Moxa OnCell G3150-HSDPA-JPS Manual

Moxa Ikke kategoriseret OnCell G3150-HSDPA-JPS

Læs gratis den danske manual til Moxa OnCell G3150-HSDPA-JPS (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 19 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 10 anmeldelser. Har du et spørgsmål om Moxa OnCell G3150-HSDPA-JPS, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/4
— 1 — — 2 — — 3 —
OnCell G3100 Series
Quick Installation Guide
Second Edition, September 2008
1. Overview
There are currently four models in the OnCell G3100 series of
IP-modems: the OnCell G3110, OnCell G3150, OnCell G3110-HSDPA,
and OnCell G3150-HSDPA. The main difference between the models is
the serial interface type. The OnCell G3100 industrial RS-232,
RS-232/422/485 GSM/GPRS/EDGE, or UMTS/HSDPA IP modems are
some of the most affordable, secure, and versatile products available in
the cellular networking market today. These modems also provide remote
access and TCP/IP support, and can be configured over a network.
2. Package Checklist
Before Installing the OnCell G3100 IP modem, verify that the package
contains the following items:
Standard Accessories
y Document & Software CD
y Omni 1 dBi rubber SMA antenna (OnCell G3100 model name:
ANT-CQB-O-1; OnCell G3100-HSDPA model name:
ANT-WCDMA-O-1.5 BK)
y Din-Rail Kit
y 5-pin terminal block (screw type)
y 10-pin terminal block (screw type)
y Product warranty statement
y Quick Installation Guide
Optional Accessories
y Power Adaptor: 1.2 A (or above) @ 12V
y DC power supply
y Power jack to terminal block cable
y Quad-band GSM/GPRS/EDGE antennas for OnCell G3110/G3150
series (impedance = 50 ohms):
ANT-CQB-O-0-3m: Omni 0dBi/10cm, magnetic SMA antenna, 3 m
ANT-CQB-O-3-3m: Omni 3dBi/25cm, magnetic SMA antenna, 3 m
ANT-CQB-O-5-3m: Omni 5dBi/37cm, magnetic SMA antenna, 3 m
Note: Please notify your sales representative if any of the above items are
missing or damaged.
3. Hardware Introduction
Front View Rear View
OnCell G3110/G3150 OnCell G3110-HSDPA/
G3150-HSDPA
SIGNAL
PWR 2
FAULT
GPRS
PWR 1
READY
GSM
Tx Rx
Ethernet
SMA Bulkhead Jack
SIGNAL
PWR 2
FAULT
GPRS
PWR 1
READY
GSM
Tx
UMTS
Rx
HSDPA
Ethernet
SMA Bulkhead Jack
DIN-rail Support
Matel Springs
Top View
PWR 2/PWR 1DI 2/DI 1 Relay
RESET
Bottom Views
OnCell G3110/G3110-HSDPA OnCell G3150/G3150-HSDPA
RS-232
RS-232 RS-422/485
Side Views
SIM card Cover
Left Side Right Side
Reset Button—Press the Rest button continuously for 5 sec to load
factory defaults: Use a pointed object, such as a straightened paper clip or
toothpick, to press the reset button. This will cause the Ready LED to
blink on and off. The factory defaults will be loaded once the Ready LED
stops blinking (after about 5 seconds). At this point, you should release
the reset button (the default IP is 192.168.127.254).
LED Indicators
The LED indicators on the front panel of the OnCell G3100 are described
in the following table.
LED
Name
LED
Color LED Function
Green DC Power is active
Power Off Power is off, or power error condition exists.
Green Serial Tx
Amber Serial Rx
Data
Off Ethernet cable is disconnected.
Amber GSM is connected.
GSM Off GSM is disconnected.
Amber GPRS is connected.
GRPS Off GPRS is disconnected.
Amber UMTS is connected.
(OnCell G3100-HSDPA only)
UMTS
Off UMTS is disconnected.
(OnCell G3100-HSDPA only)
Amber HSDPA is connected.
(OnCell G3100-HSDPA only)
HSDPA
off HSDPA is disconnected.
(OnCell G3100-HSDPA only)
Green Steady on: Software Ready.
Blinking slowly (1 sec): The OnCell has been
located by the OnCell Search Utility.
Ready
Off Power is off, or is booting up.
Red Steady on: Booting up, or IP fault.
Blinking slowly (1 sec): Cannot get an IP address
from the DHCP server
Fault
Off Power is off, or there is no error condition.
Signal
(3 LEDs) Green
Number of lit LEDs indicates signal level
(at least 2 LEDs must illuminated for data
transmission)
Digital Input and Output
Six terminals on the terminal block are reserved for the I/O ports, with 2
terminals used for each input, and 2 terminals used for each output.
Digital Input—Digital ON and OFF determine which power input is used:
DIN OFF: 0 to 3.3 VDC
DIN ON: 10 to 48 VDC (DI COM to DI)
Digital Output—The default for the relay output (DOUT) is open,
indicating a normal condition. If the relay output (DOUT) is shorted, it
indicates an exception.
P/N: 1802031000011

Produkt Specifikationer

Mærke: Moxa
Kategori: Ikke kategoriseret
Model: OnCell G3150-HSDPA-JPS

Har du brug for hjælp?

Hvis du har brug for hjælp til Moxa OnCell G3150-HSDPA-JPS stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Moxa Manualer

Moxa

Moxa UPort 1450I Manual

31 Marts 2025
Moxa

Moxa OnCell 5104-HSDPA Manual

11 Januar 2025
Moxa

Moxa OnCell G3150 Manual

23 August 2024
Moxa

Moxa ICF-1150I-M-ST Manual

23 August 2024
Moxa

Moxa M-3411 Manual

23 August 2024
Moxa

Moxa M-1600 Manual

23 August 2024
Moxa

Moxa TCC-82-RP Manual

23 August 2024
Moxa

Moxa MGate MB3270-T Manual

23 August 2024
Moxa

Moxa UPort 1410 Manual

23 August 2024
Moxa

Moxa M-1450 Manual

23 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Philips

Philips TD5101X Manual

15 August 2025
Philips

Philips AWP1721 Manual

15 August 2025
Candy

Candy CWVB6B Manual

15 August 2025
Philips

Philips ED8DVDRW Manual

15 August 2025
Sauermann

Sauermann Si-60 Manual

15 August 2025
Philips

Philips ES8DVDRX Manual

15 August 2025
Philips

Philips TD5101I Manual

15 August 2025
Philips

Philips GoSure TE60x Manual

15 August 2025
Adj

Adj FS600LED Manual

15 August 2025
Philips

Philips GoSure TE50i Manual

15 August 2025