Panasonic NA1PK3PN Manual

Panasonic Ikke kategoriseret NA1PK3PN

Læs gratis den danske manual til Panasonic NA1PK3PN (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 48 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 24.5 anmeldelser. Har du et spørgsmål om Panasonic NA1PK3PN, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Internal circuit Users' circuit

Color code /

Connector pin No. of the pigtailed type

(Brown / 1) +V

(Note 2)

(Blue / 3) 0V

(Black / 4) Output (Note 1)

100mA max.

1

Job indicator

lighting circuit

Load

12 to 24V DC

±10%

(Pink / 2) Job

indicator input

Main circuit

Job indicator input

Output (Note)

Connector-pin position (Pigtailed type)Ɣ

Notes: 1) The output is not incorporated in the emitter.

2) When the job indicator is used as a large size op-

eration indicator, connect the job indicator input wire

(pink) of the emitter and receiver to the output wire

(black) of the receiver.

Non-voltage contact or PNP open-collector transistor

High (4 to 30V DC): Lights up

Low (0 to 0.6V DC or Open): Lights off

Note: No connection is required for the emitter.

BEAM ALIGNMENT

1. Place the emitter and the receiver face to face

along a straight line.

2. After the cables have been correctly connected,

switch the power ON.

3. Move the emitter in the up, down, left and right

directions, in order to determine the range of

the beam received condition with the help of the

operation indicator (red) on the receiver. Then,

set the emitter at the center of this range.

4. Similarly, adjust for up, down, left and right an-

gular movement of the emitter.

5. Further, perform the angular adjustment for the

receiver also.

6. Check that the stable incident beam indicator

(green) lights up.

7. Interrupt each beam channel with the actual

VHQVLQJREMHFWDQGFRQ¿UPWKDWWKHVHQVRURS-

erates correctly.

Note: The stable incident beam indicator (green) lights up

when all the three beams are stably received by the

receiver.

Emitter

Receiver

Stable incident beam

indicator (Green)

Operation indicator

(Red)

INSTRUCTION MANUAL

NA1-PK3 Series

Thank you very much for using SUNX products.

Please read this Instruction Manual carefully and

thoroughly for the correct and optimum use of

this product. Kindly keep this manual in a conve-

nient place for quick reference.

PART DESCRIPTION

Job indicators (Orange)

Emitter Receiver

Job indicators (Orange)

Power indicator (Green)

Frequency

selection

switch

Operation /

frequency

selection

switch

Stable incident

beam indicator

(Green)

Operation

indicator (Red)

If this product is used as a sensing de-

vice for personnel protection, serious

body injury or death could result.

Never use this product as a sensing device

with any press machine, shearing machine,

roll grinding machine, forming machine, vul-

canizer, or robot etc. for protection of a hand

or a part of the body.

This product does not include a self-check-

ing circuit for safety functions necessary

to allow its use as a safety device. Thus, a

system failure or malfunction can result in

either an energized or a de-energized output

condition.

When this product is used as a sensing

device in the following applications and if a

problem relating to “law” or “product liability”

occurs, SUNX shall not be liable for the fail-

ure and for the damage or less.

1) Use of this product installed to a machin-

ery or a device as a sensing device to

detect a hand or a part of the operator’s

body entering a dangerous area and stop

the machinery or the device.

2) Installation of this product to a protection

device for preventing to enter a dangerous

area and use of this as a sensing device

which detects a hand or a part of the op-

erator’s body and open / close the door or

window.

3) Use of this product as a sensing device for

personnel protection (including interlock).

For sensing devices to be used as safety

devices for press machines or for person-

nel protection, use products which meet

standards, such as OSHA, ANSI or IEC etc.,

for personnel protection applicable in each

region or country.

In case of using as a safety device for press

machine, use a product approved by the

Ministry of Health, Labor and Welfare in Ja-

pan.

Job indicator

lighting circuit

Internal circuit Users' circuit

(Brown / 1) +V

(Blue / 3) 0V

(Note 2)

100mA max.

1

Load +

12 to 24V DC

±10%

Color code /

Connector pin No. of the pigtailed type

(Pink / 2) Job

indicator input

(Black / 4) Output

(Note 1)

Main circuit

I/O CIRCUIT DIAGRAMS

Job indicator input

Output (Note)

Connector-pin position (Pigtailed type)Ɣ

Non-voltage contact or NPN open-collector transistor

Low (0 to 2V DC): Lights up

High (5 to 30V DC or Open): Lights off

Note: No connection is required for the emitter.

Notes: 1) The output is not incorporated in the emitter.

2) When the job indicator is used as a large size op-

eration indicator, connect the job indicator input wire

(pink) of the emitter and receiver to the output wire

(black) of the receiver.

MOUNTING

M4 screws

with washers

M4 nuts

The sensor protection bracket (MS-NA3-3) (op-

tional) is also available.

Sensor protection

bracket ( )MS-NA3-3

(Optional)

Mounting method

Insert the sensor protec-

tion bracket (MS-NA3-3)

from upwards of the sen-

sor body, and match the

position of the mounting

holes of the sensor body

and the sensor protec-

tion bracket (MS-NA3-3).

M o u n t w i t h t h e M 4

screws with washers and

the M4 nuts enclosed

with the sensor protec-

tion bracket ( ).MS-NA3-3

The tightening torque

should be 0.5N·m or

less.

Use M4 screws with washers and M4 nuts. The

tightening torque should be 0.5N·m or less.

Please arrange the screws and the nuts

separately.

SELECTION OF OUTPUT OPERATION

The output operation can be selected by the

operation / frequency selection switch on the

receiver. (Make sure to set the switch in the

power supply off condition.)

State of operation / frequency selection switch

Output operation

L-ON

L - O N

FREQ.

D - O N

FREQ.

OFF whe n

one or more

bea ms are

interrupted.

D-ON

O N w h e n

one or more

bea ms are

interrupted.

L - O N

FREQ.

D - O N

FREQ.

Notes: 1) Selection of the output operation and the frequency

for the receiver is carried out with the same switch.

When the output operation is set, be sure to select

the same frequency No. of the emitter and the re-

ceiver.

2) In case the operation / frequency selection switch is

set to the position other than 1, 2 or 3, the state of

the receiver is in D-ON / frequency 1.

INTERFERENCE PREVENTION FUNCTION

By setting different emission frequencies, three

sets of the sensors can be mounted closely as

VKRZQLQWKH¿JXUHEHORZ

Sensor 1

Sensor 2

Sensor 3

However, if the sensors are mounted closely as

VKRZQLQWKH¿JXUHEHORZXSWR VHWVRIVHQ-

sors are possible.

Sensor 1

Sensor 2

Set the both emitting and receiving frequency

of Sensor 1 to FREQ. 1, the both emitting and

receiving frequency of Sensor 2 to FREQ. 2

and the both emitting and receiving frequency

of Sensor 3 to FREQ. 3. (Make sure to set the

switch in the power supply off condition.)

Frequency setting

Emitter Receiver

Frequency selection switch Operation / Frequency selection switch

Sensor 1

L-ON

FREQ.

L - O N

FREQ.

D - O N

FREQ.

D-ON

FREQ.

L- ON

FREQ.

D - ON

FREQ.

Sensor 2

L-ON

FREQ.

L - O N

FREQ.

D - O N

FREQ.

D-ON

FREQ.

L - O N

FREQ.

D - O N

FREQ.

Sensor 3

L-ON

FREQ.

L- ON

FREQ.

D - ON

FREQ.

D-ON

FREQ.

L - O N

FREQ.

D - O N

FREQ.

Notes: 1) Take care that selection of the output operation and

the frequency for the receiver is carried out with the

same switch.

2) In case the frequency switch and the operation / fre-

quency selection switch is set to the position other

than 1, 2 or 3, the state of the emitter is in frequency

1 and that of the receiver is in D-ON / frequency 1.

7SPECIFICATIONS

Type NPN output PNP output

2m cable length type 5m cable length type 2m cable length type 5m cable length type

Item

Model No. (Note 1)

NA1-PK3

NA1-PK3-C5 NA1-PK3-PN NA1-PK3-PN-C5

Sensing height 49.2mm

Sensing range 30 to 300mm

Beam pitch 24.6mm

Number of beam channels

3 beam channels

Sensing object ø29mm or more opaque object

Supply voltage 12 to 24V DC±10% Ripple P-P10% or less

Current consumption Emitter: 30mA or less, Receiver: 50mA or less

Output

NPN open-collector transistor

Maximum sink current: 100mA

Applied voltage: 30V DC or less (between output and 0V)

Residual voltage: 1V or less (at 100mA sink current)

0.4V or less (at 16mA sink current)

•

PNP open-collector transistor

Maximum source current: 100mA

Applied voltage: 30V DC or less (between output and +V)

Residual voltage: 1V or less (at 100mA source current)

0.4V or less (at 16mA source current)

•

Output operation ON or OFF when one or more beam channels are interrupted, selectable by a switch

Short-circuit protection

Incorporated

Response time 10ms or less (when interference prevention is used: 30ms or less)

Indicators

Emitter

Power indicator: Green LED (lights up when the power is ON)

Job indicator: Orange LED (lights up when the job indicator input is Low)

Power indicator: Green LED (lights up when the power is ON)

Job indicator: Orange LED (lights up when the job indicator input is High)

Receiver

Operation indicator: Red LED (lights up when the output is ON)

Stable incident beam indicator: Green LED

(lights up when the all beams are stably received)

Job indicator: Orange LED (lights up when the job indicator input is Low)

Operation indicator: Red LED (lights up when the output is ON)

Stable incident beam indicator: Green LED

(lights up when the all beams are stably received)

Job indicator: Orange LED (lights up when the job indicator input is High)

Interference prevention function

Incorporated (Up to 3 units can be closely mounted) (Note 2)

Ambient temperature –10 to +55°C (No dew condensation or icing allowed), Storage: –20 to +70°C

Ambient humidity 35 to 85% RH, Storage: 35 to 85% RH

Emitting element Infrared LED (synchronized scanning system)

Material Enclosure: Heat-resistant ABS, Lens cover: Acrylic, Display cover: Acrylic

Cable

0.2mm24-core (emitter: 3-core)

oil resistant cabtyre cable, 2m long

0.2mm

24-core (emitter: 3-core)

oil resistant cabtyre cable, 5m long

0.2mm24-core (emitter: 3-core)

oil resistant cabtyre cable, 2m long

0.2mm24-core (emitter: 3-core)

oil resistant cabtyre cable, 5m long

Weight Emitter: Approx. 50g

Receiver: Approx. 50g

Emitter: Approx. 105g

Receiver: 110g

Emitter: Approx. 50g

Receiver: Approx. 50g

Emitter: Approx. 105g

Receiver: 110g

1RWHV  7KHPRGHO1RZLWKVXI¿[³-J” is pigtailed type. (cable length: 0.3m)

Model No.: NA1-PK3(-PN)-J

For the cable connected with the pigtailed type, use the connection cable CN-24-C2 (cable length: 2m) (optional) or

CN-24-C5 (cable length: 5m) (optional).

2) For details, refer to “ INTERFERENCE PREVENTION FUNCTION.”

PRINTED IN JAPAN

Overseas Sales Dept. (Head Office)

2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan

Phone: +81-(0)568-33-7861 FAX: +81-(0)568-33-8591

Europe Headquarter: Panasonic Electric Works Europe AG

Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany

Phone: +49-8024-648-0

US Headquarter: Panasonic Electric Works Corporation of America

629 Central Avenue New Providence, New Jersey 07974 USA

Phone: +1-908-464-3550

URL : sunx.jp

SUNX Limited

This product has been developed / produced for

industrial use only.

Make sure that the power supply is off while wir-

ing and operation of the selection switch.

Take care that wrong wiring may damage the sensor.

Verify that the supply voltage variation is within

the rating.

If power is supplied from a commercial switch-

ing regulator, ensure that the frame ground

(F.G.) terminal of the power supply is connected

to an actual ground.

Do not use during the initial transient time (0.5

sec.) after the power supply is switched on.

In case noise generating equipment (switching

regulator, inverter motor, etc.) is used in the vicin-

ity of the sensor, connect the frame ground (F.G.)

terminal of the equipment to an actual ground.

Extension up to total 100m is possible with

0.3mm2, or more, cable for both emitter and re-

ceiver. However, in order to reduce noise, make

the wiring as short as possible.

Do not run the wires together with high-voltage lines

or power lines or put them in the same raceway.

This can cause malfunction due to induction.

Take care that the sensor is not directly exposed

WRÀXRUHVFHQWODPSIURPDUDSLGVWDUWHUODPSD

high frequency lighting device or sunlight etc.,

as it may affect the sensing performance.

Avoid dust, dirt, and steam.

Take care that the product does not come in

contact with water, oil, grease, organic solvents,

such as thinner, etc., strong acid or alkaline.

Make sure to use an isolation transformer for

the DC power supply. If an auto-transformer

(single winding transformer) is used, this prod-

uct or the power supply may get damaged.

In case a surge is generated in the used power

supply, connect a surge absorber to the supply

and absorb the surge.

The emitter and the receiver must face each

other correctly. If they are set upside down, the

sensor does not work.

,QRUGHU WRWXUQWKHVZLWFKHVDÀDWKHDGVFUHZ-

driver is required. (The blade should be 2.5 ×

0.6mm or less)

This sensor is suitable for indoor use only.

CAUTIONS

INTENDED PRODUCTS FOR CE MARKING

The models listed under “ SPEC-

IFICATIONS” come with CE Mark-

ing.

As for all other models, please con-

WDFWRXURI¿FH

Produkt Specifikationer

Mærke:	Panasonic
Kategori:	Ikke kategoriseret
Model:	NA1PK3PN

Har du brug for hjælp?

Hvis du har brug for hjælp til Panasonic NA1PK3PN stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panasonic Manualer

Panasonic NB-G211 Manual

14 August 2025

Panasonic NN-TK81KC Manual

13 August 2025

Panasonic KX-TG3101 Manual

26 Juli 2025

Panasonic ER-CKL1 Manual

26 Juli 2025

Panasonic F-48DGL Manual

26 Juli 2025

Panasonic CZ-RTC4A Manual

26 Juli 2025

Panasonic DMW-LND58GU Manual

26 Juli 2025

Panasonic DMR-BWT750 Manual

25 Juli 2025

Panasonic AK-HRP1015G Manual

25 Juli 2025

Panasonic KX-TCA430 Manual

21 Juli 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

B-Tech BT8390-SA Manual

18 August 2025

Festo ZSB-1/8-B Manual

18 August 2025

D-Link DI-701 Manual

18 August 2025

Festo SIEF-M30B-NS-S-L Manual

18 August 2025

Festo P.BE-CMMP-SC-SW-DE Manual

18 August 2025

Festo VACC-S18-120-K4-1U-KS4ME Manual

18 August 2025

Festo SIED-M18NB-ZO-S-L Manual

18 August 2025

Festo P.BE-CP-FB11-E-IT Manual

18 August 2025

Martin Exterior Dot-4 Pro Manual

18 August 2025

Festo SOE4-FO-L-HF2-1P-M8 Manual

18 August 2025