Park Tool THS-1 Manual

Park Tool Ikke kategoriseret THS-1

Læs gratis den danske manual til Park Tool THS-1 (4 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 56 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 28.5 anmeldelser. Har du et spørgsmål om Park Tool THS-1, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/4

5115 Hadley Ave. N., St. Paul, MN 55128 (USA) www.parktool.com

PARK TOOL CO.

THS-1 Trailhead Workstation and THP-1 Mounting Post

THS-1 Backplate Sub-Assembly

1. Place carriage bolts through the square holes

with the arms aligned to the mounting holes

on the backplate.

2. Once both arms are in place with the carriage

bolts showing, place the mount plate horizon-

tally along the top two and bottom two car-

riage bolts as shown (Figure 1).

3. Hand tighten the four lock nuts to retain the

arms onto the back plate.

4. Align the arms parallel. Once aligned, torque

the carriage bolt nuts to 20 ft-lbs (27 Nm).

5. Install grips onto arm ends, keeping logo text

horizontal. Optional: utilize an aerosol hair

spray or other spray adhesive to aid assembly

and retain grip permanently.

THS-1 Mounting to a Permanent Structure

1. Complete Backplate Sub-Assembly prior to

mounting to vertical surface.

2. Align the four outer-most mounting holes on the

THS-1 backplate sub-assembly with the desired

position on the ﬂat wall. If mounting to post, use

the center two holes. Utilize backplate as a tem-

plate to mark holes for any drilling.

3. It is recommended to place the bottom mount-

ing holes 54" above the ground. Additional-

ly, ensure adequate space surrounding the

stand is available to clear a bicycle mounted

in the stand.

4. Utilize four ½" (13mm) diameter concrete an-

chor studs (or similar fastener for other mate-

rials) to mount to a concrete wall (Figure 2). If

mounting to post, use two fasteners in center

two holes. Fasteners not included. Follow fas-

tener manufacturer recommendations for hole

sizing, drilling, and applied torque.

THP-1 Mounting to Ground

1. The THP-1 has been designed to be mount-

ed to the Park Tool #130 baseplate or to a con-

crete surface.

Direct Mount: Utilize four ½" (13mm) diame-

ter concrete anchor studs (or similar fasten-

er for other materials) to mount to surface

(Figure 3). Follow fastener manufacturer

recommendations for hole sizing, drilling,

and applied torque. Fasteners not included.

#130 Baseplate: Utilize four ¼-20 fasteners

to assemble the THP-1 to the Park Tool #130

baseplate (Figure 4). Fasteners not included.

2. Ensure top tube square cap is pressed in securely.

THP-1 Post Protector

1. Vertically align the tall side of the ﬁlm with

the forward face of the THP-1. Center the ﬁlm

on the post, 2" above the baseplate and press

onto the post. Start with the forward face and

apply pressure outwards, wrapping the sides

around the post and working air out from the

center to the edges (Figure 5).

THS-1 Mounting to the THP-1

1. Complete Backplate Sub-Assembly prior to

mounting to the THP-1.

2. Align the middle two vertical mounting holes

on the THS-1 backplate sub-assembly with the

smaller two holes on the THP-1 post. Place the

socket head cap screw from the back of the post

into the hole. Hand tighten the nut onto the back-

plate. Repeat for the lower fastener (Figure 6).

3. Once positioned correctly and hand tightened,

torque the nuts to 50 ft-lbs (68 Nm).

4. Ensure top tube square cap is pressed in securely.

THS-1 Tools and Cover Assembly

1. Place tool cable into slotted backplate tab in

locations desired for each tool (Figure 7). There

should be four on each side of the arms. The

cable stop should sit on top of the slotted tab.

2. Hinge front cover by aligning and placing the

top two back cover tabs into the respective

slots on the front cover and rotating the base

of the cover down (Figure 8). Ensure cables re-

main in each slot.

3. Align the three holes, one on each side, and

one centered on the bottom of the front cov-

er, and hand tighten all three tamper proof fas-

teners. Once all three are hand tightened, use

supplied TR27 tool to tighten fasteners. Keep

tool in safe place for future use.

4. Check to ensure all cables are situated in their

slot and none are pinched.

THS-1 & THP-1 Instructions / Instructions / Anleitung / Instrucciones

Produkt Specifikationer

Mærke:	Park Tool
Kategori:	Ikke kategoriseret
Model:	THS-1

Har du brug for hjælp?

Hvis du har brug for hjælp til Park Tool THS-1 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Park Tool Manualer

Park Tool BX-2.2 Manual

11 Juni 2024

Park Tool WAG-4 Manual

11 Juni 2024

Park Tool ES-1 Manual

11 Juni 2024

Park Tool PRS-3.2 Manual

11 Juni 2024

Park Tool PCS-4 Manual

11 Juni 2024

Park Tool TS-4.2 Manual

11 Juni 2024

Park Tool CWP-7 Manual

11 Juni 2024

Park Tool BX-3 Manual

11 Juni 2024

Park Tool CCP-44 Manual

11 Juni 2024

Park Tool THS-1 Manual

11 Juni 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

Kenu Airframe Wireless AFW-KK-NA Manual

4 November 2025

Beverage-Air Horizon HF1HC-1HS Manual

4 November 2025

EKO K400FDGC Manual

4 November 2025

Intermatic OP5GY24 Manual

4 November 2025

Abus Secoris BUBE60020 Manual

4 November 2025

Hillvert HT-TEMPLE-1 Manual

4 November 2025

Yamazen KABF-120H Manual

4 November 2025

RADEMACHER RolloTron Standard 1300 Manual

4 November 2025

ANCEL MT700 Manual

4 November 2025

Schneider Homeline HOM250PSPD Manual

4 November 2025