Philips 42FD9935 Manual

Philips TV 42FD9935

Læs gratis den danske manual til Philips 42FD9935 (19 sider) i kategorien TV. Denne vejledning er vurderet som hjælpsom af 29 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 15 anmeldelser. Har du et spørgsmål om Philips 42FD9935, eller vil du spørge andre brugere om produktet?

Side 1/19
1
CORRECTLY INCORRECTLY
Note: the enclosed template can be used for general positioning only
(fig. 1).
Mounting to sheetrock wall
Note: Bracket can only be used with standard 16" spaced wood wall
studs.
Bracket must be positioned so that the bracket is fastened firmly to
studs at each end.
All required hardware is included.
Note: Because the Receiver Units power cord is 6’, when determining the
Display Unit mounting location, the distance to the nearest AC power
outlet must be considered.
&Determine desired location to mount Display Unit.
Within this area, locate the two 16.54" spaced wall studs that must
be used as the Wall Bracket mounting location. (fig. 1 and 2)
éWith the Wall Bracket held in place, ensure it is properly leveled.
Then, mark where the four holes must be drilled. (fig. 2)
Note: Use only the holes in Bracket.
Remove the Wall Bracket, and using a 13/64" wood drill bit, drill the
four holes. (fig. 3)
Reposition the Wall Bracket, and with four lag bolts (fig. 4), secure
into place.Tighten with 13mm or 1/2" socket wrench. (fig. 5)
Note: Do not use plastic wall anchors with these lag bolts.
Note: Lag bolts must be fastened and centered securely into the stud.
Mounting Wall Bracket
fig. 1
fig. 2
420mm /16,54"
60,5mm / 2.38"
fig. 3
fig. 4
fig. 5
English
2
Mounting to concrete wall
& Determine desired location to mount Display Unit. Use the enclosed
template for alignment purposes. (fig. 1)
éWith the Wall Bracket held in place, ensure it is properly leveled.
Then, mark where the four holes must be drilled. (fig. 4)
Remove the Wall Bracket, and using a 5/8" masonry drill bit, drill the
four holes. (fig. 2)
Insert a concrete anchor (with bolt) into each hole.
(Firmly tighten each bolt.Then, remove the bolts.
§Reposition the Wall Bracket, and with the four bolts (and washers),
secure into place.
Mounting to concrete block wall
&Determine desired location to mount the Display Unit.
Within this area, position the Wall Bracket so that the four end
mounting holes are located over the cavities of the concrete blocks
(refer to Figure 1)
éWith the Wall Bracket held in place, ensure it is properly leveled.
Then, mark where the four holes are to be drilled.
Note: Use only the four outside or end holes in the Bracket.
Remove the Wall Bracket and reconfirm that the marks made in the
previous step are located in the cavities of the concrete blocks. Re-
locate the marks as required to ensure that they are in the cavities
of the concrete blocks.
With a 1/2masonry drill bit, drill the four holes.
(Hinge the plastic legs of the toggle bolt into the channel of the metal
end of the toggle bolt so it can fit into the 1/2hole drilled in the
wall (refer to Figure 2).
§Insert the toggle bolt into the hole in the wall and push it in until it
is in the cavity of the block.
èWith the plastic pull ring of the toggle bolt, pull the metal end of the
toggle bolt firmly against the back of the cavity of the concrete block
(refer to Figure 3).
WASHER
Cavities In Block
Fig. 1
Fig. 2
Fig. 3


Produkt Specifikationer

Mærke: Philips
Kategori: TV
Model: 42FD9935

Har du brug for hjælp?

Hvis du har brug for hjælp til Philips 42FD9935 stil et spørgsmål nedenfor, og andre brugere vil svare dig