Oregon Scientific BHM612A Manual


Læs gratis den danske manual til Oregon Scientific BHM612A (4 sider) i kategorien Ur. Denne vejledning er vurderet som hjælpsom af 64 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 32.5 anmeldelser. Har du et spørgsmål om Oregon Scientific BHM612A, eller vil du spørge andre brugere om produktet?

Side 1/4
1
GB
ARF SIGNAL INDICATOR
- Indicates the signal-receiving status of the unit
BMAIN WINDOW
- Displays the current time with seconds or day-of-the week
CSECONDARY WINDOW
- Displays the alarm time and its status or date
D[ MODE/SET ] button
- Changes between seconds and weekday display (Main
window) or between calendar and alarm clock display
(secondary window)
- Holds to activate the clock setting mode
E[ UP ] button
- Increases the value of a setting by one unit
F[ ZONE ] button
- Press to sequence through the 4 U.S. time-zones: Pacific,
Mountain, Central or Eastern.
G[ALARM] button
- Changes the display and operating status of the alarm
clock
H[RESET] button
- Returns all settings to the factory set default values
BATTERY INSTALLATION
1. Open the battery compartment by removing the screw at the
bottom of the unit.
2. Pull out the battery holder and insert two AAA-sized (UM-4)
batteries in accordance with the polarities shown.
3. Slide back the battery holder into the compartment and fasten
the screw.
4. Press RESET with a blunt stylus.
5. When the low battery indicator [ appears on the display, ]
follow the above procedures to replace the unit with new
batteries.
Note The unit will automatically search for the radio signal
when batteries are first installed. When the BHM-612A is
new and just out of the box, allow up to 72 hours for the
unit to receive the US Atomic Clock signal. To facilitate
reception, place the BHM-612A on a window sill away
from other signal emitting equipment such as TVs, radios,
PCs and microwaves. Stronges signal reception is be-
tween midnight and 4AM.
INTRODUCTION
Congratulations on purchasing the BHM-612A Radio Controlled
Alarm Clock.
A smart-looking and easy-to-operate timepiece, the BHM-612A
is designed to automatically synchronize the current time and
date with the U.S. Atomic Clock.
The BHM-612A is also equipped with a daily alarm clock plus
date and multilingual weekday display.
FEATURES & KEY CONFIGURATION
RADIO CONTROLLED ALARM CLOCK
MODEL : BHM-612A
USER’S MANUAL
A
B
C
D
F
G
E
H
2
GB
HOW TO ENABLE OR DISABLE AUTO-
RECEPTION
To disable the automatic signal reception feature and cause the
BHM-612A to operate as a quartz clock, hold down for[ZONE]
three seconds.
To enable the feature again, hold down the [UP] button for three
seconds. The RF signal display will start scanning to initiate
reception automatically.
HOW TO SET THE CALENDAR CLOCK
MANUALLY
When the current time is displayed:
Press for two seconds. Hours digits will[ MODE / SET ]
flash.
Set the hour using [ UP ].
Press . Minutes digits will flash.[ MODE / SET ]
Set the minutes using [ UP ].
Press [ MODE / SET ].
Follow the same pattern to enter year, month, day and the
display language for the weekday. You can choose among E
(English) F (French), and S (Spanish).
Press to save the changes and exit.[ MODE / SET ]
If changes are made during the process, the seconds of the clock
will reset and start from zero. The unit will also save all changes
and return to normal display automatically after the unit has been
left idle for a minute.
HOW TO SET AND USE THE ALARM
To set the alarm time:
1. Press [ ALARM] to display the alarm time.
2. Press and hold [ ALARM ] for two seconds. Hours digits
will flash.
3. Set the hours using [ UP ].
4. Press [ALARM ]. Minutes digits will flash.
5. Set the minutes using [ UP ].
6. Press [ ALARM ] to save and exit. The alarm clock will be
activated automatically during the setting procedure.
To activate or deactivate the alarm during normal display.
Press to display the alarm time.[ ALARM ]
Press to change the status of the alarm. The[ ALARM ]
respective indicator will appear.
When the alarm goes off, the alarm sound will gradually increase
in volume and speed. The alarm will continue to sound for
approximately two minutes unless interrupted when any button
is pressed. If the alarm is not interrupted, after 2 minutes the
alarm will silence itself and reactivate after approximately eight
minutes.
Battery
Holder
Screw
DISPLAY MODES
In normal display, the current time, with seconds, will be
displayed in the main window and the date will be displayed in
the secondary window.
To display the weekday in the main window, press
[ MODE / SET ] once. Press the button again to display seconds.
To display the alarm time in the secondary window, press
[ ALARM ] [ MODE / SET ] once. Press to display the date.
ABOUT RECEPTION OF RADIO SIGNAL
The BHM-612A is designed to automatically synchronize its
current time and date when within range of the U.S. Atomic
Clock.
When the unit is within range, its radio-control mechanism will
override all manual settings. The benefit of a RF controlled
clock is sustained accuracy without the need of manual adjustment.
Complete signal reception generally takes about 2 to 10 minutes,
depending on the strength of the radio signal. When the reception
is completed, the signal display will be stable. After that, the
periodical scanning will only take a few seconds.
For better reception of radio signals, place the clock away from
metal objects and electrical appliances to minimize interference.
SIgnal Search Mode.
Signal Reception Mode
No Signal Received


Produkt Specifikationer

Mærke: Oregon Scientific
Kategori: Ur
Model: BHM612A

Har du brug for hjælp?

Hvis du har brug for hjælp til Oregon Scientific BHM612A stil et spørgsmål nedenfor, og andre brugere vil svare dig