Oregon Scientific WMR 112 Manual

Oregon Scientific Vejrstation WMR 112

Læs gratis den danske manual til Oregon Scientific WMR 112 (77 sider) i kategorien Vejrstation. Denne vejledning er vurderet som hjælpsom af 6 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 3.5 anmeldelser. Har du et spørgsmål om Oregon Scientific WMR 112, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/77

CABLE FREE WEATHER

STATION

MODEL: WMR112 / WMR112U (UK VERSION)

USER’S MANUAL

SECTION 1 INTRODUCTION

Congratulations on your purchasing the WMR112/112U Cable Free

Weather Station. An all-purpose easy-to-use system, the WMR112/

112U lets you monitor the following weather elements:

-Air temperature

-Relative humidity

-Barometric pressure

-Wind speed and direction

-Rainfall

The WMR112/112U is also equipped with:

-RF calendar clock with daily alarm

-Weather forecast within 32 to 48 km (20- to 30-mile) radius

-Weather alarms

-Memory for maximum and minimum readings

-Touch-screen plus key button operation

STANDARD PACKAGE

The original WMR112/112U comes complete with the following:

-Main unit (WMR112/112U)

-Anemometer (WGR918N)

-Thermo-hygrometer (THGN228NX)

-Rain gauge (PCR918N)

-Baro-thermo-hygrometer (BTHR918N)

-12V AC adapter

The rain gauge is powered by solar transmitter STR928N while the

anemometer is powered by solar transmitter STR938.

The WMR112/112U can support up to seven diﬀerent remote

instruments. You can connect up to three optional thermo or thermo-

hygro sensors to the system.

Optional items include:

-Thermo-hygro sensor (THGR228N/THGR238N)

-Thermo sensor (THR228N/THR238N)

Contact an authorized dealer for optional items.

SECTION 2 INSTALLATION

The WMR112/112U operates at 433MHz. No wire installation is

required among units.

The WMR112/112U has an eﬀective range of 100 meters in an open

area. Position the units within the range and be sure the transmission

path is clear of interference and obstacles.

Note: The anemometer, thermo-hygrometer and rain gauge should

be installed outdoors and in locations that best measure the weather

elements which the instruments are designed for. As for the baro-

thermo-hygrometer, it must be installed indoors. If you have any

optional thermo or thermo-hygro sensors, they can be installed

outdoors or indoors.

THE ANEMOMETER

The anemometer measures wind speed and direction.

To install it,

1. Unscrew the solar transmitter STR938.

2. Plug in the connector of WGR918N into the solar transmitter as

shown.

3. Secure the screws again.

4. Place the wind cup over the thinnest shaft on the anemometer’s

T-bar.

5. Tighten the screw on the base of the wind cup.

6. Align the red markings on the wind vane’s shaft.

7. With the aid of a compass, face the red marking south before

mounting the anemometer.

8. Mount the anemometer and its solar transmitter safely in place.

The wind speed and direction window on the main unit should read

180 if the main unit is installed.°

9. Press [RESET] of STR938 after installation.

THE THERMO-HYGROMETER

The thermo-hygrometer measures outdoor temperature and humidity.

It uses two (2) UM-4 or “AAA” size batteries.

Follow these steps to install / replace batteries:

1. Remove the screws on the battery compartment.

2. Insert the batteries strictly according to the polarities shown

therein.

3. Replace the battery compartment door and secure its screws.

4. Press the [RESET] button.

THE RAIN GAUGE

The rain gauge measures the total amount and rate of rainfall.

To install it:

1. Unscrew the solar transmitter STR928N.

2. Plug in the connector of PCR918N into the solar transmitter as

shown.

3. Secure the screws again.

4. Open the cover of the rain collector.

5. Remove the ﬁber tape from around the bucket assemblies.

6. Mount the rain gauge and its solar transmitter safely in place.

7. Put drops of water on the cross at the base on the rain collector

to check the leveling.

8. Use metal ring to adjust the leveling of the rain collector if

necessary.

9. Close the cover of the rain collector.

10. Press [RESET] of STR928N after installation.

THE SOLAR TRANSMITTERS

The solar transmitters make use of solar energy to power the

instruments they are connected to. Two pieces of UM3 or "AA" -

sized batteries are needed as back-up power.

Note: It is recommended to insert two UM3 or “AA”-sized super

lithium batteries for weather condition under 0 °C.

For the solar transmitters to function properly, make sure the solar

receptors on the transmitters are exposed to sunlight and the

connectors of the connection cable are securely plugged in.

Water stay at

position 1 - 4

means the gauge

is not leveled

METAL RING

Produkt Specifikationer

Mærke:	Oregon Scientific
Kategori:	Vejrstation
Model:	WMR 112

Har du brug for hjælp?

Hvis du har brug for hjælp til Oregon Scientific WMR 112 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Vejrstation Oregon Scientific Manualer

Oregon Scientific BAR310HG Manual

12 Januar 2025

Oregon Scientific BAR 898 Manual

11 Januar 2025

Oregon Scientific WMR180 Manual

31 December 2025

Oregon Scientific RMR203HG Manual

31 December 2025

Oregon Scientific THC138 Manual

31 December 2025

Oregon Scientific WMR 300 Manual

31 December 2025

Oregon Scientific RAA 501 H Manual

31 December 2025

Oregon Scientific Alizé BAR268HGA Manual

14 December 2024

Oregon Scientific BAR206X Manual

2 September 2024

Oregon Scientific BAR 888A Manual

1 September 2024

Vejrstation Manualer

Nyeste Vejrstation Manualer

La Crosse Technology WS7006 Manual

30 September 2025

23 September 2025

23 September 2025

23 September 2025

21 September 2025

Brandson 305419 Manual

15 September 2025

Brandson 306643 Manual

15 September 2025

Brandson 304632 Manual

15 September 2025

Brandson 304577 Manual

14 September 2025

Brandson 304465 Manual

14 September 2025