.
Connection Types
Use the connection types available on your input
devices that will give the best video quality. For
example, choose HDMI over component video; choose
component video over composite video.
Picture Quality
For best picture quality, route signals directly from the
source device to the TV whenever possible.
Surround Sound
To use the surround sound capabilities of the TV’s •
speaker array, you must connect the digital sur-
round sound source to the TV on either
An HDMI input -
The -
ANT
antenna input
For best surround sound audio quality from an •
external sound system, route audio-carrying cables
from the source device directly to your sound
system.
IMPORTANT
Accessory items such as cables, adapters,
splitters, or combiners required for TV
connections are not supplied with the TV. These
items are available at most electronics stores.
Before You Begin
Connection Types and Audio/Video Quality
Component
GOODBEST GOODBEST
VIDEO QUALITY AUDIO QUALITY
HDMI-to-DVIHDMI Video Video
Composite L/R Analog
AudioAudio
Digital
HDMI
Stereo
Mini-Plug
22 2. TV Connections
For assistance call 1(800) 332-2119
Inputs and Outputs
12
13
DIGITAL
AUDIO
OUTPUT
(page 27)
USB
(page 35)
DVI/PC AUDIO
INPUT
(page 25)
CENTER-CH
INPUT
(page 28)
SUBWOOFER
OUTPUT
(page 28)
Calibration Micro-
phone Input
(265 series, page 40)
HDMI
(page 24)
HDMI
(page 24)
AVR/SURROUND
OUTPUT
(page 27, page 41)
NetC OUT/IR IN
(265 Series) NetCommand/
IR external controller jack.
See page 61)
Y/VIDEO
composite video
(page 26)
Y/VIDEO
com-
posite video input
(page 26)
Y/VIDEO Pb Pr
component
video input
(page 25)
Y/VIDEO Pb Pr
component video
input (page 25)
ANT
coaxial antenna
input
(page 26)
AUDIO
analog stereo
audio input
AUDIO
analog stereo
audio input
USB (Power Only)
Provides power to
TV accessories.
(page 28)
LAN
(Ethernet, port
page 42)
1
5
3
4
8
9
3
4
5
6
7
2
11
14
10
2
Cable Routing
1
2
Install the supplied
cable ties in any of four
mounting holes.
Installing the cable
tie
Removing the
cable tie
Sample cable routing. Secure the cable
bundle with the release tab facing out.
Press the release tab to
loosen the cable bundle.
2. TV Connections 23
For assistance call 1(800) 332-2119
Inputs and Outputs, continued
1. ANT (Antenna)
Connect your main antenna or direct cable service
(without a cable box) to
ANT
. The
ANT
input can
receive digital and analog over-the-air channels from
a VHF/UHF antenna or non-scrambled digital/analog
cable source.
2. HDMI ® Inputs
(High-Definition
Multimedia Interface)
The HDMI inputs support uncompressed standard and
high-definition digital video formats, bitstream Dolby
Digital 5.1, and PCM digital stereo audio.
Mitsubishi recommends you use high-speed HDMI
cables to connect newer source devices incorporating
HDMI technology. High-speed cables bring you the full
benefits of Deep Color and x.v.Color.
These HDMI inputs can also accept digital DVI video
signals. To connect a device’s DVI output to the TV’s
HDMI input, use an HDMI-to-DVI adapter or cable plus
an analog audio. Connect the audio cable to the
DVI/PC
AUDIO INPUT
jack on the TV to receive audio from your
DVI device.
Use the HDMI inputs to connect to CEA-861 HDMI com-
pliant devices such as a high-definition receiver or DVD
player. These inputs support 480i, 480p, 720p, 1080i,
and 1080p video formats.
The TV’s HDMI inputs are compatible with many DVI-D
and HDMI computer video signals.
These inputs are HDCP (High-Bandwidth Digital Copy
Protection) compliant.
3. Y/
VIDEO
(Composite Video)
Use the adjacent
AUDIO R
and
L
inputs if you wish to
send audio to the TV.
4. Y/VIDEO Pb Pr (Component Video)
Use the adjacent
AUDIO R
and
L
jacks if you wish to
send audio to the TV.
5. AUDIO
Analog stereo inputs for use in conjunction with adja-
cent composite or component video jacks.
6. NetC Out/IR IN
265 Series
As an output: Connect IR emitters to this jack to send
NetCommand control signals to external IR-controlled
devices.
As an input: Accepts control signals from an external
controller when set up by your professional installer.
7. LAN
Use the
LAN
Ethernet jack for streaming internet video
to the TV. See page 42 for setup. Visit www.VUDU.com
for details about VUDU ™ service.
8. USB
The TV can read JPEG photo files and mp3 music files
from a USB storage device connected to this input.
154 Series. Connect a compatible wireless adapter to
stream internet content to the TV
(page 42)
.
9. USB (Power Only)
Standard USB 5-volt, 500-milliamp power output you
can use to supply power to an accessory device, such
as a wireless subwoofer (page 28).
10. DVI/PC INPUT AUDIO
Connect a DVI device to one of the TV’s HDMI inputs
and use this jack to send analog audio to the TV.
11. DIGITAL AUDIO OUTPUT
This output sends Dolby Digital or PCM digital audio to
your digital A/V surround sound receiver. Incoming analog
audio is converted by the TV to PCM digital audio. If you
have a digital A/V receiver, in most cases this is the only
audio connection needed between the TV and your A/V
receiver.
HDMI Cable Categories
HDMI cables are available as Standard and
High-Speed types.
High-Speed HDMI Cables.• Newer DVD
players, video games, and set-top boxes require
High-Speed HDMI cables, suitable for clock
frequencies up to 340 MHz or data rates of up
to 10.2 gigabits per second. Use high-speed
cables for 1080p HD signals carrying extended
color encodings (i.e., 30 or more bits, also called
Deep Color). High-Speed HDMI cables are also
suitable for standard HDTV signals.
Standard HDMI Cables• . Standard HDMI
cables may be unmarked. They are suitable for
standard HDTV 720p, 1080i, and 1080p signals
with 8-bit color depth. Use Standard HDMI
cables for clock frequencies up to 74.25 MHz or
data rates of up to 2.23 gigabits per second.
24 2. TV Connections
For assistance call 1(800) 332-2119
Inputs and Outputs, continued
12. AVR/SURROUND OUTPUT
Sends analog audio of the current program to an •
analog A/V surround sound receiver or stereo
system. Digital audio from digital channels and
HDMI devices is converted to analog audio by the
TV for output on this jack. This is the only audio
connection needed to the TV if using an analog A/V
receiver or stereo system.
Note: If connecting headphones, set Sound >
Global > Analog Audio Out to Variable.
For a fuller surround sound effect, connect exter-•
nal rear speakers to this output to supplement the
TV’s speaker array. Set Sound > Global > Analog
Audio Out to Rear.
13. SUBWOOFER OUTPUT
Connect a powered subwoofer to this input to comple-
ment effects from the TV’s speaker array. Set Sound >
Global > Subwoofer to On to enable this output.
14. CENTER CH INPUT
Connect your A/V receiver’s center channel output to
this input to make the TV speakers output center-chan-
nel sound. Set Sound > Global > Center Channel
to On to enable this input. See Sound > Audio > TV
Speakers > Center page 49.
H
DMI Device
Commonly used with an HDTV Cable Box,
Satellite Receiver, or DVD/Blu-ray Player
Required: HDMI-to-HDMI cable.
Connect an HDMI cable from the TV to the device’s
HDMI output. HDMI-connectable devices provide
video and audio through a single cable.
Mitsubishi recommends using high-speed HDMI cables
to connect newer devices incorporating HDMI technol-
ogy. See “HDMI Cable Categories” on the previous
page for more on HDMI cable types.
Note: The HDMI connection supports copy protection
(HDCP).
Any HDMI device
HDMI-to-HDMI
cable
TV
IMPORTANT
HDMI and Digital Surround Sound
Use an HDMI connection if you want to hear digital
surround sound from the TV’s internal speaker array.
The TV’s HDMI inputs can receive digital surround
sound from an HDMI device.
Auto Input Sensing
The TV’s Auto Input Sensing feature automatically recog-
nizes some connections and prompts
you to identify the
device type. See page 15.
2. TV Connections 25
For assistance call 1(800) 332-2119
Y Pb Pr Component Video Device
Commonly used with an HDTV Cable Box,
Satellite Receiver, or DVD/Blu-ray Player
If your source device has an HDMI output, use the con-
nections for HDMI devices described on the opposite
page instead of component video.
Required:
RCA-type component video cables
Left/right analog audio cables.
Note:
To hear digital surround sound from an A/V receiv-
er, connect the digital audio output from the device
directly to your digital A/V receiver.
Pb
Y
Pr
AUDIO
L
R
Incoming from
cable service or
satellite dish
Component
video device
TV
Audio
cables
Component
video cables
CABLE IN or
SATELLITE IN
DVI Video Device
Commonly used with a Cable Box, Satellite
Receiver, or DVD Player
Connect a DVI device (digital only) to one of the TV’s
HDMI input jacks.
Required:
Analog stereo audio cables
DVI-to-HDMI cable or DVI/HDMI adapter and HDMI
cable
If you are using a DVI/HDMI adapter, it is important to
connect the adapter to the DVI device for best perfor-
mance.
Some devices require connection to an analog input
first in order to view on-screen menus and to select DVI
as the ouput. Please review your equipment instruc-
tions for DVI connectivity and compatibility.
Note: The HDMI connection supports copy protection
(HDCP).
DVI OUT
AUDIO
OUT
Digital DVI
device
DVI-to-HDMI
cable
Audio cable
TV

Produkt Specifikationer

Mærke: Mitsubishi
Kategori: TV
Model: Diamond LT-55265

Har du brug for hjælp?

Hvis du har brug for hjælp til Mitsubishi Diamond LT-55265 stil et spørgsmål nedenfor, og andre brugere vil svare dig


TV Mitsubishi Manualer

Mitsubishi

Mitsubishi LT-2220 Manual

21 Maj 2024
Mitsubishi

Mitsubishi WD-Y65 Manual

18 Maj 2024
Mitsubishi

Mitsubishi WD-65838 Manual

15 Maj 2024
Mitsubishi

Mitsubishi WD-62827 Manual

21 April 2024
Mitsubishi

Mitsubishi Diamond LT-55265 Manual

17 April 2024
Mitsubishi

Mitsubishi WS-65615A Manual

15 Marts 2024
Mitsubishi

Mitsubishi VS-60609 Manual

18 Februar 2024
Mitsubishi

Mitsubishi WT55315 Manual

17 Januar 2024
Mitsubishi

Mitsubishi WS-55315 Manual

9 Januar 2024
Mitsubishi

Mitsubishi WD-73742 Manual

3 Januar 2024

TV Manualer

Nyeste TV Manualer

Panasonic

Panasonic TX-24DS500B Manual

8 April 2025
Panasonic

Panasonic TV-50W93AE6 Manual

8 April 2025
Panasonic

Panasonic TV-43W80AEY Manual

8 April 2025
Panasonic

Panasonic TX-20LA1Z Manual

8 April 2025
Panasonic

Panasonic TX-32FS352B Manual

8 April 2025
Panasonic

Panasonic TX-L32C2BA Manual

8 April 2025
Panasonic

Panasonic TX-50A300B Manual

8 April 2025
Panasonic

Panasonic TX-37LX85L Manual

8 April 2025
Panasonic

Panasonic TX-LF37G10 Manual

8 April 2025
Grundig

Grundig Hamburg 32 GIH 5500 Manual

6 April 2025