Posiflex MR-2000U-3 Manual

Posiflex Ikke kategoriseret MR-2000U-3

Læs gratis den danske manual til Posiflex MR-2000U-3 (2 sider) i kategorien Ikke kategoriseret. Denne vejledning er vurderet som hjælpsom af 11 personer og har en gennemsnitlig bedømmelse på 4.3 stjerner ud af 6 anmeldelser. Har du et spørgsmål om Posiflex MR-2000U-3, eller vil du spørge andre brugere om produktet?

Download PDF

Side 1/2

Page 1 2 /

MR-2000 Series

MAGNETIC STRIPE READER

USER’S MANUAL

Rev. : C

I. FEATURES

l Double or triple tracks as indicated in MODEL IDENTIFICATION

l Built- -in keyboard wedge interface or RS 232 interface or USB interface as indicated in

MODEL IDENTIFICATION

l Built-in decoder

l Dual directional operation

l Interface cable included

l Heavy duty die cast case

l 3 tracks type MSR can read also AAMVA and CA DMV card

FCC NOTICE

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions manual,

may cause interference to radio communications. It has been tested and found to comply with limits for a Class A digital device pursuant to subpart J of Part

15 of FCC Rules, which are designed to provide reasonable protection against interference when operated in a commercial environment. Operation of this

equipment in a residential area is likely to cause interference in which case the user at his own expense will be required to take whatever measures to correct

the interference.

WARRANTY LIMITS

Warranty will terminate automatically when the equipment is opened by any person other than the authorized technicians. The user should consult

his/her dealer for the problem happened. Warranty voids if the user does not follow the instructions in application of this merchandise. The manufacturer is by

no means responsible for any damage or hazard caused by improper application.

The hardware utility program, including instructions for its use, is provided “AS IS” without warranty of any kind. Posiflex Technologies, Inc.

further disclaims all implied warranties including without limitation any implied warranties of merchantability or of fitness for a particular purpose. The entire

risk arising out of the use or performance of the software and documentation remains with you.

ABOUT THIS MANUAL

This manual is written in an attempt with full strength to assist the user to utilize the stand-alone magnetic stripe reader MR2000 series of Posiflex

POS products. This series of products provide excellent flexibility and reliability in application. This manual covers both operational and technical aspects of

these units.

The manufacturer of the MR2000 series heartily apologizes to the user for reserving the right to change or to modify this manual without notice due

to the rapid and constant progress and improvement on science and technology. The user may always obtain the most up to date information through any of

our web sites: http://www.posiflex.com or http://www.posiflex.com.tw or http://www.posiflexusa.com.

 Copyright Posiflex Technologies, Inc. 2009

All rights are strictly reserved. No part of this documentation may be reproduced, stored in a retrieval system, or transmitted in any form or by any

means, electronic, mechanical, photocopying, or otherwise, without the prior written consent of Posiflex Technologies, Inc. the publisher of this

documentation

TRADE MARKS AND SERVICE MARKS

POSIFLEX is a registered trademark of Posiflex Technologies, Inc. an ISO- - turer.9001 and ISO 14001 certified manufac

Other brand and product names are trademarks and registered trademarks and service marks of their respective owners.

II. MODEL IDENTIFICATIONS

Interface

Applicable tracks PS/2 KB wedge

RS232 USB

ISO track 1 & 2 MR2000-2 MR2000R-2 MR2000U-2

ISO track 2 & 3 MR2000-2/3 MR2000R-2/3 MR2000U-2/3

ISO track 1 & 2 MR2000-3 MR2000R-3 MR2000U-3

JIS track I & II MR2000-JIS (N. A.) (N. A.)

III. SPECIFICATIONS

l Reader specification

Applicable card type

ISO 7811 JIS X 6302

Card feed method

Manual

Card feed direction

Bi-direction

Read / write function

Read only

Card feed speed 5 to 55 inches/sec. 100 ~ 1200 mm/sec.

Error rate Less than 0.5% Less than 0.1%

l Card data format

Data standard IATA ABA THRIFT

JIS I JIS II

Track used Track 1

Track 2

Track 3

(Track 2)

Rear side

Applicable to

models

MR2000-2, 2/3, 3

MR2000R-2, 2/3, 3

MR2000U-2, 2/3, 3

MR2000-JIS

MR2000U-JIS

Recording method

F2F (FM)

Recording density

210 BPI

75 BPI 210 BPI

Recording capacity

characters / bits 79 / 7 40 / 5 107 / 5

40 / 5 72 / 7

Note 1: AAMVA and CA DMV standards are supported in 3 track ISO models

Note 2: For 2 track ISO readers like MR2000- -2 or MR2000U 2/3 info about the missing track in

above table is not applicable

P/N: 19030900030

警告使用者

這是甲類的資訊產品，在居住的環

境中使用時，可能會造成射頻干

擾，，在這種情況下使用者會被要

求採取某些適當的對策。

T31454

Page 2 2 /

l Dimensions: 14.5 cm (L) X 4.6 cm (W) X 3.4 cm (H)

l Weight: 490 gm

l LED: dual color -- green for good read or ready to read

red for invalid read

l Rated voltage: 5 VDC

l Rated current: 100 mA max.

IV. CABLE CONNECTION GUIDE

l Cable connection for KB WEDGE models (MR2000-2/3/JIS)

l Cable connection for RS232 interface models (MR2000R-2/3)

l Cable connection for USB interface models (MR2000U-2/3/JIS)

V. ADJUSTABLE PARAMETERS

Some parameters in readout format of the MR-2000 series in PS/2 KB interface and USB interface

can be controlled by software downloaded from our web site: http://www.posiflex.com. However, saved

parameters must be retrieved after power off and on under proper arrangement for the PS/2 KB interface

model while for USB models parameters are automatically saved even after power off and on. It is also

possible to adjust some parameters with modification in hardware described below if not by software.

Please note that the individual track enable mentioned applies only when the track is supported in

physical reader head.

l For MR2000- -2, 2/3, 3 and MR2000R 2, 2/3, 3:

Changing the status of each jumper in the lower dotted area at right that is the enlarged image of

the shaded area on the

control PCB determines

parameters illustrated in

the table below. For

MR2000R-2, 2/3, 3, the

communication protocol

is default at 9600 bps,

none parity, 8 data bits, 1

stop bit.

Table 1

LEADING /

STOP

CODE ALT + NUM

TRACK 1

TRACK 2

TRACK 3

FUNCTION &

JUMPER

STATUS J1 J2 T1 T2 T3

SHORT DISABLED DISABLED

ENABLED

OPEN ENABLED ENABLED

DISABLED

DEFAULT OPEN DEPENDS

SHORT SHORT SHORT

l For MR2000U-2, 2/3, 3

Changing the jumper status on the

control PCB inside die cast case determines

parameters illustrated in the table below.

Table 2

FUNCTION JUMPER SHORT OPEN DEFAULT

LEADING / STOP CODE

J1 DISABLED ENABLED OPEN

ALT + NUM JP2, PIN 1-2

DISABLED ENABLED SHORT

INIT NUM LOCK JP2, PIN 3-4

DISABLED ENABLED SHORT

CLASS JP2, PIN 7-8

HID VENDOR SHORT

OS JP2, PIN 9-10

WINDOWS / LINUX

DOS SHORT

TRACK 1 T1 ENABLED DISABLED SHORT

TRACK 2 T2 ENABLED DISABLED SHORT

TRACK 3 T3 ENABLED DISABLED SHORT

Note 1: To use the USB interface MSR in operating system without USB support, please set USB

keyboard enabled in BIOS (CMOS) setup.

Note 2: Since this USB interface MSR works as a USB keyboard which is a normal HID (Human

Interface Devices) in USB classification, no special driver shall be required. However, it

should be set as vendor class for Linux system and special driver is required.

MR2000-2, 2/3, 3, JIS

Keyboard

Mini DIN 6 P Male

Mini DIN 6 P Female

KB I/P

PC USB port or USB hub

MR2000U

2. 2/3, 3, JIS

MR2000R-2, 2/3, 3

2.5/5.5 DC plug from power adaptor

D sub 9 P Female

to COM port

LOCATIONS OF SELECTORS

on PCB inside case

S1S5

S S2 4

CN2

JP3

JP4

JP1

CN2

CN1

JP2

Produkt Specifikationer

Mærke:	Posiflex
Kategori:	Ikke kategoriseret
Model:	MR-2000U-3
Vægt:	490 g
Dimensioner (BxDxH):	145 x 46 x 34 mm
LED-indikatorer:	Ja
Grænseflade:	USB
Vægt (efter britisk standard):	1.08 Pund