Nexxt NCR-N301 Manual

Nexxt Router NCR-N301

Læs gratis den danske manual til Nexxt NCR-N301 (2 sider) i kategorien Router. Denne vejledning er vurderet som hjælpsom af 73 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 37 anmeldelser. Har du et spørgsmål om Nexxt NCR-N301, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

B.Ethernet Access

Modem

Internet

Internet Ethernet Cable

A.Telephone Line/FTTH

(Fiber To The Home)/

Cable Access

The default WiFi name is

Nexxt XXXXXX

There is no default WiFi password.

*Images herein are for references only. The actual product may differ.

Ethernet Cable

Quick installation guide

1 2 3

Preliminary steps

Product layout

This advanced network device works as a router,

wireless AP, WISP client and universal repeater.

Before setting up the router, you must verify that

you have high-speed internet access available. The

most widely used connection nowadays is broad-

band DSL or cable. The description used in this

guide is based on that type of connection.

1. Power off your PC, modem and the router.

2. Find the optimum location for the router. The best place is

usually at the center of your wireless network with the

antennas in the upright position.

3. Connect one end of the supplied power adapter to the AC

input jack located on the rear panel of the router, before

plugging the other end to a standard electrical wall outlet.

4. Connect your network devices to the LAN ports of the router.

Then using an ethernet cable, connect your modem to the

WAN port in order to gain internet access.

5. Finally, power on the router, your PC and modem.

Thank you for purchasing the new Nebula 301+

wireless-N router from Nexxt Solutions

®. If any of

the following items are mismatched, missing or

damaged, please contact the merchant from

whom you purchased the unit for immediate

replacement.

• Wireless-N router

• 100/240V power adapter

• Network cable

• Quick setup guide

1. Antennas: Four high-gain 5dBi omnidirectional

antennas.

2. WAN port: This RJ45 port is where you will connect the

fiber/cable/DSL modem, or ethernet line from your ISP.

3. LAN ports (1/2/3): Connect 10/100Mbps ethernet

devices such as computers, switches, and hubs to any of

these RJ45 ports.

4. Wi-Fi button: Push it for 1 to 3 seconds to enable or

disable the wireless network of the router.

5. WPS/Reset:

・Press this button for about one second to enable WPS

encryption. Within two seconds, enable the WPS feature

on the client device to establish a connection.

・Press this button for about eight seconds to restore

the device to its factory default settings. The LED

indicator will blink quickly.

6. Power: Connect the supplied power adapter to this jack.

10 11

Router configuration

1.Log into the router by accessing the web base

utility. To do so, in the browser’s address field enter

the default address or http://192.168.0.1

http://www.nexxtwifi.local

Note: To access the router wirelessly, look for the

SSID, (whereby represents the Nexxt_XXXXXX X

last 6 numbers of the MAC address).

2. In this stage, the wireless router web interface will

come up. The system will then prompt you to enter the

default password. Type and click to admin Login

continue.

3. Next, the Basic settings page will be displayed. In this

window, you will be prompted to select the Internet

Connection Type, which will depend on the type of

connection offered by your existing Internet Service

Provider (ISP): PPPoE, for dial-up or DHCP for other

broadband connections. You can also set it up to use

a Static IP configuration. By default, the router will

auto-detect the connection type and set it to the

corresponding configuration. You can also setup the

wireless password and SSID under the Wireless

Settings blank area (by default, this is ). For security

purposes, we recommend using a security key at this

stage. It must contain at least 8 characters. Click

to complete the initial set up of the router. OK

Front panel

Hardware installation

4. Once complete, you will get a successful setup

message. If the SSID and password were changed in

the previous step, you will need to access the router

using the newly assigned parameters.

Back panel

The rear panel provides the physical connectors for power

and the client network devices.

2 3 4 5

The LED indicator on the front panel provides information

about network activity, the connection and link status of

the ports in real time. They also facilitate activity monito-

ring and troubleshooting the performance of the device.

LED

indicator

Solid The router is starting up or is already

successfully connected to the internet

Blinks slowly The router fails to connect to the internet

Blinks quickly When clients are either connected or

disconnected to any of the LAN ports, the

LED will blink quickly for 3 seconds before

changing to solid

Description

WAN

Quick installation guide

16 17

This device complies with Part 15 of the FCC Rules.

Operation is subject to the following two conditions: (1)

This device may not cause harmful interference, and (2)

this device must accept any interference received,

including interference that may cause undesired opera-

tion.

This equipment has been tested and found to comply with

the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules. These limits are designed to provide

reasonable protection against harmful interference in a

residential installation. This equipment generates, uses

and can radiate radio frequency energy and, if not

installed and used in accordance with the instructions,

may cause harmful interference to radio communications.

However, there is no guarantee that interference will not

occur in a particular installation. If this equipment does

cause harmful interference to radio or television recep-

tion, which can be determined by turning the equipment

off and on, the user is encouraged to try to correct the

interference by one of the following:

FCC statement

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and

receiver.

Connect the equipment into an outlet on a circuit

different from that to which the receiver is connected.

Consult the dealer or an experienced radio/TV

technician for help.

•

Any changes or modifications not expressly approved by

the party responsible for compliance could void the user's

authority to operate the equipment.

This transmitter must not be co-located or operated in

conjunction with any other antenna or transmitter.

The manufacturer is not responsible for any radio or TV

interference caused by unauthorized modifications to this

equipment.

Caution!

This equipment complies with FCC radiation exposure

limits set forth for an uncontrolled environment. This

equipment should be installed and operated at a

minimum distance of 20cm between the radiator and

your body

Radiation exposure statement

FCC ID: X4YNBL301P

5. If the computer you used to set up the router can

access the internet, it means that you have successfully

configured the device, and that other computers in the

LAN should also be able to do the same. If they don’t,

verify that the Internet Protocol is set to obtain the IP

and DNS settings automatically.

To do so, right click Network & Internet Settings

followed by Next, click on Ethernet. Network and

sharing center > Ethernet > Properties and select

Internet Protocol version 4 (TCP/IPv4). Finish by

clicking on Properties Obtain Obtain DNS server and

and IP address automatically. Please note that the

path indicated above relates to Windows 10. Other

operating systems may differ, so make sure to follow the

instructions of the operating system you are using. If

you later wish to customize your wireless router’s

configurations, login to the router and click on the

corresponding menu options you desire to customize.

Produkt Specifikationer

Mærke:	Nexxt
Kategori:	Router
Model:	NCR-N301
Bredde:	200.66 mm
Dybde:	111.76 mm
Højde:	35.56 mm
Vægt:	589.67 g
Produktfarve:	Sort
Produkttype:	Bordplade router
Opbevaringstemperatur (T-T):	-40 - 70 °C
Relativ luftfugtighed ved drift (H-H):	10 - 90 %
Relativ luftfugtighed ved opbevaring (H-H):	5 - 90 %
Ethernet LAN-porte (RJ-45):	4
Ethernet LAN:	Ja
Wi-Fi-standarder:	802.11b,802.11g,Wi-Fi 4 (802.11n)
Forældrekontrol:	Ja
Driftstemperatur (T-T):	0 - 40 °C
Ethernet LAN-datahastigheder:	10,100 Mbit/s
Sikkerhedsalgoritmer:	AES,TKIP,WPA,WPA2-PSK
Husmateriale:	Acrylonitrilbutadienstyren
Ethernet WAN:	Ja
WAN forbindelsestype:	RJ-45
Wi-Fi-bånd:	Enkelt band (2,4 GHz)
Bedste Wi-Fi standard:	Wi-Fi 4 (802.11n)
WLAN dataoverførselshastighed (maks):	300 Mbit/s
WLAN dataoverførselshastighed (første bånd):	300 Mbit/s
Ethernet LAN-grænsefladetype:	Hurtigt ethernet
Kabelteknologi:	10/100Base-T(X)
Netværksstandarder:	IEEE 802.3,IEEE 802.3u
Portvideresendelse:	Ja
DHCP-klient:	Ja
DHCP-server:	Ja
Universal Plug and Play (UPnP):	Ja
Antennedesign:	Ekstern
Antenner, antal:	4
Knap til nulstilling:	Ja
Firewall:	Ja
Filtrering:	Ja
Strømkilde type:	DC
Udgangsspænding:	9 V
Udgangsstrøm:	0.6 A
Antal kanaler:	13 kanaler
Niveau for antennestyrke (maks.):	5 dBi
Dynamisk DNS (DDNS):	Ja
Understøttelse af DMZ:	Ja
Trådløs radio:	Ja
VPN gennemløb:	Ja
Båndbreddekontrol:	Ja