Netgear FA311 Manual

Netgear Netværkskort/adapter FA311

Læs gratis den danske manual til Netgear FA311 (2 sider) i kategorien Netværkskort/adapter. Denne vejledning er vurderet som hjælpsom af 18 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 9.5 anmeldelser. Har du et spørgsmål om Netgear FA311, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

5. Fasten the card to the rear of the computer chassis by tightening the screw that is on the PC.

6. Replace the PC cover and reconnect the power cord to the PC.

Connect the Network Cables

Using the appropriate cable, connect the port on a network hub or switch to the port on the card. The port

on the card performs autonegotiation and supports full-duplex operation.

This section explains how to install the Network Driver in various Microsoft Windows Operating Systems.

Some versions of Microsoft Windows Operating System may respond with different dialog boxes, or the

dialog boxes may open in a different sequence than those shown in this guide, but should prompt you for the

same information.

Before you proceed with the installation steps, decide on a name for your network and for each PC. The

whole network must have the same workgroup name while each PC must have a unique name. These names

can be entered by going to Start>Settings>Control Panel>Network and clicking on the Identification tab.

You also need to have the Microsoft Windows Operating System CD-ROM and the GearBox for Adapters

CD ready to use in the installation process.

The installation screen uses FA311 as example.

Install the Windows XP Network Driver

Note: If the “Insert Disk” window opens and a message prompts you to insert your Windows CD-ROM at

any time during the installation process, insert the Windows CD-ROM in Drive D (the CD-ROM drive) and

click on “OK”. Then follow the next step in the instructions.

For FA311 and FA312 Adapters:

1. After installing the FA311 (or FA312) PCI Adapter, the Win XP will install the driver automatically.

2. You can go directly to section 4. “Test Your Network Connection”. Following the steps to check if the

driver is well installed.

For FA331 Adapters:

1. Turn on the power to the computer and start Windows XP.

2. Double-click “My Computer” on the desktop, double-click “Control panel” and then double-click

“System”.

3. Click “Hardware” and click “Device Manager” tab, then double-click “Network adapters”.

Installation Guide

Eve rybody ’s connecti ng.™

32bit

10/100 Mbps Fast Ethernet FA311/FA312/FA331

PCI Adapter

NETGEAR, Inc.

Support Information

Phone: 1-888-NETGEAR

E-mail: support@NETGEAR.com

www.NETGEAR.com

See Support Information Card for for additional phone numbers.

Internet / World Wide Web

Go to http://www.NETGEAR.com for the NETGEAR Web page.

Defective or damaged merchandise can be returned to your point-of-sale representative.

IMPORTANT!

Please register online. YOU MUST REGISTER TO OBTAIN TECHNICAL SUPPORT. PLEASE RETAIN

PROOF OF PURCHASE and this warranty information. To register your product, get product support, or to

obtain product information and NETGEAR product documentation, direct your Web browser to the

http://www.NETGEAR.com Web page.

July 2002

M - F A 3 0 0 N A - 3

Instructions in this guide are for users of Microsoft Windows Operating Systems.

As a last step, be sure to register your Adapter at http://www.NETGEAR.com.

Plan Your Time

Estimated setup time for this product is only minutes.

Unpack the contents of the package and make sure that you have everything.

• FA311 (or FA312, FA331) Fast Ethernet PCI Adapter

• GearBox for Adapters CD

• FA311/FA312/FA331 Installation Guide

Install the Card

Note: Touch a grounded metal object to free yourself of static electricity before you handle the card.

1. Turn the power off and unplug the power cord from your computer.

2. Remove the PC cover.

3. Choose an available PCI slot and remove the corresponding back plate from the PC chassis.

4. Insert the card into the PCI expansion slot.

Caution: To avoid damaging any components on the card, handle it by the edges, using your thumbs

to push it securely into the PCI slot. Make sure the card is fully inserted into the slot to prevent the PC

operating system from freezing at startup.

1 VERIFY PACKAGE CONTENTS

Model FA311 (or FA312, FA331)

Network Card GearBox for Adapters CD

3-pin LAN wake cable

(provided with Model FA312) Installation Guide

2 CONNECT NETGEAR TO YOUR ENVIRONMENT

Network card

Back plate

removed

PC with network

card installed Power adapter

PC with network

card installed

Printer

(optional)

Hub

RJ-45

Connector

Category 5 10/100 Mbps

UTP cables*

RJ-45

Connector

Use the cables provided or any Category 5 UTP cable.

Maximum length = 100 meters (300 feet)

4. Double-click “National Semiconductor DP83815-Based PCI Fast Ethernet adapeter”.

5. Click “Driver” and click “Update Driver” tab, then click “OK”.

6. A Hardware Update Wizard will appear. Insert the GearBox for Adapters CD (or disk) into your

CD-ROM drive. Select “Install from a list or specific location ( Advanced )”. Click “Next”.

7. When the following dialog box opens, select “Don’t search. I will choose the driver to install.”, then

click “Next”.

8. When Select Network Adapter box opens, click “Have Disk” then click “Next”.

1. Open the box

and verify its

contents

2. Connect NETGEAR to

your environment

3. Install Network Driver

4. Test Your Network Connection

5. Enjoy being connected!

START HERE

0:10

3 INSTALL NETWORK DRIVER

9. The Install From Disk box will open. Type “D:\” and click “OK”.

10. “NETGEAR FA330/FA331 PCI Adapter” will appear in the model list. Click “Next”.

11. The next Windows appears with the following adapter name : NETGEAR FA330/FA331 PCI Adapter.

Click “Finish”.

12. Remove the GearBox for Adapters CD (or disk) from the CD-ROM drive.

The Model FA311/FA312/FA331 Adapter driver installation for Windows XP is now complete.

Install the Windows 2000 Network Driver

Note: If the “Insert Disk” window opens and a message prompts you to insert your Windows CD-ROM at

any time during the installation process, insert the Windows CD-ROM in Drive D (the CD-ROM drive) and

click on “OK”. Then follow the next step in the instructions.

1. A Found New Hardware Wizard dialog box will appear, indicating that Windows 2000 has found the

adapter. Insert the GearBox for Adapters CD (or disk) into your CD-ROM drive (or disk drive).

2. Click “Next”.

Produkt Specifikationer

Mærke:	Netgear
Kategori:	Netværkskort/adapter
Model:	FA311

Har du brug for hjælp?

Hvis du har brug for hjælp til Netgear FA311 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Netværkskort/adapter Netgear Manualer

Netgear GS748PP Manual

28 September 2025

Netgear GSM4210PD Manual

23 August 2025

Netgear GS305EP Manual

14 Juli 2025

Netgear GS305PP Manual

7 Juli 2025

Netgear GS305EPP Manual

20 Februar 2025

Netgear RangeMax 240 Manual

2 August 2024

Netgear FA312 Manual

26 Juli 2024

Netgear FA120 Manual

25 Juli 2024

Netgear GA311 Manual

24 Juli 2024

Netgear WNDA4100 Manual

23 Juli 2024

Netværkskort/adapter Manualer

Nyeste Netværkskort/adapter Manualer

Lindy 43340 Manual

18 December 2025

Planet ENW-2QSFP28 Manual

17 December 2025

Simply45 S45-2012U Manual

7 December 2025

Approx APPUSB900 Manual

29 November 2025

D-Link DWA-548 Manual

29 November 2025

EXSYS EX-62026POE Manual

28 November 2025

Digitus DA-70852 Manual

28 November 2025

Atlantis Land NetPower 502 AV Manual

28 November 2025

EXSYS EX-62010POE-SFP Manual

28 November 2025

D-Link DWA-140 Manual

27 November 2025