Panasonic TX-32LS490 Manual

Panasonic televisión TX-32LS490

Læs gratis den danske manual til Panasonic TX-32LS490 (2 sider) i kategorien televisión. Denne vejledning er vurderet som hjælpsom af 16 personer og har en gennemsnitlig bedømmelse på 4.7 stjerner ud af 8.5 anmeldelser. Har du et spørgsmål om Panasonic TX-32LS490, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

31-2000914 05-21

I. Removing the Handle

1. Locate the set screws on the handle caps (they are usually on the

less visible side).

2. Loosen the set screw on one end with the 1/8” Allen wrench while

supporting the handle. Do not remove the set screw from the

handle cap (ﬁg 1).

3. Keep supporting the handle while you loosen the set screw on the

other handle cap. Lift the handle from the fasteners on the door

and set aside.

II. Replacing a New Handle

1. Make sure the set screws are loosened. Place the handle over the

fasteners of the door (we recommend putting the screw side of the

handle toward the less visible side). Take care to support the

handle so it doesn’t fall and scratch the appliance ﬁnish. Make sure

both the handle caps are resting on the face of the door.

2. Lock one end of the handle into position by tightening the set

screw in the handle cap with the 1/8” Allen wrench. Be sure not to

over tighten.

3. Keep supporting the handle as you lock the other end of the

handle into position by tightening the set screw in the handle cap

with the 1/8” Allen wrench. Be sure not to over tighten.

Repeat these instructions on all other handles.

Instructions for Replacing Appliance Handles

Instrucciones En Español | Instructions En Français:

www.cafeappliances.com/custom-hardware/installation/

3/16” Allen Wrench

(not included)

1/8” Allen Wrench

(included with handle)

Tools You Will Need:

Replacing Your Café Knobs & Handles

LOOSEN

ﬁg. 1

ﬁg. 2

fastener

handle cap

set screw

The handle on your appliance may have a dierent orientation than what is

shown, but the installation will be the same.

Be extra careful of the appliance ﬁnish around the handle area, as it can

scratch. During removal of the handle screws, hold onto the handle tightly

so it won’t fall and scratch the appliance. We recommend having another

person help you hold the handle in place as you remove the screws.

When the handle has been removed, check the fasteners that are

attached to the appliance front to see if they are loose. If so, tighten them

with a 3/16” Allen wrench before attaching the new handle.

Note: Fastener shape may vary by appliance.

For appliances with multiple handles, look at your current conﬁguration

before removing the handles, and make sure the replacement handles

match that logo and set screw position.

IMPORTANT!

Turn o power to your appliance before you remove or

replace the knobs.

Work with one knob at a time to ensure you don’t mix up

replacement pieces.

Make sure you check the writing on each of your knobs

(and/or bezels) and set them out in the order you will

replace them. This will help ensure you don’t put them

on in the wrong order.

If your appliance has an oven, you will need to replace

the bezels and Oven Mode Selector. If your appliance

does NOT have an oven, you will only have to replace

the knobs and bezels.

IMPORTANT!

Instructions for Replacing Knobs with Bezels and Mode Selectors

Instrucciones En Español | Instructions En Français:

www.cafeappliances.com/custom-hardware/installation/

Phillips Head Screwdriver

(Not included)

Tools You Will Need:

I. Oven Mode Selector

1. Make sure all knobs are in the OFF position

2. Determine if your unit has an Oven Mode Selector (ﬁg. 1). If your unit does not have an

Oven Mode Selector, skip to Section II.

3. First, remove the knob on the Oven Mode Selector by pulling it free from the shaft. You

may have to wiggle it slightly as you pull (ﬁg. 1).

4. Then, grasp the sides and rear of the Oven Mode selector and pull ﬁrmly away from

the appliance until it’s free from the Oven Controls Shaft.

5. Your kit may come with more than one Oven Mode Selector. Make sure you choose

the correct one from the kit by checking the wording on the removed Oven Mode

Selector and matching it to the replacement Oven Mode Selector.

6. Align bigger tab on oven control shaft to the bigger slot on the oven mode selector,

then center it over the oven control shaft. Push onto the shaft as far as possible (ﬁg. 2).

7. Next, match the replacement knob with the knob you’ve removed—make sure they

have the same writing and markings.

8. Hold the replacement knob so that the indicator is at the top and it lines up properly

with the shaft, then push the knob onto the shaft as far as possible for a snug ﬁt.

II. Removing the Current Knobs and Bezels

1. Make sure all knobs are in the OFF position.

2. Choose which knob you will work with ﬁrst, and remove it by grasping the sides and

pulling away from the appliance until the knob is free from its shaft. You may have to

wiggle it slightly as you pull.

3. Using a Phillips head screwdriver, remove the two bezel attachment screws.

4. You should be able to remove the bezel from the appliance front after the screws

have been removed.

5. Repeat the above removal steps for all burner and griddle bezels.

III. Installation of the Replacement Knobs and Bezels

Repeat the following steps 1 - 6 using the Burner and Griddle Bezel Tools to install all

knobs and bezels. Use the Burner Bezel Tool when installing burner knobs and the Griddle

Bezel Tool when installing the griddle knob (on some models).

1. Using the Burner/Griddle Bezel Tool, align the arrow on the tool with the indicator

notch on the bezel, and insert the tool into the bezel.

2. Push the Burner/Griddle Bezel Tool and bezel onto the valve shaft with indicator notch

and arrow pointing upward. Press tool onto the shaft until it is snug and release (ﬁg. 4).

3. Drive the two bezel attachment screws into the bezel. (Partially drive the ﬁrst screw,

fully drive the second screw, then fully drive the ﬁrst screw.)

4. Remove the Burner/Griddle Bezel Tool.

5. Match the replacement knob with the knob you’ve removed. Make sure they have the

same writing and markings.

6. Hold the replacement knob so that the indicator is at the top and it lines up properly

with the shaft. Push the knob onto the shaft as far as possible so it ﬁts snugly (ﬁg. 5).

7. Press the knob and rotate to ensure normal operation. If the knobis dicult to push

in or rotate, visually check if the valve stem is centered within the bezel hole. If the

valve shaft is not centered, loosen the bezel screws, reposition the bezel to be

centered to valve shaft, then retighten screws.

ﬁg. 3

ﬁg. 4

ﬁg. 2

ﬁg. 1

31-2000914 05-21

Burner Bezel Tool

Included with Bezel)

ﬁg. 5

REMOVE

Indicator notch

Valve Shaft

Oven Mode Selector

Griddle Bezel Tool

(Included with Bezel)

Oven Controls Shaft

Oven Mode Selector

A L I G N

Valve Shaft

Bezel Hole

Produkt Specifikationer

Mærke:	Panasonic
Kategori:	televisión
Model:	TX-32LS490

Har du brug for hjælp?

Hvis du har brug for hjælp til Panasonic TX-32LS490 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

televisión Panasonic Manualer

Panasonic Viera TX-L32D28 Manual

9 April 2025

Panasonic TX-L24C5B Manual

9 April 2025

Panasonic TX-24E302B Manual

9 April 2025

Panasonic TX-26LX62FA Manual

9 April 2025

Panasonic TX-24CS500B Manual

9 April 2025

Panasonic TX-65JX870B Manual

10 Marts 2025

Panasonic TX-65LZ980B Manual

11 Februar 2025

Panasonic TX-65MZ2000B Manual

11 Februar 2025

Panasonic TX-58JX820E Manual

2 Februar 2025

Panasonic Viera TH-42PX45B Manual

12 Januar 2025

televisión Manualer

Nyeste televisión Manualer

9 April 2025

9 April 2025

9 April 2025

9 April 2025

9 April 2025

9 April 2025

Sharp 70GL4360E Manual

9 April 2025

TCL 75P69K Manual

9 April 2025

TCL 32S5K Manual

9 April 2025

Philips 65PUL5924 Manual

8 April 2025