Panasonic EX32APN Manual

Panasonic Ikke kategoriseret EX32APN

Læs gratis den danske manual til Panasonic EX32APN (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 37 personer og har en gennemsnitlig bedømmelse på 4.9 stjerner ud af 19 anmeldelser. Har du et spørgsmål om Panasonic EX32APN, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

INSTRUCTION

MANUAL

Amplier Built-in Type Threaded Miniature Photoelectric Sensor

EX-30 Series

MJEC-EX30 No.0054-69V

Thank you very much for purchasing Panasonic products.

Read this Instruction Manual carefully and thoroughly for

the correct and optimum use of this product. Kindly keep

this manual in a convenient place for quick reference.

● Please refer to “users manual on our web site (http://

panasonic.net/id/pidsx/global)

” for more details

(specication, and operation etc.)

● Access method is “Download” → “Model no.”

● If you could not visit our web site, contact our sales

ofce near your sight.

WARNING

● Never use this product as a sensing device for personnel protection.

● In case of using sensing devices for personnel protection, use

products which meet laws and standards, such as OSHA, ANSI or

IEC etc., for personnel protection applicable in each region or country.

INTENDED PRODUCTS FOR CE MARKING

● Refer “our web site (http://panasonic.net/id/pidsx/global)”

for the intended products.The models listed under “SPEC-

IFICATIONS” come with CE Marking. As for all other mod-

els, please contact our ofce.

● Contact for CE

Panasonic Marketing Europe GmbH Panasonic Testing Center

Winsbergring 15, 22525 Hamburg,Germany

2PART DESCRIPTION

Notes: 1) Not incorporated on the thru-beam type sensor emitter.

2) Incorporated on EX-33□. Not incorporated on the receiver

for EX-31□, and EX-32□.

3) Incorporated on the emitter for EX-33□, and EX-32□. Not

incorporated on

EX-31 □.

3MOUNTING

● Mount the sensor on a mounting plate 3mm

or less thick and Use the enclosed nut and

toothed lock washer for mounting.

● When the nut is tightened, hold the the sensor

with hand or a spanner etc. and the tightening

torque should be 0.6N•m or less. (EX-32□

1N•m or less) Do not tighten the sensor itself.

4WIRING DIAGRAMS

Note:

The thru-beam type sensor emitter does not incorporate the output.

Mounting plate

(3mm or less thick)

Operation mode switch (Note 2)

L: Light-ON

D: Dark-ON

Sensitivity adjuster (Note 3)

Sensing range be-comes

longer when turned clockwise

Operation indicator (Orange) (Note 1)

Lights up when the sensing

output is ON

Stability indicator (Green) (Note 1)

Lights up under the stable light

condition or the stable dark condition

(Brown) +V

(Black)

Output (Note)

(Blue) 0V

Load

12 to 24V DC

±10%

●PNP output type

(Brown) +V

(Black)

Output (Note)

(Blue) 0V

Load

12 to 24V DC

±10%

●NPN output type

＋

－－

＋

5SENSITIVITY ADJUSTMENT

Step

Turn the sensitivity adjuster fully counterclockwise

to the minimum sensitivity position, MIN.

In the light received condition, turn the sensitivity

adjuster slowly clockwise and conrm the point A

where the sensor enters the “Light” state operation.

In the dark condition, turn the sensitivity

adjuster further clockwise until the sensor en-

ters the “Light” state operation and then bring

it back to conrm point B where the sensor

just returns to the “Dark” state operation.

If the sensor does not enter the “Light” state

operation even when the sensitivity adjuster is

turned fully clockwise, the position is point B.

4. The position at the middle of points A and

B is the optimum sensing position.

6CAUTIONS

● This product has been developed / produced for industrial use only.

● The thin cable 0.1mm2 is used for this product. Thus, take care that

if the cable is pulled with excessive force, it may cause cable break.

● Extension up to total 50m (emitter and receiver each for thru-

beam type), or less, is possible with 0.3mm

2, or more, cable.

● Make sure that stress by forcible bend or pulling is not

applied directly to the sensor cable joint.

● Make sure to carry out wiring in the power supply OFF condition.

● Take care that wrong wiring will damage the sensor.

● Verify that the supply voltage variation is within the rating.

● If power is supplied from a commercial switching regu-

lator, ensure that the frame ground (F.G.) terminal of the

power supply is connected to an actual ground.

● In case noise generating equipment (switching regulator, inverter

motor, etc.) is used in the vicinity of this product, connect the

frame ground (F.G.) terminal of the equipment to an actual ground.

● Do not run the wires together with high-voltage lines or

power lines or put them in the same raceway. This can

cause malfunction due to induction.

● Do not use during the initial transient time (50ms) after

the power supply is switched ON.

● Take care that the sensor is not directly exposed to uorescent

lamp from a rapid-starter lamp, a high frequency lighting de-

vice or sunlight etc., as it may affect the sensing performance.

● This sensor is suitable for indoor use only.

● Do not use this sensor in places having excessive vapor, dust,

etc., or where it may come in contact with corrosive gas, etc.

● Take care that the sensor does not come in contact with oil, grease,

organic solvents such as thinner, etc., strong acid, or alkaline.

● This sensor cannot be used in an environment contain-

ing inammable or explosive gases.

● Never disassemble or modify the sensor.

● In case of using the sensor at a place where static electricity is generated,

use a metal mounting plate. Also, ensure to ground the mounting plate.

7RoHS DIRECTIVE

● This equipment complies with RoHS (EC and Chinese directive).

● Chinese RoHS indicates inclusion despite regulation value. (Refer Chinese part.)

Optimum position

http://panasonic.net/id/pidsx/global

Overseas Sales Division (Head Ofce)

2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan

Phone: +81-568-33-7861 FAX: +81-568-33-8591

For sales network, please visit our website.

PRINTED IN JAPAN

Produkt Specifikationer

Mærke:	Panasonic
Kategori:	Ikke kategoriseret
Model:	EX32APN

Har du brug for hjælp?

Hvis du har brug for hjælp til Panasonic EX32APN stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panasonic Manualer

Panasonic MX-HG4401 Manual

10 Oktober 2025

Panasonic EY3794 Manual

8 Oktober 2025

Panasonic CS-ME14CB1P Manual

1 Oktober 2025

Panasonic AV-HSW10 Manual

18 September 2025

Panasonic SD3-A1 Manual

15 September 2025

Panasonic PT-DW5100 Manual

27 August 2025

Panasonic PT-D4000 Manual

26 August 2025

Panasonic NB-G211 Manual

14 August 2025

Panasonic NN-TK81KC Manual

13 August 2025

Panasonic KX-TG3101 Manual

26 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Dahua Technology HAC-HFW1230S-POC Manual

28 Oktober 2025

Dahua Technology HAC-HDW1400TLMQ-A Manual

28 Oktober 2025

Dahua Technology EVS7124D Manual

27 Oktober 2025

Dahua Technology XVR7816S-4KL-X-LP Manual

27 Oktober 2025

Dahua Technology HAC-HDW1220EM Manual

27 Oktober 2025

Dahua Technology ISC-M6550 Manual

27 Oktober 2025

Dahua Technology EVS7148D Manual

27 Oktober 2025

Dahua Technology HAC-HFW2249E-A Manual

27 Oktober 2025

Dahua Technology XVR5108/16H-X Manual

27 Oktober 2025

Dahua Technology XVR5108HE-4KL-I2 Manual

27 Oktober 2025