Panasonic EX22APN Manual

Panasonic Ikke kategoriseret EX22APN

Læs gratis den danske manual til Panasonic EX22APN (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Panasonic EX22APN, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

5SENSITIVITY ADJUSTMENT

Step

Turn the sensitivity adjuster fully counterclockwise

to the minimum sensitivity position, MIN.

In the light received condition, turn the sensitivity

adjuster slowly clockwise and conrm the point A

where the sensor enters the “Light” state operation.

In the dark condition, turn the sensitivity adjuster further

clockwise until the sensor enters the “Light” state op-

eration and then bring it back to conrm point B where

the sensor just returns to the “Dark” state operation.

If the sensor does not enter the “Light” state

operation even when the sensitivity adjuster is

turned fully clockwise, the position is point B.

4. The position at the middle of points A and B

is the optimum sensing position.

6CAUTIONS

●This product has been developed / produced for industrial use only.

●The thin cable (0.1mm2) is used for this product. Thus, take care that

if the cable is pulled with excessive force, it may cause cable break.

●EX-24□ are not incorporated with a sensitivity adjuster.

If there is a reflective object (conveyor, etc.) in the back-

ground, since it may affect the sensing, use these models

by keeping enough distance from the reective object.

● If a reective object is present in the background, the sensing

of EX-28□ may be affected. When setting the sensor, make

sure to conrm that the reective object has no effect. In case

the reective object affects the sensing, take measures such

as removing the reective object or coloring it in black, etc.

●If sensors are mounted close together and the ambient temperature is near

the maximum rated value, provide for enough heat radiation / ventilation.

●Make sure to carry out wiring in the power supply OFF condition.

●Take care that wrong wiring will damage the sensor.

●Verify that the supply voltage variation is within the rating.

●If power is supplied from a commercial switching regulator, ensure that the frame

ground (F.G.) terminal of the power supply is connected to an actual ground.

●In case noise generating equipment (switching regulator, inverter

motor, etc.) is used in the vicinity of this product, connect the frame

ground (F.G.) terminal of the equipment to an actual ground.

●Extension up to total 50m (each emitter and receiver

of thru-beam type), or less, is possible with 0.3mm

2, or

more of conductor area cable. However , the extension of

a power supply line and the output line less than 10m of

is acceptable in case using this product as conforming to

S-mark

●Do not run the wires together with high-voltage lines or power lines or put

them in the same raceway. This can cause malfunction due to induction.

●Do not use during the initial transient time (50ms) after the

power supply is switched ON.

● Take care that the sensor is not directly exposed to uorescent

lamp from a rapid-starter lamp, a high frequency lighting de-

vice or sunlight etc., as it may affect the sensing performance.

●This sensor is suitable for indoor use only.

●Do not use this sensor in places having excessive vapor, dust,

etc., or where it may come in contact with corrosive gas, etc.

●Take care that the sensor does not come in contact with oil, grease,

organic solvents such as thinner, etc., strong acid, or alkaline.

●This sensor cannot be used in an environment containing

inammable or explosive gases.

●Never disassemble or modify the sensor.

7RoHS DIRECTIVE

●This equipment complies with RoHS (EC and Chinese directive).

●Chinese RoHS indicates inclusion despite regulation

value. (Refer to Chinese part.)

Optimum position

INSTRUCTION

MANUAL

Amplier Built-in Ultra-compact Type Photoelectric Sensor

EX-20 Series

MJECK-EX20 No.0054-68V

Thank you very much for purchasing Panasonic products.

Please read this Instruction Manual carefully and thorough-

ly for the correct and optimum use of this product. Kindly

keep this manual in a convenient place for quick reference.

● Please refer “our web site (

http://panasonic.net/id/

pidsx/global

)”.

● Access method is “Download” → “Manual”→ “Model No.”.

●If you could not visit our web site, contact our sales

ofce near your sight.

WARNING

●Never use this product as a sensing device for personnel protection.

●In case of using sensing devices for personnel protection, use

products which meet laws and standards, such as OSHA, ANSI or

IEC etc., for personnel protection applicable in each region or country.

INTENDED PRODUCTS FOR CE MARKING

●Refer “our web site (

http://panasonic.net/id/

pidsx/global

)” for the intended products.

●Contact for CE

Panasonic Marketing Europe GmbH Panasonic Testing Center

Winsbergring 15, 22525 Hamburg,Germany

2PART DESCRIPTION

Operation mode switch

(Note 3)

L: Light-ON

D: Dark-ON

Sensitivity adjuster

(Note 2)

Se ns in g ra nge b ec o mes

longer when turned clockwise

Operation indicator

(Orange) (Note 1)

L i g ht s u p w he n t h e

sensing output is ON

Stability indicator (Green)

(Note 1)

Li gh t s u p u n de r th e

stable light condition or

the stable dark condition

●Front sensing

●Side sensing

Notes: 1) Not incorporated on the thru-beam type sensor emitter.

2) Not incorporated on the thru-beam type sensor receiver.

3) Incorporated on the thru-beam type sensor receiver only.

3MOUNTING

●The tightening torque should be 0.5N·m or less.

M3 screw

M3 pan head

screw (Note)

Note: When mounting the front sensing type sensor, use M3 pan

head screws without washers, etc.

4WIRING DIAGRAMS

(Brown) +V

(Black)

Output (Note)

(Blue) 0V

Load

12 to 24V DC

±10%

●PNP output type

(Brown) +V

(Black)

Output (Note)

(Blue) 0V

Load +

12 to 24V DC

±10%

●NPN output type

Note:

The thru-beam type sensor emitter does not incorporate the output.

http://panasonic.net/id/pidsx/global

Overseas Sales Division (Head Ofce)

2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan

Phone: +81-568-33-7861 FAX: +81-568-33-8591

For sales network, please visit our website.

PRINTED IN JAPAN

Produkt Specifikationer

Mærke:	Panasonic
Kategori:	Ikke kategoriseret
Model:	EX22APN

Har du brug for hjælp?

Hvis du har brug for hjælp til Panasonic EX22APN stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panasonic Manualer

Panasonic CS-BKP Manual

1 Juli 2025

Panasonic CS_CU-E9CKP Manual

1 Juli 2025

Panasonic CQ-DPX151U Manual

30 Juni 2025

Panasonic CS-2C19BKP5G Manual

30 Juni 2025

Panasonic CS-C24 Manual

29 Juni 2025

Panasonic CS-12CKE Manual

29 Juni 2025

Panasonic CS-E15CKP Manual

27 Juni 2025

Panasonic CS-E12 Manual

27 Juni 2025

Panasonic CS-V24BKP Manual

24 Juni 2025

Panasonic CS-V18 Manual

24 Juni 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Schneider LUCD1XES Manual

4 Juli 2025

Ikea BLÄDDRARE 304.743.99 Manual

4 Juli 2025

NUX Komp Core Deluxe MKII Manual

4 Juli 2025

Ikea GRÖNAMARANT 204.604.25 Manual

4 Juli 2025

Rowenta Focus DW5121 Manual

4 Juli 2025

Racktime Baskit Breeze 2.0 Manual

4 Juli 2025

Schneider KSB32CP15D Manual

4 Juli 2025

Wiesenfield WIE-IN-100 Manual

4 Juli 2025

Ergotec PM-705N Manual

4 Juli 2025

Sol Expert 19590 Manual

4 Juli 2025