Panasonic DP-101ZL3-M-P Manual

Panasonic Ikke kategoriseret DP-101ZL3-M-P

Læs gratis den danske manual til Panasonic DP-101ZL3-M-P (9 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 53 personer og har en gennemsnitlig bedømmelse på 4.5 stjerner ud af 27 anmeldelser. Har du et spørgsmål om Panasonic DP-101ZL3-M-P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/9

MEUML-DP100 V1.1

Thank you for purchasing products from Panasonic Electric Works SUNX

Co., Ltd. Please read this Instruction Manual carefully and thoroughly for

the correct and optimum use of this product. Kindly keep this manual in a

convenient place for quick reference.

This product has been developed / produced for industrial use only.

Use within the rated pressure range.

Do not apply pressure exceeding the pressure resistance value. The

diaphragm will be damaged resulting in faulty operation.

Make sure that the power supply is o while wiring.

Incorrect wiring will damage the sensor.

Verify that the supply voltage including the ripple is within the rating.

If power is supplied from a commercial switching regulator, ensure that

the frame ground (F.G.) terminal of the power supply is connected to an

actual ground.

In case noise generating equipment (switching regulator, inverter motor,

etc.) is used in the vicinity of this sensor, connect the frame ground (F.G.)

terminal of the equipment to an actual ground.

Do not use during the initial transient time (0.5s) after the power supply is

switched on.

Do not run the wires together with high-voltage lines or power lines or put

them in the same raceway. This can cause malfunction due to induction.

The specication may not be satised in a strong magnetic eld.

Avoid dust, dirt, and steam.

Take care that the sensor does not come in direct contact with water, oil,

grease, or organic solvents such as thinners, etc.

Do not insert wires, etc., into the pressure port. The diaphragm will be

damaged resulting in faulty operation.

Do not operate the keys with pointed or sharp objects.

Do not apply stress directly to the sensor cable joint by forcibly bending

or pulling.

Use a 12mm end wrench (14mm for DP-100-E type) when tightening a

commercial coupler to the pressure port. The tightening torque should be

9.8N·m or less (M5 female connector: 1N·m or less). The commercial

coupler or pressure port section will be damaged if the tightening torque is

excessive.

Wrap sealing tape around the coupler when connecting to prevent leaks.

INSTRUCTION MANUAL

WARNING

• Never use this product as a sensing device for personnel protection.

• In case of using sensing devices for personnel protection, use

products which meet laws and standards, such as OSHA, ANSI or

IEC etc., for personnel protection applicable in each region or

country.

• DP-100 series is designed for use with non-corrosive gas. It cannot

be used for liquid or corrosive gas.

• Japanese Measurement Laws prohibit the use of this product in

Japan.

1CAUTIONS

2PART NAMES

No. Part Description

1Output 1 opera-

tion indicator

Lights up when comparative output 1 is

2Output 2 / analog

voltage operation

indicator

•Standard type: lights up when

comparative output 2 is ON

•Multifunction type: lights up when

analog voltage output is ON

3Pressure unit dis-

play

Depending on the model, “MPa” or “kPa”

appears here. If you set another pressure

unit, attach the appropriate label, e.g. psi,

bar, etc.

4Main display Large 4-character LCD display.

5Sub-display Small 4-character LCD display.

6Mode selection

key

For details, see page 3, section 8,

SELECTING MODES.

7Up key Increases value being set.

8Down key Decreases value being set.

94-pin male con-

nector

See “Pin assignment, 4-pin male connec-

tor” on page 2.

0Pressure port • DP-100 type: R1/8 + M5 female screw

• DP-100-E type: G1/8 + M5 female

screw

• DP-100-M type: M5 female screw

• DP-100-N type: NPT1/8 + M5 female

screw

3PIPING

㧝

DP-100

876

12mm end wrench

Pressure Sensor

For use outside Japan

High-performance Digital Display

DP-100 Series

The sensor mounting bracket (MS-DP1-1) is available as an option.

When mounting the sensor onto the sensor mounting bracket, etc., the

tightening torque should be 0.5N·m or less.

The panel mounting bracket MS-DP1-2 (optional) and MS-DP1-4

(optional), as well as the front cover MS-DP1-3 (optional) and DPX-04

(optional) are also available.

The type of the front cover diers depending on the mounting bracket.

Use MS-DP1-3 for MS-DP1-2, and DPX-04 for MS-DP1-4.

To mount the panel mounting bracket, refer to the Instruction Manual

enclosed with MS-DP1-2 or MS-DP1-4.

Connection method

Attach the female connector of cable

CN-14A- to the 4-pin male connector.

Disconnection method

While pressing the release lever, pull out

the connector.

Pin assignment, 4-pin male connector

Notes:

When using the analog voltage output, pay careful attention to the

connected device’s input impedance.

If the cable is extended, the cable resistance will cause the voltage to

drop.

NPN output type

Standard type

Multifunction type

PNP output type

Standard type

Multifunction type

The EASY mode, hysteresis mode or window comparator mode can be

selected as the output mode for comparative output 1 and, for the standard

type DP-100, comparative output 2.

For details, see page 5, section 10, MENU SETTING MODE.

Easy mode

The comparative output is turned ON or OFF (depending on the N.O./N.C.

setting) when the threshold is reached. The tolerance of the threshold is

specied by the hysteresis setting. For details, see page 6, section 11, PRO

MODE.

4MOUNTING

No. Part Description

1M3 (length 6mm) screws

with washers

Accessory with MS-DP1-1

2Sensor mounting bracket

(MS-DP1-1)

Optional

5WIRING

Pin no. Terminal name

1+V

2Comparative output 1

3• Standard type: Comparative

output 2

• Multifunction type: Analog

voltage output or external input

40V

6I/O CIRCUIT DIAGRAMS

CN-14A-Cغ

Contact: SPHD-001T-P0.5

Housing: PAP-04V-S

[JST Mfg. Co., Ltd.]

Release lever

e w

ith

ema

connector

Ԙ ԙ Ԛ ԛ

㧝

7OUTPUT MODE AND OUTPUT OPERATION

Notes: • Hysteresis can be xed in 8 levels.

For details, see page 6, section 11, PRO MODE.

•P-1 is displayed for comparative output 1 and P-2 for

comparative output 2 on the sub-display.

User’s circuitInternal circuit

12 to 24V DC

±10%

(Black)

Comparative output 1

Main circuit

(White) Comparative output 2

(Blue) 0V

100mA max.

Load

(Brown) +V

Color code of cable with connector

_±10%

1kǡ

Main circuit

Users' circuitInternal circuit

(Black) Comparative output 1

(Blue) 0V

100mA max.

Load

(Brown) +V

Color code of cable with connector

12 to 24V DC

(White)

Analog voltage output

or external input

_±10%

100mA max.

Main circuit

User’s circuitInternal circuit

(Black) Comparative output 1

(White) Comparative output 2

(Blue) 0V

100mA max.

Load

(Brown) +V

Color code of cable with connector

12 to 24V DC

_±10%

1kǡ12 to 24V D

Main circuit

(Black) Comparative output 1

User’s circuitInternal circuit

(Blue) 0V

100mA max.

Load

(Brown) +V

Color code of cable with connector

(White)

Analog voltage output

or external input

H (Hysteresis)

OFF

Pressure

Comparative

output

Produkt Specifikationer

Mærke:	Panasonic
Kategori:	Ikke kategoriseret
Model:	DP-101ZL3-M-P

Har du brug for hjælp?

Hvis du har brug for hjælp til Panasonic DP-101ZL3-M-P stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panasonic Manualer

Panasonic CS-BKP Manual

1 Juli 2025

Panasonic CS_CU-E9CKP Manual

1 Juli 2025

Panasonic CQ-DPX151U Manual

30 Juni 2025

Panasonic CS-2C19BKP5G Manual

30 Juni 2025

Panasonic CS-C24 Manual

29 Juni 2025

Panasonic CS-12CKE Manual

29 Juni 2025

Panasonic CS-E15CKP Manual

27 Juni 2025

Panasonic CS-E12 Manual

27 Juni 2025

Panasonic CS-V24BKP Manual

24 Juni 2025

Panasonic CS-V18 Manual

24 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Schneider LUCD1XES Manual

4 Juli 2025

Ikea BLÄDDRARE 304.743.99 Manual

4 Juli 2025

NUX Komp Core Deluxe MKII Manual

4 Juli 2025

Ikea GRÖNAMARANT 204.604.25 Manual

4 Juli 2025

Rowenta Focus DW5121 Manual

4 Juli 2025

Racktime Baskit Breeze 2.0 Manual

4 Juli 2025

Schneider KSB32CP15D Manual

4 Juli 2025

Wiesenfield WIE-IN-100 Manual

4 Juli 2025

Ergotec PM-705N Manual

4 Juli 2025

Sol Expert 19590 Manual

4 Juli 2025