Panasonic DP-101A-M-P Manual

Panasonic Ikke kategoriseret DP-101A-M-P

Læs gratis den danske manual til Panasonic DP-101A-M-P (9 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.8 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Panasonic DP-101A-M-P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/9

MEUML-DP100 V1.1

Thank you for purchasing products from Panasonic Electric Works SUNX

Co., Ltd. Please read this Instruction Manual carefully and thoroughly for

the correct and optimum use of this product. Kindly keep this manual in a

convenient place for quick reference.

This product has been developed / produced for industrial use only.

Use within the rated pressure range.

Do not apply pressure exceeding the pressure resistance value. The

diaphragm will be damaged resulting in faulty operation.

Make sure that the power supply is o while wiring.

Incorrect wiring will damage the sensor.

Verify that the supply voltage including the ripple is within the rating.

If power is supplied from a commercial switching regulator, ensure that

the frame ground (F.G.) terminal of the power supply is connected to an

actual ground.

In case noise generating equipment (switching regulator, inverter motor,

etc.) is used in the vicinity of this sensor, connect the frame ground (F.G.)

terminal of the equipment to an actual ground.

Do not use during the initial transient time (0.5s) after the power supply is

switched on.

Do not run the wires together with high-voltage lines or power lines or put

them in the same raceway. This can cause malfunction due to induction.

The specication may not be satised in a strong magnetic eld.

Avoid dust, dirt, and steam.

Take care that the sensor does not come in direct contact with water, oil,

grease, or organic solvents such as thinners, etc.

Do not insert wires, etc., into the pressure port. The diaphragm will be

damaged resulting in faulty operation.

Do not operate the keys with pointed or sharp objects.

Do not apply stress directly to the sensor cable joint by forcibly bending

or pulling.

Use a 12mm end wrench (14mm for DP-100-E type) when tightening a

commercial coupler to the pressure port. The tightening torque should be

9.8N·m or less (M5 female connector: 1N·m or less). The commercial

coupler or pressure port section will be damaged if the tightening torque is

excessive.

Wrap sealing tape around the coupler when connecting to prevent leaks.

INSTRUCTION MANUAL

WARNING

• Never use this product as a sensing device for personnel protection.

• In case of using sensing devices for personnel protection, use

products which meet laws and standards, such as OSHA, ANSI or

IEC etc., for personnel protection applicable in each region or

country.

• DP-100 series is designed for use with non-corrosive gas. It cannot

be used for liquid or corrosive gas.

• Japanese Measurement Laws prohibit the use of this product in

Japan.

1CAUTIONS

2PART NAMES

No. Part Description

1Output 1 opera-

tion indicator

Lights up when comparative output 1 is

2Output 2 / analog

voltage operation

indicator

•Standard type: lights up when

comparative output 2 is ON

•Multifunction type: lights up when

analog voltage output is ON

3Pressure unit dis-

play

Depending on the model, “MPa” or “kPa”

appears here. If you set another pressure

unit, attach the appropriate label, e.g. psi,

bar, etc.

4Main display Large 4-character LCD display.

5Sub-display Small 4-character LCD display.

6Mode selection

key

For details, see page 3, section 8,

SELECTING MODES.

7Up key Increases value being set.

8Down key Decreases value being set.

94-pin male con-

nector

See “Pin assignment, 4-pin male connec-

tor” on page 2.

0Pressure port • DP-100 type: R1/8 + M5 female screw

• DP-100-E type: G1/8 + M5 female

screw

• DP-100-M type: M5 female screw

• DP-100-N type: NPT1/8 + M5 female

screw

3PIPING

㧝

DP-100

876

12mm end wrench

Pressure Sensor

For use outside Japan

High-performance Digital Display

DP-100 Series

Produkt Specifikationer

Mærke:	Panasonic
Kategori:	Ikke kategoriseret
Model:	DP-101A-M-P

Har du brug for hjælp?

Hvis du har brug for hjælp til Panasonic DP-101A-M-P stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panasonic Manualer

Panasonic SoundSlayer SC-GNW30 Manual

25 November 2025

Panasonic MX-HG4401 Manual

10 Oktober 2025

Panasonic EY3794 Manual

8 Oktober 2025

Panasonic CS-ME14CB1P Manual

1 Oktober 2025

Panasonic AV-HSW10 Manual

18 September 2025

Panasonic SD3-A1 Manual

15 September 2025

Panasonic PT-DW5100 Manual

27 August 2025

Panasonic PT-D4000 Manual

26 August 2025

Panasonic NB-G211 Manual

14 August 2025

Panasonic NN-TK81KC Manual

13 August 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Waterstone 7800 Manual

11 December 2025

Kwikset 258 Manual

11 December 2025

Schlage F170 Manual

11 December 2025

Moen Align 7565EV Manual

11 December 2025

Energy Sistem ESG M3 Neon Manual

11 December 2025

ALNO MC10244 Manual

11 December 2025

JET TAK-ZX Manual

11 December 2025

Crosley Nashville CF1165 Manual

11 December 2025

Waterstone 1455 Manual

11 December 2025

Laica NE2015 Manual

11 December 2025