Panasonic CY-111B-P Manual

Panasonic Ikke kategoriseret CY-111B-P

Læs gratis den danske manual til Panasonic CY-111B-P (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 31 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 16 anmeldelser. Har du et spørgsmål om Panasonic CY-111B-P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

INSTRUCTIONS

Cylindrical Photoelectric Sensor

CY-111, CY-19 CY-12 Seriesq, q

Thank you for purchasing products from Panasonic. Please read this

Instruction Manual carefully and thoroughly for the correct and optimum

use of this product. Kindly keep this manual in a convenient place for quick

reference.

WARNING

●Never use this product as a sensing device for personnel protection.

●In case of using sensing devices for personnel protection, use prod-

ucts which meet laws and standards, such as OSHA, ANSI or IEC

etc., for personnel protection applicable in each region or country.

1Cautions

●This product has been developed / produced for industrial use only.

●This product is suitable for indoor use only. The cable extension up to

a total of 10m or less with a strength of 0.34mm

2 or less (each emitter

and receiver of the thru-beam type) is possible.

●Make a cable length as short as possible to lessen noise pickup.

●Make sure that the power supply is off while wiring.

●Verify that the supply voltage including the ripple is within the rating.

●If power is supplied from a commercial switching regulator, ensure that

the frame ground (F.G.) terminal of the power supply is connected to

an actual ground.

●Shortcircuiting the load or wrong wiring may burn or damage the

product.

●Ensure that an isolation transformer is utilized for the DC power sup-

ply. If an autotransformer is utilized, the main body or power supply

may be damaged.

●If the used power supply generates a surge, connect a surge absorber

to the power supply to absorb the surge.

●Do not use the sensor during the initial transient time (0.5 sec) after

the power supply is switched on.

●Do not run the wires together with high-voltage lines or power lines

or put them in the same raceway. This can cause malfunction due to

induction.

● Avoid using the product where there are strong magnetic elds as they

may prevent the product from working according to the specication.

● Take care that the sensor is not directly exposed to a uorescent lamp

from a rapid-starter lamp or a high frequency lighting device, as it may

affect the sensing performance.

●Protect the sensor from water, oil, grease, organic solvents such as

thinner, etc., strong acid, and alkaline.

●Avoid using a product where there is excessive vapor, dust or cor-

rosive gases, or in a place where it could be exposed directly to water

or chemicals.

● This product cannot be used in an environment containing inam-

mable or explosive gases.

●Never disassemble or modify the product.

2Compliance with standards and directives

This product complies with the following standards and

regulations.

●For the EU: EMC Directive 2004/108/EC

●For the US and Canada:

ANSI/UL60947-5-2, CAN/CSA C22.2 No.14

●For Korea: S1-G-1-2009, S2-W-5-2009

* In case you require a UL listing mark or C-UL

listing mark, use a class 2 power supply unit.

RoHS directive

●This equipment complies with RoHS (CE and Chinese

directive).

3Sensor types

Cable type (2m) Connector type (M12)

Standard

Side view

4Part description

124

3 3

1Main body

2Mounting plate

3Nut

4Cable with connector

5Mounting

General installation hints

1. Attach the sensor directly on your equipment or use one of the optional

mounting brackets to x the sensor.

2. The tightening torque should be 3Nm or less.

3. If you mount a M12 connector type, you can use the optional cable with

the connector UZZ812 D. The tightening torque for the connector part qq

should be 3Nm or less.

Mounting with the mounting bracket MS-CY1-1

1. Using the holes indicated

1, screw the mounting

bracket to the surface.

2. Feed the sensor into the

mounting hole and 2

afx it with the nuts on the

sensor.

Mounting with the mounting bracket MS-CY1-2

1. Using the holes indicated

1, screw the mounting

bracket to the surface.

2. Feed the sensor into the

mounting hole and 2

adjust its direction.

3. Use the upper two screws

3 to secure the sensor.

Model no. Description

MS-CY1-1 Material: Stainless steel

MS-CY1-2 Material: Plastic (recommended for a more exible beam axis

alignment)

6Mating cables

There are two types of mating cables: straight type and elbow type. You

only need mating cables for the connector type (M12).

Straight type Elbow type

Cable type Model no. Description

Straight

UZZ81220D Length: 2m

UZZ81250D Length: 5m

Elbow

UZZ81221D Length: 2m

UZZ81251D Length: 5m

7Reectors

Square form Hexagonal form

Reective tape

Reector form Model no. Description

Square RF-420 50 x 50mm

Hexagonal RF-410 24 x 21mm

Reective tape RF-40RL5 22 x 5m, thickness: 0.4mm

8Wiring diagrams

Emitter of thru-beam type







WR9'&



±％

9LROHW,QSXW

%OXH9

%URZQ9

Receiver of thru-beam / reective type (NPN)









±％

/RDG

WR9'&

%ODFN2XWSXW

%URZQ9

%OXH9

Receiver of thru-beam / reective type (PNP)









±'&％

/RDG

WR9

%URZQ9

%OXH9

%ODFNRXWSXW

9Terminal arrangement

M12 connector

1 2

4 3

Terminal no. Function

1+V

2Input (only emitter of thru-beam type)

30V

4Output (only receiver of thru-beam and reec-

tive type)

* Make sure to insulate the ends of all unused lead wires.

10 Detection curves

Thru-beam type

-15

15 m

10 m

ø 12 mm

A = Sensing range

Diffuse reective type

1 5

10 cm

-1

1.4

-1.4

Object 10 x 10cm; 1= White 90%, = Gray 18%2

Produkt Specifikationer

Mærke:	Panasonic
Kategori:	Ikke kategoriseret
Model:	CY-111B-P

Har du brug for hjælp?

Hvis du har brug for hjælp til Panasonic CY-111B-P stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panasonic Manualer

Panasonic CS-BKP Manual

1 Juli 2025

Panasonic CS_CU-E9CKP Manual

1 Juli 2025

Panasonic CQ-DPX151U Manual

30 Juni 2025

Panasonic CS-2C19BKP5G Manual

30 Juni 2025

Panasonic CS-C24 Manual

29 Juni 2025

Panasonic CS-12CKE Manual

29 Juni 2025

Panasonic CS-E15CKP Manual

27 Juni 2025

Panasonic CS-E12 Manual

27 Juni 2025

Panasonic CS-V24BKP Manual

24 Juni 2025

Panasonic CS-V18 Manual

24 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Schneider LUCD1XES Manual

4 Juli 2025

Ikea BLÄDDRARE 304.743.99 Manual

4 Juli 2025

NUX Komp Core Deluxe MKII Manual

4 Juli 2025

Ikea GRÖNAMARANT 204.604.25 Manual

4 Juli 2025

Rowenta Focus DW5121 Manual

4 Juli 2025

Racktime Baskit Breeze 2.0 Manual

4 Juli 2025

Schneider KSB32CP15D Manual

4 Juli 2025

Wiesenfield WIE-IN-100 Manual

4 Juli 2025

Ergotec PM-705N Manual

4 Juli 2025

Sol Expert 19590 Manual

4 Juli 2025