Panasonic EX-13SEB-PN Manual

Panasonic Ikke kategoriseret EX-13SEB-PN

Læs gratis den danske manual til Panasonic EX-13SEB-PN (3 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 38 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 19.5 anmeldelser. Har du et spørgsmål om Panasonic EX-13SEB-PN, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/3

MEUEN-EX10 V2.0

Thank you for purchasing products from Panasonic Electric Works SUNX

Co., Ltd. Please read this Instruction Manual carefully and thoroughly for

the correct and optimum use of this product. Kindly keep this manual in a

convenient place for quick reference.

This product has been developed / produced for industrial use only.

For the convergent reective type EX-14, maintain adequate distance

from reective objects in the background, e.g. conveyors, since they may

adversely effect sensing.

A thin 0.1mm2 cable is used for this product. Do not use excessive force

when pulling on the cable: it may cause cable to break.

Make sure that the power supply is o while wiring.

Incorrect wiring will damage the sensor.

Verify that the supply voltage including the ripple is within the rating.

Verify that the supply voltage variation is within the rating.

If power is supplied from a commercial switching regulator, ensure that

the frame ground (F.G.) terminal of the power supply is connected to an

actual ground.

In case noise generating equipment (switching regulator, inverter motor,

etc.) is used in the vicinity of this product, connect the frame ground

(F.G.) terminal of the equipment to an actual ground.

Do not run the wires together with high-voltage lines or power lines or put

them in the same raceway. This can cause malfunction due to induction.

You can extend the cable up to 50m max. with 0.3mm

2 or more cable for

both emitter and receiver. However, in order to reduce noise, make the

wiring as short as possible.

Do not use during the initial transient time (0.5s) after the power supply is

switched on.

Ensure that the sensor is not directly exposed to the following light

sources as they may adversely eect sensing performance: uorescent

light from a rapid-starter lamp, a high frequency lighting device, sunlight

etc.

This sensor is suitable for indoor use only.

Avoid dust, dirt and steam. Do not use this sensor in places having

excessive vapor, dust, etc., or where it may come in direct contact with

corrosive gas.

Take care that the sensor does not come in contact with oil, grease,

organic solvents such as thinner, etc., strong acid, or alkalines.

Do not apply stress directly to the sensor cable joint by forcibly bending

or pulling.

Since the cable end is not waterproof, do not use the sensor in an

application where water could seep in from the cable end.

The tightening torque should be 0.2N·m or less.

Mounting using tapped holes

Side sensing

Front sensing

When using the attached screws and nuts

Side sensing

Front sensing

INSTRUCTION MANUAL

Photoelectric Sensor Ultra-slim type

EX-10 Series

WARNING

• Never use this product as a sensing device for personnel protection.

• In case of using sensing devices for personnel protection, use

products which meet laws and standards, such as OSHA, ANSI or IEC

etc., for personnel protection applicable in each region or country.

1CAUTIONS

2MOUNTING

11mm

M2 x 0.4mm ø

10mm M2

6mm

Sensing direction

11mm

M2 x 0.4mm ø

7mm

8mm M2

Sensing direction

11mm

10mm M2

Thickness of mounting plate: 2mm or less

Flat washers

Spring washers

Sensing direction

11mm

8mm M2

Thickness of mounting plate: 2.5mm or less

Sensing direction

Flat washers

Spring washers

When mounting the sensor with the optional mounting bracket, use the

attached M2 screws. The tightening torque should be 0.2N·m or less.

Six types of optional sensor mounting brackets are available.

Optional slit masks help the sensor detect small objects. The accuracy of

the position being sensed is also increased. However, the sensing range is

reduced.

Attach the slit mask to the sensor before mounting the sensor.

If both the slit mask and the mounting bracket MS-EX10-1 or MS-EX10-11

are attached to the front sensing type sensor, use a spacer that is at least

0.2mm thick, as shown in the gure.

The following symbols are used in this section.

NPN output type

Only the thru-beam receiver incorporates the output.

PNP output type

Only the thru-beam receiver incorporates the output.

3MOUNTING BRACKETS

Model no. Description Material

MS-EX10-1 Mounting bracket for front sensing

type only.

Two 4mm M2 pan head screws

are attached.

MS-EX10-2 Mounting bracket for side sensing

type only.

Two 8mm M2 pan head screws

are attached.

Cold rolled car-

bon steel

(SPCC)

MS-EX10-3 L-shaped mounting bracket

Two 4mm and two 8mm M2 pan

head screws are attached.

MS-EX10-11 Mounting bracket for front sensing

type only.

Two 4mm M2 pan head screws

are attached.

MS-EX10-12 Mounting bracket for side sensing

type only.

Two 8mm M2 pan head screws

are attached.

Stainless steel

(SUS304)

MS-EX10-13 L-shaped mounting bracket

Two 4mm and two 8mm M2 pan

head screws are attached.

4SLIT MASKS

Model no. Description Material

OS-EX10-12 Slit mask for front sensing type

only. Slit diameter: 1.2mm.

OS-EX10-15 Slit mask for front sensing type

only. Slit diameter: 1.5mm.

Stainless steel

(SUS304)

OS-EX10E-12 *1

*1Excluding EX-19

Slit mask for side sensing type

only. Slit diameter: 1.2mm.

Spacers, at least 0.2mm thick

M2 screws

5I/O CIRCUIT DIAGRAMS

Symbol Meaning

D Reverse supply polarity protection diode

Z Surge absorption zener diodeD

Tr1NPN output transistor

Tr2PNP output transistor

±10%

Tr1

Color code

Sensor circuit

12 to 24V DC

Load

Users' circuitInternal circuit

(Brown) +V

(Black) Output (note)

(Blue) 0V 50mA max.

±10%

Tr2

Sensor circuit

Color code

(Brown) +V

Load

50mA max.

(Black) Output (Note)

(Blue) 0V

Users' circuit

Internal circuit

12 to 24V DC

Produkt Specifikationer

Mærke:	Panasonic
Kategori:	Ikke kategoriseret
Model:	EX-13SEB-PN

Har du brug for hjælp?

Hvis du har brug for hjælp til Panasonic EX-13SEB-PN stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panasonic Manualer

Panasonic CS-BKP Manual

1 Juli 2025

Panasonic CS_CU-E9CKP Manual

1 Juli 2025

Panasonic CQ-DPX151U Manual

30 Juni 2025

Panasonic CS-2C19BKP5G Manual

30 Juni 2025

Panasonic CS-C24 Manual

29 Juni 2025

Panasonic CS-12CKE Manual

29 Juni 2025

Panasonic CS-E15CKP Manual

27 Juni 2025

Panasonic CS-E12 Manual

27 Juni 2025

Panasonic CS-V24BKP Manual

24 Juni 2025

Panasonic CS-V18 Manual

24 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Schneider LUCD1XES Manual

4 Juli 2025

Ikea BLÄDDRARE 304.743.99 Manual

4 Juli 2025

NUX Komp Core Deluxe MKII Manual

4 Juli 2025

Ikea GRÖNAMARANT 204.604.25 Manual

4 Juli 2025

Rowenta Focus DW5121 Manual

4 Juli 2025

Racktime Baskit Breeze 2.0 Manual

4 Juli 2025

Schneider KSB32CP15D Manual

4 Juli 2025

Wiesenfield WIE-IN-100 Manual

4 Juli 2025

Ergotec PM-705N Manual

4 Juli 2025

Sol Expert 19590 Manual

4 Juli 2025