PCE Instruments PCE-RE100P Manual

PCE Instruments Joystick PCE-RE100P

Læs gratis den danske manual til PCE Instruments PCE-RE100P (10 sider) i kategorien Joystick. Denne vejledning er vurderet som hjælpsom af 28 personer og har en gennemsnitlig bedømmelse på 5.0 stjerner ud af 14.5 anmeldelser. Har du et spørgsmål om PCE Instruments PCE-RE100P, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/10

PCE-RE100P-EN-03-190211 1/10

PCE-RE100P Series Programmable Profile Controller

Thank you for choosing series programmable profile controller. PCE-RE100P

* 96x96mm sized.

* 3,5 inches TFT , graphic and 5 digit display.

* Selectable TC, RTD, NTC, R, mA, V or mV inputs.

* Input offset feature

* 32 point linearization for analog inputs.

* Selectable relay, SSR or analog outputs.

* Selectable , input proportional transmitter output(mA or V).

* 50ms sampling time.

* PID control.

* PID selftune.

* PID auto-tune.

Selftune automatic PID calculation or

manually enter PID parameters if known.

* Soft-Start feature.

* 24Vdc for sensor supply.

* 16 program and 8 step for profile control.

* Selectable Single Setpoint Mode or Profile Control Mode.

* Digital inputs for profile control.

* Security levels for menu and configuration pages.

* RS485 ModBus protocol communication feature.(optional)

* CE marked according to Europen Norms.

* In case of sensor failure manually , periodical or auto-periodical

control can be selected.

Analog Inputs

DIGITAL INPUTS (In order to use for profile control process)

OUTPUTS

ENVIRONMENTAL CONDITIONS

ELECTRICAL CHARACTERISTICS

HOUSING

Input Type

200,0 ... 1800,0 C°

-100,0 ..... 900,0 C°

-100,0 ... 1300,0 C°

-100,0 ..... 900,0 C°

-200,0 ... 1300,0 C°

0,0 ... 1700,0 C°

-250,0 ..... 300,0 C°

-200,0 ..... 400,0 C°

-200,0 ..... 850,0 C°

-100,00 ... 160,00°C

-60,0 ..... 150,0 C°

5V or 30V pulse , Ri=100kΩ

% 0.1 or 2 C (3,6 F)± ± ° °

% 0.1 or 0,5 C (1 F)± ± ° °

Accuracy

+ undefined

+ purple

+ black

+ green

+ red

+ lilac

+ orange

+ brown

+ red

Sensor current 250 Aµ

Cable ColorInput Resist.

- white

- blue

- white

- brown

% 0.1 or 0,5 C (1 F)± ± ° °

% 0.1 or 1 C (1.8 F)± ± ° °

% 0.1 or 1 digit± ±

% 0.1 or 1.5 C (2.7 F)± ± ° °

Range

392,0 ... 3272,0 F°

-148,0 ... 1652,0 F°

-148,0 ... 2372,0 F°

-148,0 ... 1652,0 F°

-328,0 ... 2372,0 F°

32,0 ... 3092,0 F°

-418,0 ..... 572,0 F°

-328,0 ..... 752,0 F°

-328,0 ... 1562,0 F°

-148,00 .. 320,00°F

-76,0 ..... 302,0 F°

RTD

NTC

Ω% 0.5 or 10± ± Ω

B (Pt30Rh-Pt6Rh)

E (NiCr-Con)

J (Fe-Con)

K (NiCr-Ni)

L (Fe-Con)

N (NiCrSi-NiSi)

R (Pt13Rh-Pt)

S (Pt10Rh-Pt)

T (Cu-Con)

U (Cu-Con)

Pt100

NTC

0 - 20mA

4 - 20mA

0 - 150mV

0 - 5V

1 - 5V

0 - 10V

0 - 550

0 - 10k

Control / Alarm 3

Alarm 1

Alarm 2

SSR

Ambient/storage temp.

Max. Relative humidity

Rated pollution degree

Height

Supply

Power consumption

Wiring

EMC

Safety requirements

Housing type

Dimensions

Weight

Enclosure material

Ri 50=Ω

Sensor current 250 Aµ

EN 60751

Standart

% 0.1 or 20 V± ± µ

% 0.2 or 0.1± ± Ω

EN 60584

DIN43710

250V AC, 2A . Selectable as NO+NC.10.000.000 switch without load and 200.000 switch under 250V AC 2A (resistive load)

250V AC, 2A . Selectable as NO.10.000.000 switch without load and 200.000 switch under 250V AC 2A (resistive load)

Max. 40mA , 0 - 12Volt , short-circuit protection.

0 - 20mA or 4 - 20mA , Max. load resistance is 750 .

Max. 30mA , 0 - 10Volt , short-circuit protection.

Ri 100k>Ω

-32768 ... 32767

-3276,8 ... 3276,7

-327,68 ... 327,67

-32,768 ... 32,767

Do not use the device in locations subject to corrosive and flammable gases.

0 ... +50°C/-25 ... 70°C

Suitable for flush-panel mounting.

Relative humidity 80% for temperatures up to .31°C °C , decreasing linearly to 50% relative humidity at 40

G96xY96xD81mm

According to Front panel Rear EN 60529 : IP65 ,

panel : IP20

Approx. 400g.

Max. 2000m

Self extinguishing plastics.

While cleaning the device , solvents(thinner,gasoline,acid etc.) or corrosive materials must not be used.

2 0V AC, 50/60Hz90- 5

Max. 7 VA

2.5mm² screw-terminal

EN 61326-1: 201 3

EN 61010-1: 201 (0 Pollution degree 2 , overvoltage category ||)

°C

1230.6

1200.0

SSR

Prog.No: Seg.No: 1 1

Prog.Remaining Time(min): 1:0

°C

PRESS SET TO START PROFILE CONTROLLER

Read this document carefully before using this device. The guarantee will be expired by device damages if you don’t attend to the directions

in the user manual. Also we don't accept any compensations for personal injury, material damage or capital disadvantages.

Start-Stop Input

Previous Program Input

Next Program Input

Pause-Resume Input

200

175

150

125

100

PV-SV

min

2 4 6 8 10 12 14 16

Program 1 is running

PCE-RE-100P

PCE Teknik Cihazlar Paz. Tic. Ltd.Şti.

Halkalı Merkez Mah. Pehlivan Sok. No 6/C

34303 Küçükçekmece/ İstanbul

Türkiye

96mm

6mm 69mm 15mm

PANEL CUT-OUT

92mm

DIMENSIONS

Not :

1) Panel thickness should be maximum 7mm.

2) If there is no 60mm free space at the back

side of the device , it would be difficult to remove it from

panel.

Flush mounting clamp

For removing the device from panel :

- While pressing both flush mounting clamps of the device

in direction pull it in direction 1 , 2.

16 29

17 30

18 31

19 32

20 33

Control

Alarm 3

Valve On

Alarm 1

Alarm 2

Valve Off

90 - 230V AC

50/60Hz, MAX. 7VA

+24V DC (max. 30mA)

GND1

+12V DC (max. 30mA)

RTD

NTC

COM

ModBus

RS 485 B

{

V OUT

mA OUT

SSR OUT

Previous Program Input

Pause - Resume Input

Start - Stop Input

Next Program Input

+12V

GND

TCmA/mV/V

PCE-RE100P is intended for installation in control panels. Make sure that the device is used only for intended purpose. The electrical connections

must carried out by a qualified staff and must be according to the relevant locally applicable regulations. During an installation , all of the cables that

are connected to the device must be free of electrical power. The device must be protected against inadmissible humidity , vibrations , severe soiling