Parasound ZRK Manual

Parasound Ikke kategoriseret ZRK

Læs gratis den danske manual til Parasound ZRK (1 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 20 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 10.5 anmeldelser. Har du et spørgsmål om Parasound ZRK, eller vil du spørge andre brugere om produktet?

Download PDF
Side 1/1
A
B
C
D
M3 x 8mm
M4 x 10mm
Kit Contents:
4 brackets(A, B, C, D)
8pcs M3 8mm screw x
4pcs M4 10mm screw x
1) Remove the feet from both units as needed.
2) Install the 4 brackets A, B, C and D using two screws per bracket
as shown in the diagram. All labels should face out.
Only use the screw holes with arrows.
3) Connect the two units by bringing brackets B and C together
and secure with two screws on the front and two screws on the back.
Note: Brackets B and C fit very tightly together. You may need to
angle the two units as you bring them together. See figure 1 below.
4) Mount the units in the equipment rack using plastic insulated
“shoulder” washers to reduce the chance of ground loops caused
by chassis to chassis contact with other equipment in the rack.
Instructions for mounting two half-width
products side-by-side using the ZRK rack
mount kit. This kit works with both
Z Custom and ZoneMaster products.
Figure 1
* The blank panel extender is not used
(this is only used when mounting a single unit)
Steps to Rack Mount Two Units Side-by-Side
1) Remove the feet from the unit as needed.
2) Install bracket C and D using two screws per bracket
as shown in the diagram. All labels should face out.
Only use the screw holes with arrows.
3) Attach the blank panel extender to bracket C using two screws.
Note: You can reverse the side the unit is mounted by following
figure 2 below.
4) Mount the unit in the equipment rack using plastic insulated
“shoulder” washers to reduce the chance of ground loops caused
by chassis to chassis contact with other equipment in the rack.
Instructions for rack mounting a single
Z Custom or half-width ZoneMaster
product using the ZRK kit.
C
D
Blank Panel Extender
Alternative Mounting with Unit on Left Side
A
B
Use These Holes
Steps to Rack Mount a Single Unit
Recycle These Unused Pieces:
Bracket A
Bracket B
Extra Screws
Figure 2
Rotate “B” so that the
theads are on the front
M3 x 8mm
M4 x 10mm

Produkt Specifikationer

Mærke: Parasound
Kategori: Ikke kategoriseret
Model: ZRK

Har du brug for hjælp?

Hvis du har brug for hjælp til Parasound ZRK stil et spørgsmål nedenfor, og andre brugere vil svare dig


Ikke kategoriseret Parasound Manualer

Parasound

Parasound Halo JCM 250 Manual

10 Juli 2025
Parasound

Parasound Halo A 21 Manual

11 Marts 2025
Parasound

Parasound ZoneMaster 4 DAX Manual

11 Marts 2025
Parasound

Parasound John Curl Tribute Edition JC 100 Manual

11 Marts 2025
Parasound

Parasound ZPhono USB Manual

11 Marts 2025
Parasound

Parasound ZoneMaster ZM12 Manual

9 Marts 2025
Parasound

Parasound ZRK Manual

10 August 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Vaxis

Vaxis Litecomm 8S Manual

6 December 2025
Advantech

Advantech ABDNA-ER-IN5010 Manual

6 December 2025
ELO

ELO I-Series 4 E747123 Manual

6 December 2025
Bosch

Bosch SPV4EMX24F Manual

6 December 2025
Compex

Compex Sport Elite Manual

6 December 2025
Fostex

Fostex P650K Manual

6 December 2025
Opticis

Opticis DVFC-100 Manual

6 December 2025
Fostex

Fostex P800K Manual

6 December 2025
Bosch

Bosch WAN24055PL Manual

6 December 2025
Zotac

Zotac GAMING GeForce RTX 5060 Ti 16GB Twin Edge Manual

6 December 2025