Panasonic PM2LF10 Manual

Panasonic Ikke kategoriseret PM2LF10

Læs gratis den danske manual til Panasonic PM2LF10 (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 13 personer og har en gennemsnitlig bedømmelse på 4.6 stjerner ud af 7 anmeldelser. Har du et spørgsmål om Panasonic PM2LF10, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/1

INSTRUCTION MANUAL

CAUTIONS2

●

This product has been developed / produced for in-

dustrial use only.

A reverse supply protection circuit and output short-

circuit protection circuit are not incorporated. Since

wrong wiring may cause malfunction, make sure to

check the terminal arrangement, cable wiring and

power supply area before wiring.

Make sure that the power supply is o while wiring.

Verify that the supply voltage variation is within the rating.

If power is supplied from a commercial switching reg-

ulator, ensure that the frame ground (F.G.) terminal of

the power supply is connected to an actual ground.

Do not use during the initial transient time (50ms) af-

ter the power supply is switched on.

Do not run the wires together with high-voltage lines

or power lines or put them in the same raceway. This

can cause malfunction due to induction.

For the connector type, the cable length must be 2m,

or less, with 0.3mm2, or more, cable. If the cable is

extended for more than 2m, connect a capacitor of

10 F approx. between +V and 0V terminals. Fur-μ

ther, the cable type cannot be extended.

Avoid dust, dirt, and steam.

Take care that the sensor does not come in direct

contact with water, oil, grease, or organic solvents,

such as, thinner etc.

Take care that the sensor is not directly exposed to

uorescent lamp from a rapid-starter lamp or a high

frequency lighting device, as it may aect the sens-

ing performance.

If there is a reective object (conveyor, etc.) in the

background, since it may aect the sensing, use by

keeping enough distance from the reective object.

Thank you very much for purchasing Panasonic

products. Please read this Instruction Manual

carefully and thoroughly for the correct and

optimum use of this product. Kindly keep this

manual in a convenient place for quick reference.

SPECIFICATIONS1

Enclosure: Polycarbonate, terminal part (Connector type only): HSM (Ag plated)

Cable xing part (Cable type only): PBT

Material

0.2mm2 3-core cabtyre cable, 1m long (Cable type only) (Note 2)Cable

45 to 85% RH, Storage: 45 to 85% RHAmbient humidity

-10 to +55 (No dew condensation or icing allowed), Storage: -25 to +80℃ ℃

Ambient temperature

0.8ms or lessResponse time

Incorporated

Light-ON Dark-ON Dark-ONLight-ONDark-ONLight-ON

Over current protection

Output operation

Average: 25mA or less, Peak: 80mA or less

Current consumption

Output

5 to 24V DC 10% Ripple P-P 5% or lessSupply voltage ±

2.5 to 8mm (Convergent point 5mm) with white non-glossy paper (15 15mm) (Note 1)×

NPN open-collector transistor

・Maximun sink current: 100mA

・Applied voltage: 30V DC or less (between output and 0V)

・Residual voltage: 1V or less (at 100mA sink current), 0.4V or less (at 16mA sink current)

Sensing range

L type (Top sensing)

PM2-LL10-C1

PM2-LL10

PM2-LL10B-C1

PM2-LL10B

Front sensing

PM2-LF10-C1

PM2-LF10

PM2-LF10B-C1

PM2-LF10B

Top sensing

PM2-LH10-C1

PM2-LH10

PM2-LH10B-C1

PM2-LH10B

Type

Model

No.

Cable

Connector type

Item

Notes: 1)

Take care that, depending on the product, the sensing range may extend to 12.5mm maximum with white non-glossy paper.

The cable cannot be extended.

●If soldering is done directly on the terminals, strictly

adhere to the conditions given below.

Soldering temperature: 260 or less℃

Soldering time: 10 sec. or less

Soldering position: 1.5mm, or more, away from the sensor body.

SOLDERING (Connector type only)

1.5mm

Soldering position

0V OUT ＋V

●

When xing the sensor with screws, use M3 screws and

the tightening torque should be 0.49N m or less. Fur-・

thermore, use small, round type plain washers ( 6mm).φ

MOUNTING5

PM2 Series

Photoelectric Sensor

Micro-photosensor

This bag is a product made from polyethylene. Even if it burns, harmful gas is not generated.

●

Never use this product as a sensing device for personnel protection.

In case of using sensing devices for personnel protection, use products which meet

standards, such as OSHA, ANSI or IEC etc., for personnel protection applicable in each

region or country.

WARNING

I/O CIRCUIT DIAGRAMS3

100mA max.

Color code of cable type

and mainting cable

lack ) Output

(Blue

) 0V

(Brown) + V

Internal circuit

Users' circuit

Sensor circuit

Load

5 to 24V DC

±10%

INTENDED PRODUCTS FOR CE MARKING

●The models listed under ' SPECIFICA-

TIONS' come with CE Marking. As for all

other models, please contact our oce.

PRINTED IN JAPAN © Panasonic Electric Works SUNX Co., Ltd. 2011

Overseas Sales Division (Head Office)

2431-1 Ushiyama-cho, Kasugai-shi, Aichi, 486-0901, Japan Phone: +81-568-33-7861 FAX: +81-568-33-8591

Europe Headquarter: Panasonic Electric Works Europe AG

Rudolf-Diesel-Ring 2, D-83607 Holzkirchen, Germany Phone: +49-8024-648-0

US Headquarter: Panasonic Electric Works Corporation of America

629 Central Avenue New Providence, New Jersey 07974 USA Phone: +1-908-464-3550

http://panasonic-electric-works.net/sunx

Produkt Specifikationer

Mærke:	Panasonic
Kategori:	Ikke kategoriseret
Model:	PM2LF10

Har du brug for hjælp?

Hvis du har brug for hjælp til Panasonic PM2LF10 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Panasonic Manualer

Panasonic FP-7113 Manual

6 Juni 2025

Panasonic CY-BT100N Manual

4 April 2025

Panasonic CY-VHD9500U Manual

4 April 2025

Panasonic CY-VMX6800U Manual

4 April 2025

Panasonic CY-EM100N Manual

3 April 2025

Panasonic CQ-DF602W Manual

3 April 2025

Panasonic CQ-DF203W Manual

3 April 2025

Panasonic SH-FX60 Manual

3 April 2025

Panasonic SH-FX80 Manual

3 April 2025

Panasonic SH-PD10 Manual

3 April 2025

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

AmpliVox Airvox SW695 Manual

15 Juni 2025

Stiga SBC 635 KD Manual

15 Juni 2025

Cleveland 36CGM300 Manual

15 Juni 2025

Gourmia GTF7970 Manual

15 Juni 2025

Planet Audio P9630B Manual

15 Juni 2025

ORNO OR-DOM-YR-934UD Manual

15 Juni 2025

Lavex 842CD12VST12 Manual

15 Juni 2025

Marshall RCP-PLUS Manual

15 Juni 2025

Hughes & Kettner BassForce XL Manual

15 Juni 2025

Hughes & Kettner Red Box Mk III Manual

15 Juni 2025