Porter-Cable 75301 Manual

Porter-Cable Ikke kategoriseret 75301

Læs gratis den danske manual til Porter-Cable 75301 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 49 personer og har en gennemsnitlig bedømmelse på 4.4 stjerner ud af 25 anmeldelser. Har du et spørgsmål om Porter-Cable 75301, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

To use the 75301 Height Adjuster with a router mounted in a table, there needs to be a

hole (or holes) in the table for the Adjuster to reach the router.

IMPORTANT: The instructions below are for some speciﬁ c situations where holes

NEED TO BE DRILLED. Check your table to see if holes are already provided to

allow the Adjuster clearance.

If you are not using a Porter-Cable router table, your router’s sub-base (S) Fig. 2 can be

used as a template to determine where holes need to be drilled. Use the instructions be-

low as a general guide on how to attach the Adjuster for a non-Porter-Cable table.

DISCONNECT ROUTER FROM POWER SOURCE BEFORE

ASSEMBLING THE HEIGHT ADJUSTER.

WHEN USING WITH THE 698 ROUTER TABLE

AND THE 890 SERIES ROUTERS:

1. Make sure router is not attached to the table. Remove the router’s plastic sub-base

(an example of one type used with the 890 router is shown in Fig. 3).

2. Flip the table over with the fence side on top, as in Fig. 4. Then, with the smooth

side of the sub-base against the bottom of the table, line up the three holes (A)

Fig. 3 in the sub-base with the three holes (C) Fig. 4 in the table. Make sure holes (B)

Fig. 3 are on the bottom when the three holes (A) and (C) are aligned.

3. Use the screws supplied with the table to hold the sub-base in place. Looking straight

down on holes (B) Fig. 3, center punch or mark a spot in the table in the center of

these holes (B).

4. Before you drill the holes, be sure the table is arranged so nothing below

it will be damaged during drilling.

5. Move the sub-base. At your marks, drill a 7/16" hole. Approximate location of the

holes for the 890 Series is represented by the dotted white circles in Fig. 4.

6. Turn table over and attach router as described in the owner’s manual.

7. Insert Height Adjuster so the index ring (R) rests on the table top (as shown in Fig. 1)

and the adjusting arm’s hex opening matches the hex screw in the router.

WHEN USED WITH THE 698 ROUTER TABLE

AND THE 8529 PLUNGE ROUTER:

1. Make sure router is not attached to the table. Remove the router’s plastic sub-base

(shown in Fig. 5).

2. Flip the table over with the fence side on top, as in Fig. 4. Then, with the smooth

side of the sub-base against the bottom of the table, line up the three holes (D)

Fig. 5 in the sub-base with the three holes (C) Fig. 4 in the table. Make sure hole (E)

Fig. 5 is on the bottom right when the three holes (D) and (C) are aligned.

3. Use the screws supplied with the table to hold the sub-base in place. Looking straight

down on hole (E) Fig. 5, center punch or mark a spot in the table in the center of hole

(E).

4. Before you drill the hole, be sure the table is arranged so nothing below

it will be damaged during drilling.

5. Move the sub-base. At your mark, drill a 7/16" hole. Approximate location of the hole

for the 8529 is represented by the dotted white circle in Fig. 4.

6. Turn table over and attach router as described in the table’s manual.

7. Insert Height Adjuster so the index ring (R) rests on the table top (as shown in Fig. 1)

and the adjusting arm’s hex opening matches the hex screw in the router.

Fig. 1

Fig. 5

Fig. 4

Router Table Fence Side

ESPAÑOL en revés / FRANÇAIS sur l’inverse

890 series 8529

Fig. 2

Fig. 3

890 series

8529

A23842 - 07-16-07

Porter-Cable, 4825 Hwy. 45 North, Jackson TN 38305

www.deltaportercable.com (888) 848-5175

For your own safety, read your router's instruction manual before using

any accessory. Failure to heed these warnings may result in personal injury and serious

damage to the router and the accessory. When servicing this tool, use only identical

replacement parts.

To reduce the risk of injury, turn unit off and disconnect it from power source

before installing and removing accessories, before adjusting or when making repairs. An

accidental start-up can cause injury.

Height Adjuster Model 75301

Produkt Specifikationer

Mærke:	Porter-Cable
Kategori:	Ikke kategoriseret
Model:	75301

Har du brug for hjælp?

Hvis du har brug for hjælp til Porter-Cable 75301 stil et spørgsmål nedenfor, og andre brugere vil svare dig

Dit navn*

Din email*

Skriv dit spørgsmål her

Ikke kategoriseret Porter-Cable Manualer

Porter-Cable PCCF930 Manual

3 December 2024

Porter-Cable 6931 Manual

10 August 2024

Porter-Cable 59381 Manual

6 August 2024

Porter-Cable TS056 Manual

1 August 2024

Porter-Cable 8931 Manual

1 August 2024

Porter-Cable 557 Manual

31 Juli 2024

Porter-Cable 4210 Manual

24 Juli 2024

Porter-Cable 42690 Manual

19 Juli 2024

Porter-Cable 59380 Manual

26 Juni 2024

Porter-Cable PC160JT Manual

9 Marts 2024

Ikke kategoriseret Manualer

Nyeste Ikke kategoriseret Manualer

BirdDog Central 20 Manual

4 December 2025

SPT SET-04S Manual

4 December 2025

Cecotec Power Pulsar 2300MAX Cream&Crush Manual

4 December 2025

Scotsman CU3030X Manual

4 December 2025

Powerfix PEK 2.3 B1 Manual

4 December 2025

Vevor SS-004-4P-WH Manual

4 December 2025

Dorr LV-30 Manual

4 December 2025

PERPOTAO WA-K7 Manual

4 December 2025

JET JCT-1600 Manual

4 December 2025

Asko HB150T Manual

4 December 2025